Quick reference (1.0)

ManualsBrandsSupermicro ManualsServerSS6028TR-HTFR

http://www.supermicro.com

MNL-1644-QRG

Board Layout

SuperServer 6028TR-HTR/HTFR Quick Reference Guide

Rear View

CPU Installation

Front View & Interface



Heatsink Installation

1. Place heatsink on top of installed CPU

2. Line up the four screws to socket

3. Push down heatsink and screw down as shown

(cross pattern, in order: A, C, B, D)

4. NOTE: Only use 6-8 lb/f of torque; otherwise, hand-tighten

each screw, to avoid damaging the system

Memory

Caution

SAFETY INFORMATION

IMPORTANT: See installation instructions and safety warning

before connecting system to power supply.

http://www.supermicro.com/about/policies/safety_information.cfm

WARNING:

To reduce risk of electric shock/damage to equipment,

disconnect power from server by disconnecting all power

cords from electrical outlets.

If any CPU socket empty, install protective plastic CPU cap

CAUTION:

Always be sure all power supplies for this system have

the same power output. If mixed power supplies are

installed, the system will not operate.

Screw #B

Screw #D

Screw #C

Screw #A

Align CPU to socket;

install CPU straight down

For more information go to :

http://www.supermicro.com/support



NOTE:

Do not bend pin inside socket



SNK-P0047PS

for CPU2

SNK-P0047PW

for CPU1

Note:

Install CPU1 first

Description

No.

JBT1: CMOS Clear

I-SATA0/I-SATA1: SATA3 Drive Connectors

CPU1 (Install CPU1 first)

JSD1/JSD2: SATA DOM Power

S-SATA0/S-SATA1

JTPM1: TPM(Trusted Platform Module)/Port 80

P1-DIMMC1/P1-DIMMD1

P2-DIMME1/P2-DIMMF1

CPU2

P2-DIMMH1/P2-DIMMG1

P1-DIMMA1/P1-DIMMB1

DESIGNED IN USA

FAN3

LE1

JTPM1

JCOM1

JB1

JL1

LEB2

MH1

JI2C2

JBR1

JPME2

JWD1

JP1

JP2

JI2C1

JB3

JB2

JIB1

JPB1

JPL1

JPG1

JVRM1

JPF2

JVRM2

JPF1

JIPMB1

JSD1

JSD2

LE7

LE8

LEDM1

JBT1

BT1

J23

JF1

JPCIE1

SXB2

SXB1

SSATA0

SSATA1

SATA2SATA1

JVGA

JSTBY1

JUIDB1

BIOS LICENSE

IB GUID

X10DRT-H

JIB1:

1-2:ENABLE

2-3:DISABLE

CHASIS INTRUSION

JL1:

JWD1:

2-3:NMI

1-2:RST

S-SATA1

I-SATA0

I-SATA1

:CPU2 SXB2 PCI-E 3.0 X8(INX4)

CPU1 SXB1 PCI-E 3.0 X8(INX4)

CPU1 SLOT1 PCI-E 3.0 X16

S-SATA0

JBR1:

JPME2:

1-2:NORMAL

2-3:ME MANUFATURING MODE

1-2:NORMAL

2-3:BIOS RECOVERY

1-2:ENABLE

JI2C1/JI2C2:

I2C BUS FOR SLOT

2-3:DISABLE

UID

P1-DIMMA1

P1-DIMMB1

P2-DIMMG1

P2-DIMMH1

CPU1

P2-DIMME1

P2-DIMMF1

P1-DIMMD1

1-2:ENABLE

2-3:DISABLE

JPG1:VGA

P1-DIMMC1

TPM/PORT80

JPL1:LAN

JPB1:BMC

2-3:DISABLE

1-2:ENABLE

2-3:DISABLE

1-2:ENABLE

SATA DOM PWR

JBT1:

CMOS

CLEAR

CLOSE 1st

OPEN 1st

CLOSE 1st

OPEN 1st

LEB1

P2-DIMME1

P2-DIMMF1

P2-DIMMG1

P2-DIMMH1

P1-DIMMA1

P1-DIMMB1

VGA

COM1

JLAN1

JLAN2

JUSBRJ45

IPMI_LAN

USB0/1(3.0)

LAN2

LAN1

QSFP

SXB1: CPU1 SXB1 PCI-E 3.0 X8 (INX4)

SXB2: CPU2 SXB2 PCI-E 3.0 X8 (INX4)

JPCIE1: CPU1 SLOT1 PCI-E 3.0 X16

CPU2

Processors and their Corresponding

Memory Modules

CPU# Corresponding DIMM Modules

CPU 1

P1-DIMMA1

P1-DIMMB1 P1-DIMMC1 P1-DIMMD1

CPU2

P2-DIMME1

P2-DIMMF1

P2-DIMMG1 P2-DIMMH1

Processor and Memory Module Population for Optimal Performance

Number of

CPUs+DIMMs

(For memory to work properly, please follow the instructions below.)

1 CPU &

2 DIMMs

CPU1

P1-DIMMA1/P1-DIMMB1

1 CPU &

4 DIMMs

CPU1

P1-DIMMA1/P1-DIMMB1, P1-DIMMC1/P1-DIMMD1

2 CPUs &

4 DIMMs

CPU1 + CPU2

P1-DIMMA1/P1-DIMMB1, P2-DIMME1/P2-DIMMF1

2 CPUs &

6 DIMMs

CPU1 + CPU2

P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1

2 CPUs &

8 DIMMs

CPU1 + CPU2

P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1/P2-

DIMMG1/P2-DIMMH1

Hard Drive Signal

Hard Drive Fail

Power Button

LAN LED

Information LED

UID Button

Description

No.

UID Button

Infiniband Port (6028TR-HTFR only)

VGA Port

COM Port

LAN Ports

USB Ports

Power Supply Module

Low-Profile PCI-E Slot ( up to 5.9”)

IPMI LAN Port

Description

No.

26 4 3

9 8

MB: A

MB: B

MB: C

MB: D

Motherboard Drawer Locations in the Chassis

Motherboard B

Controls HDDs B1, B2 and B3

Motherboard D

Controls HDDs D1, D2, and D3

Motherboard A

Controls HDDs A1, A2 and A3

Motherboard C

Controls HDDs C1, C2 and C3

Nodes and Corresponding Hard Drives

Populating DDR4 DIMM Memory Modules

Type

Ranks

Per

DIMM

& Data

Width

DIMM Capacity

(GB)

Speed (MT/s); Voltage (V); Slot per Chan-

nel (SPC) and DIMM Per Channel (DPC)

1 Slot

Per

Channel

2 Slots Per

Channel

3 Slots Per Channel

1DPC 1DPC 2DPC 1DPC 2DPC 3DPC

4Gb 8Gb 1.2V 1.2V 1.2V 1.2V 1.2V 1.2V

RDIMM SRx4 8GB 16GB 2133 2133 1866 2133 1866 1600

RDIMM SRx8 4GB 8GB 2133 2133 1866 2133 1866 1600

RDIMM DRx8 8GB 16GB 2133 2133 1866 2133 1866 1600

RDIMM DRx4 16GB 32GB 2133 2133 1866 2133 1866 1600

LRDIMM QRx4 32GB 64GB 2133 2133 2133 2133 2133 1600

LRDIMM 3DS 8Rx4 64GB 128GB 2133 2133 2133 2133 2133 1600

ÌMNL-1644-QRGÃÎ