Quick reference (1.0)

ManualsBrandsSupermicro ManualsServerSS5018D-MF

http://www.supermicro.com MNL-1456-QRG

Board Layout

SuperServer 5018D-MF Quick Reference Guide

Rear View

Power Button

Reset Button

Power LED

Device Activity LED

LAN1 LED & LAN2 LED

Information LED

Description

No.

CPU Installation

Serial ATA Drive Installation

Description

No.

Front View & Interface

Heatsink Installation

1. Place heatsink on top of installed CPU

2. Line up the four screws to socket

3. Push down heatsink and screw down as shown

(cross pattern, in order: A, C, B, D)

4. NOTE: Only use 6-8 lb/f of torque; otherwise, hand-tighten

each screw, to avoid damaging the system

MEMORY

Caution

Screw #B

Screw #D

Screw #A

123456

SAFETY INFORMATION

IMPORTANT: See installation instructions and safety warning

before connecting system to power supply.

http://www.supermicro.com/about/policies/safety_information.cfm

WARNING:

To reduce risk of electric shock/damage to equipment,

disconnect power from server by disconnecting all power

cords from electrical outlets.

If any CPU socket empty, install protective plastic CPU cap

CAUTION:

Always be sure all power supplies for this system have

the same power output. If mixed power supplies are

installed, the system will not operate.

For more information go to :

http://www.supermicro.com/support



PCI-E Expansion Slot (w/riser card)

UID Button

VGA Port

GbE LAN2 Port

GbE LAN1 Port

USB 4/5/6/7 Ports

COM1 Port

Dedicated LAN for IPMI

Single Power Supply Module

Description

No.

PCH Slot4 PCI-E 2.0 x4 in x8 slot

CPU Slot5 PCI-E 3.0 x8 slot

CPU Slot6 PCI-E 3.0 x8 in x16 slot

CPU

DIMMA1 / DIMMA2 (Blue Slot)

DIMM1B / DIMM2B (Blue Slot)

JBT1 = CMOS Clear

SATA 3.0 (0/1 Ports)

SATA 2.0 (2/3/4/5 Ports)

JSD1 = SATA DOM Power Connector

JTPM1 = Trusted Platform Module/Port 80 Connector

DDR3 Unbuffered Non-ECC (UDIMM) Memory

DIMM Slots per

Channel

DIMMs Populated

per Channel

DIMM Type POR Speeds Ranks per DIMM (any

combination)

2 1 Unb. ECC

DDR3

1066, 1333, 1600 Single Rank, Dual Rank

2 2 Unb.ECC

DDR3

1066, 1333, 1600 Single Rank, Dual Rank

BIOS Error Beep Codes

Beep Code/LED Error Message Description

1 beep Refresh Circuits have been reset.

(Ready to power up)

5 short beeps +

1 long beep

Memory error No memory detected

in the system

8 beeps Display memory

read/write error

gnissim retpada oediV

or with faulty memory

OH LED On System OH System Overheat

Screw #C

1. First power down the system and then remove the top cover of the chassis.

2. Secure the drive to the tray with the four screws.

3. Replace the top cover when finished.

Note: the 5018D-MF can accommodate two internal SATA hard drives, one on each side of the fans.

Enterprise level hard disk drives are recommended for use in Supermicro chassis and servers.

For information on recommended HDDs, visit the Supermicro Web site at

http://www.supermicro.com



DIMMA1

DIMMA2

(Blue Slot)

DIMMB2

(Blue Slot)

DIMMB1

CPU properly

installed

Load lever locked

into place.

FAN2

JP9

SW1

T-SGPIO1

JSTBY1

JIPMB1

JPW2

JSD1

LED3

LED2

JD1

LED5

LED1

JPI2C1

BT1

JPW1

JTPM1

FANA

FAN3

FAN1

FAN2

FAN4

JPL1

JPL2

JPME2

JWD1

JPG1

JBR1

JPME1

J19

J18

JVR1

JI2C1

JI2C2

JOH1

JP8

JL1

JP2

JP1

JP7

USB 3.0-0

USB 3.0-1

USB 3.0-2/3

VGA

LAN2

LAN1

USB4/5

USB6/7

IPMI_LAN

COM2

COM1

P1-DIMMB1

P1-DIMMB2

P1-DIMMA2

P1-DIMMA1

PCH SLOT4 PCI-E 2.0 X4(IN X8)

CPU SLOT5 PCI-E 3.0 X8

CPU SLOT6 PCI-E 3.0 X8(IN X16)

JF1

I-SATA4

I-SATA3

I-SATA5 I-SATA2

I-SATA1

I-SATA0

USB8/9

JRK1

T-SGPIO2

JPB1

X10SLL-F

BMC FW

FP Control

PCH

BMC

CTRL

CPU

SP1

LED4

IPMI Code

BAR Code

MAC Code

JBT1

BIOS



ÌMNL-1456-QRG#Î

Beep Code

Polpulating these DIMM modules with a pair of memory modulesof the same type and same size wil result

in interleaved memory, which will improve memory performance

Notches

Release Tabs

Press Both Notches

Straight Down into the

Memory Slot