Quick reference (1.0)
http://www.supermicro.com
MNL-1431- QRG
Board Layout
SuperServer 6027TR-D71RF/D71QRF/D71FRF Quick Reference Guide
Rear View
BIOS Beep Codes
Beep Code/LED Message Description
1 beep Refresh Circuits have been reset.
(Ready to power up)
5 short beeps + 1 long
beep
Memory
5 long beeps + 2 short
beeps
Display memory
read/write status
Video adapter missing or with
faulty memory
1 continuous beep System System overheat
CPU Installation
Beep Codes
Front view & Interface
Heatsink Installation
1. Place heatsink on top of installed CPU
2. Line up the four screws to socket
3. Push down heatsink and screw down as shown
(cross pattern, in order: A, C, B, D)
4. NOTE: Only use 6-8 lb/f of torque; otherwise, hand-tighten
each screw, to avoid damaging the system
MEMORY
Caution
SAFETY INFORMATION
IMPORTANT: See installation instructions and safety warning
before connecting system to power supply.
http://www.supermicro.com/about/policies/safety_information.cfm
WARNING
To reduce risk of electric shock/damage to equipment,
disconnect power from server by disconnecting all power
cords from electrical outlets.
If any CPU socket empty, install protective plastic CPU cap
CAUTION
Always be sure all power supplies for this system have
the same power output. If mixed power supplies are
installed, the system will not operate.
Align CPU to socket;
install CPU straight down
For more information go to :
http://www.supermicro.com/support
!
!
No memory detected
NOTE:
Do not bend pin inside socket
!
!
Screw #D
Screw #A
Screw #C
Screw #B
Installing and Removing Hard Drives
JSD1
1
JWP1
P2 DIMMG1
P2 DIMMH
1
P2 DIMMF1
P2 DIMME1
S-SATA0
Always DIMMxA First
CPU1_Port2 SXB1 PCI-E 3.0 x16
1
CPU2
P1 DIMMC1
UID
P1 DIMMD1
CPU1
X9DRT-HF
Rev. 1.21
P1 DIMMB1
PCI-Ex16 (Proprietary)
J4
S-SATA2
I-SATA
1
I-SATA0
P1 DIMMA1
CPU1_Port3A SXB2
PCI-E 3.0 X8
CPU2_Port2C SXB3
PCI-E 3.0 X8
S-SATA3
1
2
13
Description
No.
PCI-E 3.0 x16 slot for Low-Profile Add-on Card
PCI-E 3.0 x8 slot
CPU1_Port3A SXB2
1
2
P1-DIMMA1
P1-DIMMB1
P1-DIMMC1
P1-DIMMD1
P2-DIMME1
P2-DIMMF1
P2-DIMMG1
P2-DIMMH1
CPU1 (Install CPU1 first)
CPU2
SATA 0/1 Connectors
JBT1 = CMOS Reset
JDS1= SATA DOM Power
TPM Header
3
PCI-E 3.0 x8 slot for SMB-Proprietary (Daughter) Card LSI 2108
CPU2_Port2C SXB3
5
6
8
7
9
4
PCI-E x16 Proprietary
15
17
16
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
CPU1 _Port2 SXB1
18
MB: A
MB: B
A
B
Note: In order to support the LSI RAID controller, both CPU sockets must be populated.
Hard Drive Signal
Hard Drive Fail
Power Button
LAN LED
Alert
UID
1
2
3
4
5
6
Description
No.
3
4
5
6
2
1
!
Processors and their Corresponding Memory
Modules
CPU# Corresponding DIMM Modules
CPU 1 P1-DIMMA1 P1-DIMMB1 P1-DIMMC1 P1-DIMMD1
CPU2 P2-DIMME1 P2-DIMMF1 P2-DIMMG1 P2-DIMMH1
Processor and Memory Module Population
Number of
CPUs+DIMMs
CPU and Memory Population Table
(*For memory to work proper, please install DIMMs in pairs)
1 CPU &
2 DIMMs
CPU1
P1-DIMMA1/P1-DIMMB1
1 CPU &
4 DIMMs
CPU1
P1-DIMMA1/P1-DIMMB1, P1-DIMMC1/P1-DIMMD1
2 CPUs &
4 DIMMs
CPU1 + CPU2
P1-DIMMA1/P1-DIMMB1, P2-DIMME1/P2-DIMMF1
2 CPUs &
6 DIMMs
CPU1 + CPU2
P1-DIMMA1/P1-DIMMB1, P2-DIMME1/P2-DIMMF1, P1-DIMMC1/P1-DIMMD1
2 CPUs &
8 DIMMs
CPU1/CPU
P1-DIMMA1/P1-DIMMB1, P2-DIMME1/P2-DIMMF1, P1-DIMMC1/P1-DIMMD1,
P2-DIMMG1/P2-DIMMH1
UDIMM Support on the E5-2600 Series Processor Platform
DIMMs Populated per
DDR Channel
UDIMM Type
(Unb. DIMM)
POR Speeds (in
MHz)
Ranks per DIMM
(Any Combination)
1 ECC/Non-ECC DDR3 1066, 1333 SR, DR
RDIMM Support on the E5-2600 Series Processor Platform
DIMMs Populated per
DDR Channel
RDIMM Type
(Reg. DIMM)
POR Speeds (in
MHz)
Ranks per DIMM
(Any Combination)
1 Reg. ECC DDR3 1066, 1333, 1600 SR, DR
LRDIMM Support on the E5-2600 Series Processor Platform
DIMMs Populated per
DDR Channel
LRDIMM Type
(Load Reduced
DIMM)
POR Speeds (in
MHz)
Ranks per DIMM
(Any Combination)
1 LR ECC DDR3 1066, 1333 QR
Motherboard Drawer
Locations in the Chassis
Motherboard B
Controls HDDs B1 to B6
Motherboard A
Controls HDDs A1 to A6
Description
No.
3
10
7 1
24
56
8
9
1
2
3
4
5
6
7
8
9
10
Full-height & half-length Slots
Low-profile Slot
UID Button
QSFP Port (2027TR-D70QRF/D70FRF only)
VGA Port
COM Port
LAN1/LAN2 Ports
USB Ports
Dedicated LAN for IPMI
Power Supply Module
Note1: Install CPU1 first
Note2:
In order to support SAS
both CPU sockets
must be polpulated.
ÌMNL-1431-QRGTÎ
1011
12
14