Quick reference (2.0)

ManualsBrandsSupermicro ManualsServerSS6027TR-D71RF+

http://www.supermicro.com MNL-1410-QRG

Board Layout

SuperServer 6027TR-DTRF+/D70RF+/D71RF+ Quick Reference Guide

Rear View

Hard Drive Signal

Hard Drive Fail

Power Button

LAN LED

Alert

UID

Description

No.

BIOS Beep Codes

Beep Code/LED Message Description

1 beep Refresh Circuits have been reset.

(Ready to power up)

5 short beeps + 1 long

beep

Memory

5 long beeps + 2 short

beeps

Display memory

read/write status

Video adapter missing or with

faulty memory

1 continuous beep System System overheat

CPU Installation

Beep Codes

Description

No.

Front View & Interface



Heatsink Installation

1. Place heatsink on top of installed CPU

2. Line up the four screws to socket

3. Push down heatsink and screw down as shown

(cross pattern, in order: A, C, B, D)

4. NOTE: Only use 6-8 lb/f of torque; otherwise, hand-tighten

each screw, to avoid damaging the system

MEMORY

Caution

SAFETY INFORMATION

IMPORTANT: See installation instructions and safety warning

before connecting system to power supply.

http://www.supermicro.com/about/policies/safety_information.cfm

WARNING

To reduce risk of electric shock/damage to equipment,

disconnect power from server by disconnecting all power

cords from electrical outlets.

If any CPU socket empty, install protective plastic CPU cap

CAUTION

Always be sure all power supplies for this system have

the same power output. If mixed power supplies are

installed, the system will not operate.

Align CPU to socket;

install CPU straight down

For more information go to :

http://www.supermicro.com/support



No memory detected

NOTE:

Do not bend pin inside socket



Screw #D

Screw #A

Screw #C

Screw #B

Intel E5-2600 Series Processor UDIMM Memory Support

Note: For detailed information on memory support and updates, please refer to the SMC Recommended Memory List posted on our website at

http://www.supermicro.com/support/resources/mem.cfm.

Ranks per DIMM

& Data Width

Memory Capacity

Per DIMM

(See the Note below)

Speed (MT/s) and Voltage Validated by Slot per Channel (SPC)

and DIMM Per Channel (DPC)

SRx8 Non-ECC

1 Slot Per Channel 2 Slots Per Channel

1DPC 1DPC 2DPC

1.35V

1.5V

1.35V

1.5V

1.35V

1.5V

1GB 2GB 4GB

DRx8 Non-ECC

SRx16 Non-ECC

SRx8 ECC

DRx8 ECC

2GB 4GB 8GB

512MB 1GB 2GB

1GB 2GB 4GB

2GB 4GB 8GB

1066, 1333, 1600

1066, 1333

1066, 1333, 1600

1066, 1333

1066, 1333, 1600

1066, 1333

1066, 1333, 1600

1066, 1333

1066

1066, 1333

1066, 1333, 1600

1066, 1333

1066

1066, 1333

Installing RDIMM (ECC) Memory

Installing UDIMM (ECC/non-ECC) Memory

Intel E5-2600 Series Processor RDIMM Memory Support

Note: For detailed information on memory support and updates, please refer to the SMC Recommended Memory List posted on our website at

http://www.supermicro.com/support/resources/mem.cfm.

Ranks

per

DIMM

& Data

Width

Memory Capacity

Per DIMM

(See the Note below)

Speed (MT/s) and Voltage Validated by Slot per Channel (SPC) and DIMM Per Channel (DPC)

SRx8

1 Slot Per Channel 2 Slots Per Channel

1DPC 1DPC 2DPC

1.35V

1.5V

1.35V

1.5V

1.35V

1.5V

1GB 2GB 4GB

DRx8

SRx4

DRx4

QRx4

2GB 4GB 8GB

4GB 8GB 16GB

8GB 16GB 32GB

1066, 1333

1066, 1333, 1600 1066, 1333, 1600

1066, 1333

1066, 1333, 1600

1066, 1333

1066, 1333, 1600 1066, 1333, 1600

1066, 1333

1066, 1333, 1600

1066, 1333

1066, 1333, 1600 1066, 1333, 1600

1066, 1333

1066, 1333, 1600

1066, 1333

1066, 1333, 1600

1066, 1333

1066, 1333, 1600

1066, 1333

1066, 1333, 1600

800

1066

800

1066

800

QRx8

4GB

8GB

16GB

800

1066

1066, 1333

800

1066 800 800

Processors and Memory Module Population for Optimal Performance

Number of

CPUs + DIMMs

CPU and Memory Population Configuration Table

(For memory to work properly, follow the instructions below)

1 CPU & 2 DIMMs

CPU1 & P1-DIMMA1/P1-DIMMB1

1 CPU & 4 DIMMs

1 CPU & 5~8 DIMMs

2 CPUs & 4 DIMMs

2 CPUs & 6 DIMMs

CPU1 & P1-DIMMA1/P1-DIMMB1, P1-DIMMC1/P1-DIMMD1

CPU1 & P1-DIMMA1/P1-DIMMB1, P1-DIMMC1/P1-DIMMD1 +

Any memory pairs in P1-DIMMA2/P1-DIMMB2/P1-DIMMC2/P1-DIMMD2 slot

CPU1 + CPU2 & P1-DIMMA1/P1-DIMMB1, P2-DIMME1/P2-DIMMF1

CPU1 + CPU2 & P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1

2 CPUs & 8 DIMMs

2 CPUs & 10~16 DIMMs

2 CPUs & 16 DIMMs

CPU1 + CPU2 & P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1/P2-DIMMG1/P2-DIMMH1

+ Any memory pairs in P1, P2 DIMM slots

CPU1 + CPU2 & P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1/P2-DIMMG1/P2-DIMMH1,

P1-DIMMA2/P1-DIMMB2/P1-DIMMC2/P1-DIMMD2, P2-DIMME2/P2-DIMMF2/P2-DIMMG2/P2-DIMMH2

Processors and their Corresponding Memory Modules

CPU#

Corresponding DIMM Modules

CPU 1

P1-DIMMA1

CPU 2 P2-DIMME1

P1-DIMMB1

P2-DIMMF1

P1-DIMMC1

P2-DIMMG1

P1-DIMMD1

P2-DIMMH1

P1-DIMMA2

P2-DIMME2

P1-DIMMB2

P2-DIMMF2

P1-DIMMC2

P2-DIMMG2

P1-DIMMD2

P2-DIMMH2

Installing and Removing Hard Drives

MB: A

MB: B

Note: In order to support the LSI RAID controller, both CPU sockets must be populated.

Note:

Install CPU1 first

Description

No.

FAN4

FAN3

I-SATA0

I-SATA1

JTPM1

X9DRT-HF+

JF2

JIPMB1

J21

JITP0

LE3

JPL1

JPB1

JWD1

JPG1

IPMI_LAN

P1 DIMMA1

P1 DIMMA2

P2 DIMMF2

P2 DIMME1

P1 DIMMD

P1 DIMMD1

P2 DIMMH2

P2 DIMMH1

CPU1 Slot1 PCI-E 3.0 X8

P2 DIMMG1

P2 DIMMG2

P2 DIMMF1

P2 DIMME2

P1 DIMMB

P1 DIMMB1

COM1

VGA

CPU1 Slot2 PCI-E 3.0 X8

LAN1

LAN2

USB2/3

CPU2

P1 DIMMC1

P1 DIMMC2

CPU1

CPU2

BIOS

JBT1

Intel PCH

BMC

LAN CTRL

USB4

LE2

SW1

UID

LE1

USB1

LEM1

XDP-CPU

USB0

JPME1

JPME2

Battery

for SMC-Proprietary Daughter (Add-on) Card

CPU1 Slot2 PCI-E 3.0 x8

for SMC-Proprietary Micro Low-Profile (LP) Card

CPU1 Slot1 PCI-E 3.0 x8

P1-DIMMA1/P1-DIMMA2

P1-DIMMB1/P1-DIMMB2

P1-DIMMC1/P1-DIMMC2

P1-DIMMD1/P1-DIMMD2

P2-DIMME1/P2-DIMME2

P2-DIMMF1/P2-DIMMF2

P2-DIMMG1/P2-DIMMG2

P2-DIMMH1/P2-DIMMH2

CPU1 (Install CPU1 first)

CPU2

SATA 0/1 Connectors

JBT1 = CMOS Reset

TPM Header

Motherboard Drawer Locations in the Chassis

Motherboard B

Controls HDDs B1 to B6

Motherboard A

Controls HDDs A1 to A6

Micro Low-profile Card Slot

UID Button

LAN Ports

Power Supply Module

ÌMNL-1410-QRG>Î