Quick reference (1.0)

ManualsBrandsSupermicro ManualsServerSSF618R2-FT

http://www.supermicro.com MNL-1647-QRG

Board Layout

SuperServer F618R2-FT Quick Reference Guide

CPU Installation

Front View & Interface

Heatsink Installation

1. Place the heatsink on top of the installed CPU.

2. Align the four screws to the socket.

3. Holding the heatsink in place, screw down as shown

(cross pattern, in order: A, C, B, D).

4. Note: Only use 6-8 lb/f of torque; otherwise, hand-tighten

each screw to avoid damaging the CPU.

Memory

Caution

SAFETY INFORMATION

IMPORTANT: See installation instructions and safety warning

before connecting system to power supply.

http://www.supermicro.com/about/policies/safety_information.cfm

WARNING:

To reduce risk of electric shock/damage to equipment,

disconnect power from server by disconnecting all power

cords from electrical outlets.

If any CPU socket empty, install protective plastic CPU cap

CAUTION:

Always be sure all power supplies for this system have

the same power output. If mixed power supplies are

installed, the system will not operate.

For more information go to :

http://www.supermicro.com/support



Rear View

Description

No.

Low-Profile PCIE Expansion Slot

UID Button

Power Button

VGA Port

Dedicated LAN for IPMI

GbE LAN1/LAN2 Ports

USB 0/1 Ports



Align CPU to socket;

install CPU straight down

NOTE:

Do not bend pin inside socket



Nodes and Corresponding Hard Drives

Description

No.

Power Supply Module

Rear Fan

SCF418IL-R1K62BP

Node 4

Controls two HDDs D1-D2

Node 8

Controls two HDDs H1-H2

Node 3

Controls two HDDs C1-C2

Node 7

Controls two HDDs G1-G2

Node 2

Controls two HDDs B1-B2

Node 6

Controls two HDDs, F1-F2

Node 1

Controls two HDDs A1-A2

Node 5

Controls two HDDs E1-E2

SNK-P0047P for CPU1

Screw #B

Screw #C

Screw #A

SNK-P0057P for CPU2

Description

No.

CPU1 Socket

CPU1 Slot1 PCI-E 3.0 x16

JBT1: CMOS Clear

P1-DIMMA1 / P1-DIMMB1

L-SAS 0~3/4~7: SAS Connectors 0~3/4~7 supported by LSI SAS controller

I-SATA0~5: I-SATA 3.0 Ports (support by the Intel PCH)

S-SATA0/1: S-SATA 2.0 Ports (support by the Intel SCU)

JSD1/JSD2: Disk-On-Module (DOM)

S-SATA2/3: SATA DOM w/power pin built-in connectors 2/3

P1-DIMME1 / P1-DIMMF1

CPU2 Socket

P1-DIMMH1 / P1-DIMMG1

CPU2 Slot2 PCI-E 3.0 x16

JTPM1: Trusted Platform Module Header

DIMMC1 / DIMMD1

S-SATA3

S-SATA2

JSD2

JSD1

S-SATA0

S-SATA1

I-SATA0

I-SATA1

I-SATA2

I-SATA3

I-SATA4

I-SATA5

JIPMB1

JBT1

LEDS1

SW1

COM1

JVRM2

JI2C1

JI2C2

JPB1

JUSB3

P1-DIMMC1

P1-DIMMD1

P2-DIMMG1

P2-DIMMH1

P1-DIMMA1

P1-DIMMB1

P2-DIMME1

P2-DIMMF1

L-SAS0-3

L-SAS4-7

JTPM1

JUIDB1

CPU1 SLOT1 PCI-E 3.0 X16

FAN2

FAN1

CPU2 SLOT2 PCI-E 3.0 X16

CPU2

CPU1

JVRM1

X10DRFF(-C)

Intel PCH

SAS CTRL

JPCIE1

JPCIE2

1213

Processors and their Corresponding Memory Modules

CPU# Corresponding DIMM Modules

CPU 1 P1-DIMMA1 P1-DIMMB1 P1-DIMMC1 P1-DIMMD1

CPU 2 P2-DIMME1 P2-DIMMF1 P2-DIMMG1 P2-DIMMH1

Processor and Memory Module Population for Optimal Performance

Number of

CPUs+DIMMs

(For memory to work properly, please follow the instructions below.)

1 CPU &

2 DIMMs

CPU1

P1-DIMMA1/P1-DIMMB1

1 CPU &

4 DIMMs

CPU1

P1-DIMMA1/P1-DIMMB1, P1-DIMMC1/P1-DIMMD1

2 CPUs &

4 DIMMs

CPU1 + CPU2

P1-DIMMA1/P1-DIMMB1, P2-DIMME1/P2-DIMMF1

2 CPUs &

6 DIMMs

CPU1 + CPU2

P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1

2 CPUs &

8 DIMMs

CPU1 + CPU2

P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1/P2-

DIMMG1/P2-DIMMH1

Populating RDIMM/LRDIMM Memory Modules

Type Ranks

Per

DIMM

& Data

Width

DIMM

Capacity (GB)

Speed (MT/s), Voltage (V), Slot per Channel

(SPC) and DIMM Per Channel (DPC)

1 Slot Per Channel

1DP

4Gb 8Gb

1.2V

RDIMM 8GB 16GB 2133 MHz

RDIMM 4GB 8GB

2133 MHz

RDIMM 16GB 32GB

2133 MHz

LRDIMM 32GB 64GB

2133 MHz

SRx4

SRx8

DRx4

QRx4

Node 4

Node 8

Node 3

Node 7

Node 6

Node 5

Node 2

Node 1

Screw #D

ÌMNL-1647-QRG0Î