Quick reference (1.0)

S
UPERMICR
R
ContaCt InformatIon
MNL-1681 -QRG
• Website:www.supermicro.com
• GeneralInformation:[e-mail]
• TechSupport:[e-mail]
• Phone:+1(408)503-8000,Fax:+1(408)503-8008
© 2014 Supermicro Computer Inc. All rights reserved. Reproduction of this document whether in part or in whole is strictly prohibited without Supermicro's written consent. All Trademarks are property of their respective entities. All information provided is deemed accurate at the time of printing; however, it is not guaranteed.
X10DrD-ItP/IntP/LtP
QuICk referenCe GuIDe
• One(1)I/Oshield(MCP-260-00042-0N)
• One(1)I/Oshielddual-portSFPbracket
(MCP-260-00087-0N)
• One(1)QuickReferenceGuide( MNL-1681-QRG)
for your system to work ProPerLy, PLease DownLoaD aPProPrIate
DrIvers/ImaGes/user's manuaL from the LInks beLow:
• Manuals:http://www.supermicro.com/support/manuals/
• Drivers&Utilities:ftp://ftp.supermicro.com/
• Safety: http://www.supermicro.com/about/policies/safety_information.cfm
PaCkaGe Contents
• One(1)SupermicroMotherboard
• Four(4)SATACables(CBL-0044L)
• One(1)iPASSto4-SATAcable
(CBL-0097L-03)(forX10DRD-iTP/iNTP) 
Dual Intel
®
E5-2600 v3 Series processors (Socket R3-LGA 2011); each processor
supports dual full-width Intel QuickPath Interconnect (QPI) links (of up to 9.6 GT/s
one direction per QPI)
Note: Please install both CPUs for full access to the PCI-E slots, DIMM
slots, and onboard controllers. Refer to the block diagram on page 1-10 in
the manual to determine which slots or devices may be affected. Please
populate CPU socket 1 rst.
1
2
Ground
19
20
NMI
X
X
FP PWRLED
3.3 V
HDD LED
UID Switch
NIC1 Link LED
NIC1 Activity LED
NIC2 Link LED
NIC2 Activity LED
UID LED
OH/Fan Fail/
PWR Fail LED)
Power Fail LED
3.3V
Reset Button
Power Button
Ground
Ground
Speed (MT/s)
Voltage (V)
INTEL CONFIDENTIAL
Intel and the Intel logo are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries. Other names and brands
may be claimed as the property of others. All products, dates, and figures are preliminary and are subject to change without any notice. Copyright © 2012, Intel Corporation.
Type
Ranks Per
DIMM
and
Data
Width
DIMM
Capacity (GB)
Speed (MT/s); Voltage (V);
Slot Per Channel (SPC) and DIMM Per Channel (DPC)
1 Slot Per
Channel
2 Slots Per Channel
3 Slots Per Channel
1DPC
1DPC 2DPC 1DPC
2DPC 3DPC
4Gb
8Gb
1.2V
1.2V 1.2V 1.2V 1.2V 1.2V
RDIMM SRx4 8GB 16GB
2133
2133 1866 2133 1866 1600
RDIMM SRx8 4GB 8GB
2133
2133 1866 2133 1866 1600
RDIMM DRx8 8GB 16GB
2133
2133 1866 2133 1866 1600
RDIMM DRx4 16GB 32GB
2133
2133 1866
2133
1866 1600
LRDIMM QRx4 32GB 64GB
2133
2133 2133 2133 2133 1600
DDR4 Memory POR for Haswell-EP
1
CLOSE 1st
OPEN 1st
SAN MAC
BAR CODE
MAC CODE
IPMI CODE
JBAT1
JUSBRJ45
S-SATA0-3
X10DRD-LTP
REV:1.00
BIOS
LICENSE
I-SATA5
I-SATA4
I-SATA0
I-SATA1
I-SATA3
I-SATA2
JSTBY1
JL1
FAN3
FAN7
FAN8
FAN5
FAN6
I-SGPIO2
I-SGPIO1
JTPM1
JPWR1
JPWR3
JF1
JPI2C1
JPL1
JVRM_I2C2
JVRM_I2C1
JPME2
JI2C2
JWD1
JI2C1
JPG1
LED3
LEDM1
LED1
LED4
LED5
LED6
JUIDB1
SP1
SFP1
SFP2
J1_SFP1
J1_SFP2
CPU1 SLOT4 PCI-E 3.0 X8
P1_NVME0
P1_NVME1
P2-DIMMG1
P2-DIMMH1
P1-DIMMC1
P1-DIMMB1
P1-DIMMD1
P1-DIMMA1
IPMI_LAN
COM1
COM2
USB4/5
CPU1 SLOT5 PCI-E 3.0 X8
CPU1
CPU1 SLOT6 PCI-E 3.0 X8
CPU2 SLOT7 PCI-E 3.0 X8
VGA
LAN1
USB2/3
USB0/1
USB6
JPWR2
LAN2
FAN2 FAN1
FAN4
P2-DIMMF1
P2-DIMME1
JPB1
CPU2
PCH
BMC
AST2400
NIC CTRL
Intel 82599
(For -iTP/iNTP, CPU2 req’ed)
(For -iNTP only)
(For -iTP/iNTP)
BIOS
(For -iTP/iNTP/LTP, CPU1 req’ed)
(For -iTP/iNTP, CPU1 req’ed)
(For -iTP/iNTP, CPU1 req’ed)
CLOSE 1st
OPEN 1st
JIPMB1
Jumpers
Motherboard Layout and Features
Jumpers and Connectors
Populating RDIMM/LRDIMM ECC Memory Modules
Back Panel I/O Connectors
Memory Support
CPU Installation
Note: Graphics shown in this quick reference guide are for illustration only. Your components may or may not look exactly the same as the drawings shown in this guide.
Note: Refer to Chapter 1 of the user manual for detailed information on jumpers, connectors, and LED
indicators.
Note: Refer to Chapter 2 of the user manual for detailed information on memory support and CPU/
motherboard installation instructions.
= mounting hole
Heatsink Installation
Front Panel Control (JF1)
CPU Support
Release Tabs
This motherboard supports up to 512 GB of Load Reduced (LRDIMM) or 256 GB of
Registered (RDIMM) DDR4 (288-pin) ECC 2133/1866 MHz modules in eight slots.
Memory speed support depends on the CPUs installed in the motherboard. For the
latest memory updates, please refer to our website at http://www.supermicro.com/
products/motherboard.
Speed (MT/s)
Voltage (V)
2
3
4
5
6
7
8
9
10
1
1. COM Port 1
2. Back Panel USB 2.0 Port 0
3. Back Panel USB 2.0 Port 1
4. IPMI-Dedicated LAN
5. Back Panel USB 2.0 Port 2
6. Back Panel USB 2.0 Port 3
7. 10G_SPF + 10GbE LAN Port 1
8. 10G_SPF + 10GbE LAN Port 2
9. Back Panel VGA (Blue)
10. UID Button/UID LED
LED Indicators
LED Description State Status
LED1 Rear UID LED Blue: On Unit Identied
LED3 SFP+/LAN1 Activity LED Green: Blinking SFP+/LAN1 Active
LED4 SFP+/LAN1 Heartbeat LED Green: Blinking SFP+/LAN1 Normal
LED5 SFP+/LAN2 Activity LED Green: Blinking SFP+/LAN2 Active
LED6 SFP+/LAN1 Heartbeat LED Green: Blinking SFP+/LAN2 Normal
LEDM1 BMC Heartbeat LED Green: Blinking BMC Normal
Notches
OPEN 1st
Screw#1
Screw#2
Mounting Holes
Direction of the airow
Note: For optimal airow, please follow your
chassis airow direction to correctly install the
CPU heatsink.
Socket Keys
CPU Keys
Jumper Description Default Setting
JBT1 Clear CMOS See Chapter 2
JI
2
C1/JI
2
C2 SMB to PCI-E Slots Pins 2-3 (Disabled)
JPB1 BMC Enable Pins 1-2 (Enabled)
JPG1 VGA Enable Pins 1-2 (Enabled)
JPL1 10G_SPF/LAN 1/2 Enable Pins 1-2 (Enabled)
JPME2 Manufacture (ME) Mode Select Pins 1-2 (Normal)
JWD1 Watch Dog Timer Enable Pins 1-2 (Reset)
Connectors Description
JBAT1 (Battery) Onboard CMOS battery
COM1/COM2 Backplane COM Port1/Front accessible COM2 header
FAN 1- 8 CPU/system fan headers (FAN1-FAN8)
IPMI_LAN IPMI_dedicated LAN support by the Aspeed controller
JF1 Front panel control header
JL1 Chassis intrusion header
JPI
2
C1 Power supply SMBbus I
2
C header
JPWR1 24-pin ATX main power connector
JPWR2/JPWR3 12V 8-pin power connectors
JSTBY1 Standby power connector
JTPM1 TPM (Trusted Platform Module)/Port 80 header
P1-NVME0/1 NVM Express PCI-E 3.0 x4 ports supported by CPU1 (for
X10DRD-iNTP only)
I-SATA 0-5 SATA 3.0 connectors supported by Intel PCH (I-SATA 0-5), (I-
SATA4/I-SATA5: can be used as Supermicro SuperDOMs [Devic-
es-on-Module] with built-in power connectors)
I-SGPIO1/2 Seria_Link General Purpose I/O headers 1/2 for SATA ports (I-
SGPIO1 for I-SATA0-3, I-SGPIO2 for I-SATA4/5)
S-SATA0-3 SATA 3.0 connections 0-3 supported by Intel SCU (for X10DRD-
iTP/iNTP only)
SFP+/LAN1 10G_SFP+ (Small-form Factor Pluggable Transceiver)/(10GbE)
LAN Port 1 (J1_SFP1)
SFP+/LAN2 10G_SFP+ (Small-form Factor Pluggable Transceiver)/ (10GbE)
LAN Port 2 (J1_SFP2)
(CPU1)Slot4 PCI-Express 3.0 x8 slot from CPU1 (for X10DRD-iTP/iNTP)
(CPU1)Slot5 PCI-Express 3.0 x8 slot from CPU1 (for X10DRD-iTP/iNTP)
(CPU1)Slot6 PCI-Express 3.0 x8 slot from CPU1 (for X10DRD-iTP/iNTP/LTP)
(CPU2)Slot7 PCI-Express 3.0 x8 slot from CPU2 (CPU2 is required) (for
X10DRD-iTP/iNTP)
SP1 Internal speaker/buzzer
UID-SW (JUIDB1) UID (Unit Identication) switch
(BP) USB 0/1 (2.0) Backpanel USB 2.0 ports 0/1
(BP) USB 2/3 (2.0) Front accessible USB 2.0 connections (USB 2/3) header
(BP) USB 4/5 (2.0) Backpanel USB 2.0 ports 4/5
(FP) USB 6 (2.0) Front accessible Type A 2.0 connector (USB6)
VGA Backpanel VGA port
Connectors
OPEN 1st
OPEN 1st