SUPER SUPERSERVER 5015A-PHF USER’S MANUAL Revision 1.
The information in this User’s Manual has been carefully reviewed and is believed to be accurate. The vendor assumes no responsibility for any inaccuracies that may be contained in this document, makes no commitment to update or to keep current the information in this manual, or to notify any person or organization of the updates. Please Note: For the most up-to-date version of this manual, please see our web site at www.supermicro.com. Super Micro Computer, Inc.
Preface Preface About This Manual This manual is written for professional system integrators and PC technicians. It provides information for the installation and use of the SuperServer 5015A-PHF. Installation and maintainance should be performed by experienced technicians only. The SuperServer 5015A-PHF is a single processor 1U mini rackmount server based on the SC502L-200B server chassis and the Intel® Atom™ X7SPA-HF motherboard.
SUPERSERVER 5015A-PHF User's Manual Chapter 5: Advanced Motherboard Setup Chapter 5 provides detailed information on the X7SPA-HF motherboard, including the locations and functions of connectors, headers and jumpers. Refer to this chapter when adding or removing processors or main memory and when reconfiguring the motherboard. Chapter 6: Advanced Chassis Setup Refer to Chapter 6 for detailed information on the SC502L-200B 1U rackmount server chassis.
Preface Notes v
SUPERSERVER 5015A-PHF User's Manual Table of Contents Chapter 1 Introduction 1-1 Overview ......................................................................................................... 1-1 1-2 Motherboard Features ..................................................................................... 1-2 Processor ........................................................................................................ 1-2 Memory ...................................................................
Table of Contents NIC1 ................................................................................................................ 3-2 HDD................................................................................................................. 3-2 Power .............................................................................................................. 3-3 Chapter 4 Standardized Warning Statements for AC Systems 4-1 About Standardized Warning Statements ............................
SUPERSERVER 5015A-PHF User's Manual Power Button ............................................................................................ 5-10 Reset Button..............................................................................................5-11 Power Fail LED ........................................................................................5-11 Overheat/Fan Fail......................................................................................5-11 NIC2 (LAN2) LED ......................
Table of Contents 5-11 Onboard Indicators........................................................................................ 5-19 LAN1/2 LEDs............................................................................................ 5-19 5-12 SATA Ports .................................................................................................... 5-19 SATA Ports ............................................................................................... 5-19 5-13 Installing Software ...
SUPERSERVER 5015A-PHF User's Manual Notes x
Chapter 1: Introduction Chapter 1 Introduction 1-1 Overview The Supermicro SuperServer 5015A-PHF is a single processor, 1U rackmount server. The 5015A-PHF is comprised of two main subsystems: the SC502L-200B chassis and the X7SPA-HF motherboard. Please refer to our web site for information on operating systems that have been certified for use with the 5015A-PHF. In addition to the mainboard and chassis, various hardware components may have been included with the 5015A-PHF, as listed below.
SUPERSERVER 5015A-PHF User's Manual 1-2 Motherboard Features At the heart of the SuperServer 5015A-PHF lies the X7SPA-HF, a single processor, low-power motherboard based upon Intel's ICH9R chipset. Below are the main features of the X7SPA-HF. Processor The X7SPA-HF supports one Intel® Atom™ D510 Dual-core processor. The processor is embedded into the motherboard. Memory The X7SPA-HF has two DIMM slots that can support up to 4 GB of non-ECC DDR2-667 SO-DIMMs.
Chapter 1: Introduction Factory Option FROM BMC VGA Connector SODIMM 2 SODIMM 1 DDR2 667 Intel ATOM D510 SATA Port 4 SATA Port 3 SATA Port 5 SATA Port 2 SATA Port 6 SATA Port 1 12V DC PSU 4-PIN CONN ATX PSU 24PIN CONN DMI USB USB Vertical Header x3 CONN x1 (5Ports) USB Rear x2 Ports SATA GEN2 x6 PCI-E x16 Slot PCI-E x4 Intel ICH9R USB 2.
SUPERSERVER 5015A-PHF User's Manual 1-3 Server Chassis Features The following is a general outline of the main features of the SC502L-200B 1U mini rackmount server chassis. System Power The SC502L-200B chassis includes a single 200W power supply. SATA Subsystem The SC502L-200B chassis was designed to support one 3.5" or two 2.5" internal SATA drives (not hot-swappable). ATA/100 IDE drives can be alternately supported.
Chapter 1: Introduction 1-4 Contacting Supermicro Headquarters Address: Super Micro Computer, Inc. 980 Rock Ave. San Jose, CA 95131 U.S.A. Tel: +1 (408) 503-8000 Fax: +1 (408) 503-8008 Email: marketing@supermicro.com (General Information) support@supermicro.com (Technical Support) Web Site: www.supermicro.com Europe Address: Super Micro Computer B.V. Het Sterrenbeeld 28, 5215 ML 's-Hertogenbosch, The Netherlands Tel: +31 (0) 73-6400390 Fax: +31 (0) 73-6416525 Email: sales@supermicro.
SUPERSERVER 5015A-PHF User's Manual Notes 1-6
Chapter 2: Server Installation Chapter 2 Server Installation 2-1 Overview This chapter provides a quick setup checklist to get your SuperServer 5015A-PHF up and running. Following the steps in the order given should enable you to have the system operational within a minimal amount of time. This quick setup assumes that your 5015A-PHF system has come to you with the processor and memory preinstalled. If your system is not already fully integrated with a motherboard, processor, system memory etc.
SUPERSERVER 5015A-PHF User's Manual • This product is for installation only in a Restricted Access Location (dedicated equipment rooms, service closets, etc.). • This product is not suitable for use with visual display work place devices according to §2 of the the German Ordinance for Work with Visual Display Units. 2-4 Warnings and Precautions Rack Precautions • Ensure that the leveling jacks on the bottom of the rack are fully extended to the floor with the full weight of the rack resting on them.
Chapter 2: Server Installation Rack Mounting Considerations Ambient Operating Temperature If installed in a closed or multi-unit rack assembly, the ambient operating temperature of the rack environment may be greater than the ambient temperature of the room. Therefore, consideration should be given to installing the equipment in an environment compatible with the manufacturer’s maximum rated ambient temperature (Tmra).
SUPERSERVER 5015A-PHF User's Manual 2-4 Rack Mounting Instructions This section provides information on installing the SC502 chassis into a rack unit There are a variety of rack units on the market, which may mean the assembly procedure will differ slightly. You should also refer to the installation instructions that came with the rack unit you are using. Installing the Chassis into a Rack 1. Confirm that chassis includes the four mounting screws required to mount the chassis into a rack 2.
Chapter 2: Server Installation Installing into a Telco Rack The SC502 supports Telco Rack installation. The SC502 chassis compact design allows the chassis to be installed into a Telco rack without the use of rails. Installing the Chassis into a Telco Rack 1. Confirm that chassis includes the four mounting screws required to mount the chassis into a rack 2. Align the thru holes of the chassis with the thru holes of the rack. 3.
SUPERSERVER 5015A-PHF User's Manual 2-5 Checking the Motherboard Setup After you install the 5015A-PHF in the rack, you will need to open the unit to make sure the motherboard is properly installed and all the connections have been made. Accessing the Inside of the System (Figure 2-3) 1. First, grasp the two handles on either side and pull the unit straight out until it locks (you will hear a "click"). 2. Remove the five screws that hold the chassis cover in place.
Chapter 2: Server Installation 12 13 12 12 Figure 2-3.
SUPERSERVER 5015A-PHF User's Manual 2-6 Checking the Drive Bay Setup Next, you should check to make sure the drives have been properly installed and all essential connections have been made. Checking the Drives 1. Refer to Chapter 6 if you need to reinstall a DVD-ROM drive to the system. 2. Depending upon your system's configuration, your system may have one or two Serial ATA drives already installed. If you need to install Serial ATA drives, please refer to the appropriate section in Chapter 6.
Chapter 3: System Interface Chapter 3 System Interface 3-1 Overview There are several LEDs on the control panel to keep you constantly informed of the overall status of the system as well as the activity and health of specific components. There are also two buttons on the control panel. This chapter explains the meanings of all LED indicators and the appropriate response you may need to take.
SUPERSERVER 5015A-PHF User's Manual Overheat When this LED is on it indicates an overheat condition, which may be caused by cables obstructing the airflow in the system or the ambient room temperature being too warm. Check the routing of the cables and make sure all fans are present and operating normally. You should also check to make sure that the chassis covers are installed. Finally, verify that the heatsinks are installed properly (see Chapter 5).
Chapter 3: System Interface Power Indicates power is being supplied to the system's power supply units. This LED should normally be illuminated when the system is operating.
SUPERSERVER 5015A-PHF User's Manual Notes 3-4
Chapter 4: Warning Statements for AC Systems Chapter 4 Standardized Warning Statements for AC Systems 4-1 About Standardized Warning Statements The following statements are industry standard warnings, provided to warn the user of situations which have the potential for bodily injury. Should you have questions or experience difficulty, contact Supermicro's Technical Support department for assistance. Only certified technicians should attempt to install or configure components.
SUPERSERVER 5015A-PHF User's Manual Warnung WICHTIGE SICHERHEITSHINWEISE Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut.
Warning Statements for AC Systems . ﺗﺤﺬﻳﺮ!ﻫﺬﺍ ﺍﻟﺮﻣﺰ ﻳﻌﻨﻲ ﺧﻄﺮ ﺍﻧﻚ ﻓﻲ ﺣﺎﻟﺔ ﻳﻤﻜﻦ ﺃﻥ ﺗﺘﺴﺒﺐ ﻓﻲ ﺍﺻﺎﺑﺔ ﺟﺴﺪﻳﺔ ﻛﻦ ﻋﻠﻰ ﻋﻠﻢ ﺑﺎﻟﻤﺨﺎﻁﺮ ﺍﻟﻨﺎﺟﻤﺔ ﻋﻦ ﺍﻟﺪﻭﺍﺋﺮ،ﻗﺒﻞ ﺃﻥ ﺗﻌﻤﻞ ﻋﻠﻰ ﺃﻱ ﻣﻌﺪﺍﺕ ﺍﻟﻜﻬﺮﺑﺎﺋﻴﺔ ﻭﻛﻦ ﻋﻠﻰ ﺩﺭﺍﻳﺔ ﺑﺎﻟﻤﻤﺎﺭﺳﺎﺕ ﺍﻟﻮﻗﺎﺋﻴﺔ ﻟﻤﻨﻊ ﻭﻗﻮﻉ ﺃﻱ ﺣﻮﺍﺩﺙ ﺍﺳﺘﺨﺪﻡ ﺭﻗﻢ ﺍﻟﺒﻴﺎﻥ ﺍﻟﻤﻨﺼﻮﺹ ﻓﻲ ﻧﻬﺎﻳﺔ ﻛﻞ ﺗﺤﺬﻳﺮ ﻟﻠﻌﺜﻮﺭ ﺗﺮﺟﻤﺘﻬﺎ 안전을 위한 주의사항 경고! 이 경고 기호는 위험이 있음을 알려 줍니다. 작업자의 신체에 부상을 야기 할 수 있는 상태에 있게 됩니다. 모든 장비에 대한 작업을 수행하기 전에 전기회로와 관련된 위험요소들을 확인하시고 사전에 사고를 방지할 수 있도록 표준 작업절차를 준수해 주시기 바랍니다.
SUPERSERVER 5015A-PHF User's Manual Installation Instructions Warning! Read the installation instructions before connecting the system to the power source. 設置手順書 システムを電源に接続する前に、設置手順書をお読み下さい。 警告 将此系统连接电源前,请先阅读安装说明。 警告 將系統與電源連接前，請先閱讀安裝說明。 Warnung Vor dem Anschließen des Systems an die Stromquelle die Installationsanweisungen lesen. ¡Advertencia! Lea las instrucciones de instalación antes de conectar el sistema a la red de alimentación.
Chapter 4: Warning Statements for AC Systems Circuit Breaker Warning! This product relies on the building's installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: 250 V, 20 A.
SUPERSERVER 5015A-PHF User's Manual 경고! 이 제품은 전원의 단락(과전류)방지에 대해서 전적으로 건물의 관련 설비에 의존합니다. 보호장치의 정격이 반드시 250V(볼트), 20A(암페어)를 초과하지 않도록 해야 합니다. Waarschuwing Dit product is afhankelijk van de kortsluitbeveiliging (overspanning) van uw electrische installatie. Controleer of het beveiligde aparaat niet groter gedimensioneerd is dan 220V, 20A.
Chapter 4: Warning Statements for AC Systems ¡Advertencia! El sistema debe ser disconnected de todas las fuentes de energía y del cable eléctrico quitado de los módulos de fuente de alimentación antes de tener acceso el interior del chasis para instalar o para quitar componentes de sistema. Attention Le système doit être débranché de toutes les sources de puissance ainsi que de son cordon d'alimentation secteur avant d'accéder à l'intérieur du chassis pour installer ou enlever des composants de systéme.
SUPERSERVER 5015A-PHF User's Manual Equipment Installation Warning! Only trained and qualified personnel should be allowed to install, replace, or service this equipment. 機器の設置 トレーニングを受け認定された人だけがこの装置の設置、交換、 またはサービスを許可 されています。 警告 只有经过培训且具有资格的人员才能进行此设备的安装、更换和维修。 警告 只有經過受訓且具資格人員才可安裝、更換與維修此設備。 Warnung Das Installieren, Ersetzen oder Bedienen dieser Ausrüstung sollte nur geschultem, qualifiziertem Personal gestattet werden.
Chapter 4: Warning Statements for AC Systems Waarschuwing Deze apparatuur mag alleen worden geïnstalleerd, vervangen of hersteld door geschoold en gekwalificeerd personeel. Restricted Area Warning! This unit is intended for installation in restricted access areas. A restricted access area can be accessed only through the use of a special tool, lock and key, or other means of security. (This warning does not apply to workstations).
SUPERSERVER 5015A-PHF User's Manual אזור עם גישה מוגבלת !אזהרה הגישה ניתנת בעזרת.יש להתקין את היחידה באזורים שיש בהם הגבלת גישה .(' מנעול וכד,כלי אבטחה בלבד )מפתח . ﺗﻢ ﺗﺨﺼﻴﺺ ﻫﺬﻩ ﺍﻟﻮﺣﺪﺓ ﻟﺘﺮﻛﻴﺒﻬﺎ ﻓﻲ ﻣﻨﺎﻁﻖ ﻣﺤﻈﻮﺭﺓ ،ﻳﻤﻜﻦ ﺍﻟﻮﺻﻮﻝ ﺇﻟﻰ ﻣﻨﻄﻘﺔ ﻣﺤﻈﻮﺭﺓ ﻓﻘﻂ ﻣﻦ ﺧﻼﻝ ﺍﺳﺘﺨﺪﺍﻡ ﺃﺩﺍﺓ ﺧﺎﺻﺔ ﻗﻔﻞ ﻭﻣﻔﺘﺎﺡ ﺃﻭ ﺃﻱ ﻭﺳﻴﻠﺔ ﺃﺧﺮﻯ ﻟﻼﻷﻣﺎﻥ 경고! 이 장치는 접근이 제한된 구역에 설치하도록 되어있습니다. 특수도구, 잠금 장치 및 키, 또는 기타 보안 수단을 통해서만 접근 제한 구역에 들어갈 수 있습니다. Waarschuwing Dit apparaat is bedoeld voor installatie in gebieden met een beperkte toegang.
Chapter 4: Warning Statements for AC Systems Warnung Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr. Ersetzen Sie die Batterie nur durch den gleichen oder vom Hersteller empfohlenen Batterietyp. Entsorgen Sie die benutzten Batterien nach den Anweisungen des Herstellers. Attention Danger d'explosion si la pile n'est pas remplacée correctement. Ne la remplacer que par une pile de type semblable ou équivalent, recommandée par le fabricant.
SUPERSERVER 5015A-PHF User's Manual Redundant Power Supplies Warning! This unit might have more than one power supply connection. All connections must be removed to de-energize the unit. 冗長電源装置 このユニットは複数の電源装置が接続されている場合があります。 ユニットの電源を切るためには、すべての接続を取り外さなければなりません。 警告 此部件连接的电源可能不止一个，必须将所有电源断开才能停止给该部件供电。 警告 此裝置連接的電源可能不只一個，必須切斷所有電源才能停止對該裝置的供電。 Warnung Dieses Gerät kann mehr als eine Stromzufuhr haben. Um sicherzustellen, dass der Einheit kein trom zugeführt wird, müssen alle Verbindungen entfernt werden.
Chapter 4: Warning Statements for AC Systems .ﻗﺪ ﻳﻜﻮﻥ ﻟﻬﺬﺍ ﺍﻟﺠﻬﺎﺯ ﻋﺪﺓ ﺍﺗﺼﺎﻻﺕ ﺑﻮﺣﺪﺍﺕ ﺍﻣﺪﺍﺩ ﺍﻟﻄﺎﻗﺔ ﻳﺠﺐ ﺇﺯﺍﻟﺔ ﻛﺎﻓﺔ ﺍﻻﺗﺼﺎﻻﺕ ﻟﻌﺰﻝ ﺍﻟﻮﺣﺪﺓ ﻋﻦ ﺍﻟﻜﻬﺮﺑﺎء 경고! 이 장치에는 한 개 이상의 전원 공급 단자가 연결되어 있을 수 있습니다. 이 장치에 전원을 차단하기 위해서는 모든 연결 단자를 제거해야만 합니다. Waarschuwing Deze eenheid kan meer dan één stroomtoevoeraansluiting bevatten. Alle aansluitingen dienen verwijderd te worden om het apparaat stroomloos te maken. Backplane Voltage Warning! Hazardous voltage or energy is present on the backplane when the system is operating.
SUPERSERVER 5015A-PHF User's Manual מתח בפנל האחורי !אזהרה יש להיזהר במהלך.קיימת סכנת מתח בפנל האחורי בזמן תפעול המערכת .העבודה ﻫﻨﺎﻙ ﺧﻄﺮ ﻣﻦ ﺍﻟﺘﻴﺎﺭ ﺍﻟﻜﻬﺮﺑﺎﺋﻲ ﺃﻭﺍﻟﻄﺎﻗﺔ ﺍﻟﻤﻮﺟﻮﺩﺓ ﻋﻠﻰ ﺍﻟﻠﻮﺣﺔ ﻋﻨﺪﻣﺎ ﻳﻜﻮﻥ ﺍﻟﻨﻈﺎﻡ ﻳﻌﻤﻞ ﻛﻦ ﺣﺬﺭﺍ ﻋﻨﺪ ﺧﺪﻣﺔ ﻫﺬﺍ ﺍﻟﺠﻬﺎﺯ 경고! 시스템이 동작 중일 때 후면판 (Backplane)에는 위험한 전압이나 에너지가 발생 합니다. 서비스 작업 시 주의하십시오. Waarschuwing Een gevaarlijke spanning of energie is aanwezig op de backplane wanneer het systeem in gebruik is. Voorzichtigheid is geboden tijdens het onderhoud.
Chapter 4: Warning Statements for AC Systems Attention L'équipement doit être installé conformément aux normes électriques nationales et locales. תיאום חוקי החשמל הארצי !אזהרה .התקנת הציוד חייבת להיות תואמת לחוקי החשמל המקומיים והארציים ﺗﺮﻛﻴﺐ ﺍﻟﻤﻌﺪﺍﺕ ﺍﻟﻜﻬﺮﺑﺎﺋﻴﺔ ﻳﺠﺐ ﺃﻥ ﻳﻤﺘﺜﻞ ﻟﻠﻘﻮﺍﻧﻴﻦ ﺍﻟﻤﺤﻠﻴﺔ ﻭﺍﻟﻮﻁﻨﻴﺔ ﺍﻟﻤﺘﻌﻠﻘﺔ ﺑﺎﻟﻜﻬﺮﺑﺎء 경고! 현 지역 및 국가의 전기 규정에 따라 장비를 설치해야 합니다. Waarschuwing Bij installatie van de apparatuur moet worden voldaan aan de lokale en nationale elektriciteitsvoorschriften.
SUPERSERVER 5015A-PHF User's Manual ¡Advertencia! Al deshacerse por completo de este producto debe seguir todas las leyes y reglamentos nacionales. Attention La mise au rebut ou le recyclage de ce produit sont généralement soumis à des lois et/ou directives de respect de l'environnement. Renseignez-vous auprès de l'organisme compétent. סילוק המוצר !אזהרה .
Chapter 4: Warning Statements for AC Systems 警告 當您從機架移除風扇裝置，風扇可能仍在轉動。小心不要將手指、螺絲起子和其他 物品太靠近風扇。 Warnung Die Lüfter drehen sich u. U. noch, wenn die Lüfterbaugruppe aus dem Chassis genommen wird. Halten Sie Finger, Schraubendreher und andere Gegenstände von den Öffnungen des Lüftergehäuses entfernt. ¡Advertencia! Los ventiladores podran dar vuelta cuando usted quite ell montaje del ventilador del chasis.
SUPERSERVER 5015A-PHF User's Manual Power Cable and AC Adapter Warning! When installing the product, use the provided or designated connection cables, power cables and AC adaptors. Using any other cables and adaptors could cause a malfunction or a fire. Electrical Appliance and Material Safety Law prohibits the use of UL or CSA -certified cables (that have UL/CSA shown on the code) for any other electrical devices than products designated by Supermicro only.
Chapter 4: Warning Statements for AC Systems Attention Lors de l'installation du produit, utilisez les bables de connection fournis ou désigné. L'utilisation d'autres cables et adaptateurs peut provoquer un dysfonctionnement ou un incendie. Appareils électroménagers et de loi sur la sécurité Matériel interdit l'utilisation de UL ou CSA câbles certifiés qui ont UL ou CSA indiqué sur le code pour tous les autres appareils électriques que les produits désignés par Supermicro seulement.
SUPERSERVER 5015A-PHF User's Manual Notes 4-20
Chapter 5: Advanced Motherboard Setup Chapter 5 Advanced Motherboard Setup This chapter covers the steps required to install the X7SPA-HF motherboard into the chassis, connect the data and power cables and install add-on cards. All motherboard jumpers and connections are also described. A layout and quick reference chart are included in this chapter for your reference. Remember to completely close the chassis when you have finished working with the motherboard to better cool and protect the system.
SUPERSERVER 5015A-PHF User's Manual Unpacking The motherboard is shipped in antistatic packaging to avoid electrical static discharge. When unpacking the board, make sure the person handling it is static protected. 5-2 Motherboard Installation This section explains the first step of physically mounting the X7SPA-HF into the SC502L-200B chassis. Following the steps in the order given will eliminate the most common problems encountered in such an installation.
Chapter 5: Advanced Motherboard Setup 5-3 Connecting Cables Now that the motherboard is installed, the next step is to connect the cables to the board. These include the data cables for the peripherals and control panel and the power cables. Connecting Data Cables The cables used to transfer data from the peripheral devices have been carefully routed to prevent them from blocking the flow of cooling air that moves through the system from front to back.
SUPERSERVER 5015A-PHF User's Manual Figure 5-1. Control Panel Header Pins 20 19 Ground NMI X X Power LED Vcc HDD LED Vcc NIC1 LED Vcc NIC2 LED Vcc OH/Fan Fail LED Vcc Power Fail LED Vcc Ground Ground 2 5-4 Reset Reset Button PWR Power Button 1 I/O Ports The I/O ports are color coded in conformance with the PC 99 specification. See Figure 5-2 below for the colors and locations of the various I/O ports. Figure 5-2. I/O Ports 2 4 1 3 5 6 Rear I/O Ports 1. Keyboard 5. COM1 2.
Chapter 5: Advanced Motherboard Setup 5-5 Onboard Processor The Intel Atom processor is soldered directly onto the motherboard. Installing and removing the processor is not required. A small active heatsink (with fan) sits on the processor to keep it cool. 5-6 Installing Memory Note: Check the Supermicro web site for recommended memory modules. CAUTION Exercise extreme care when installing or removing DIMM modules to prevent any possible damage. DIMM Installation 1.
SUPERSERVER 5015A-PHF User's Manual Figure 5-3. DIMM Installation 1. Position the SO-DIMM module's bottom key so that it aligns with the receptive point on the slot. 2. Insert the SO-DIMM module vertically at about a 45 degree angle. 3. Press down until the module locks into place. The side clips will automatically secure the SO DIMM module, locking it into place. 4. To Remove: Use your thumbs to gently push the side clips near both ends away from the module. This should release it from the slot.
Chapter 5: Advanced Motherboard Setup 5-7 Adding PCI Expansion Cards The SC502L-200B chassis can accommodate one full-height, half-length PCI expansion card. Installing an Expansion Card 1. After powering down the system, remove the PCI slot shield. 2. Fully seat the card into the slot, pushing down with your thumbs evenly on both sides of the card. 3. Finish by using a screw to secure the top of the card shield to the chassis.
SUPERSERVER 5015A-PHF User's Manual 5-8 Motherboard Details Figure 5-4.
Chapter 5: Advanced Motherboard Setup 44 JBT1 CMOS Clear (See Section 5-9) 46 J12/J13* DCD/P5V Select (COM3/COM4) Pins 1-2 (DCD ) 47 J10/J11* DCD/P5V Select (COM1/COM2) Pins 1-2 (DCD) 52 JPF Power Force On Open (Disabled) *OEM option.
SUPERSERVER 5015A-PHF User's Manual 5-9 Connector Definitions ATX Power 24-pin Connector Pin Definitions Pin# Definition Pin # Definition Main ATX Power Supply Connector 13 +3.3V 1 +3.3V 14 -12V 2 +3.3V The 24-pin main power connector 15 COM 3 COM (JPW1) is used to provide power to 16 PS_ON 4 +5V the motherboard. This power connector meets the SSI EPS 12V specifica- 17 COM 5 COM 18 COM 6 +5V tion. See the table on the right for pin 19 COM 7 COM definitions.
Chapter 5: Advanced Motherboard Setup Reset Button Reset Button Pin Definitions (JF1) The reset button (from the computer chassis) connects to pins 3 and 4 of JF1. See the table on the right for pin definitions. Pin# Definition 3 Reset 4 Ground Power Fail LED PWR Fail LED Pin Definitions (JF1) The Power Fail LED connection is located on pins 5 and 6 of JF1. Refer to the table on the right for pin definitions.
SUPERSERVER 5015A-PHF User's Manual Power LED The Power LED connector is located on pins 15 and 16 of JF1. This con- Power LED Pin Definitions (JF1) nection is used to provide LED indication of power being supplied to the system. See the table on the right for pin definitions. NMI Button Pin# Definition 15 5V Stby 16 Control NMI Button Pin Definitions (JF1) The non-maskable interrupt button header is located on pins 19 and 20 of JF1. Refer to the table on the right for pin definitions.
Chapter 5: Advanced Motherboard Setup High Definition Front Panel Audio Front Panel Audio Header Pin # The Front Panel Audio header is used to connect the chassis' front panel Definition Pin # Definition 1 MC_L 6 Ground 2 AUD_GND 7 FP_Jack-Detect High Definition Audio (HDA) controls 3 MC_R 8 Key to the motherboard. See the table on 4 FP_Audio-Detect 9 Line_2_L the right for pin definitions.
SUPERSERVER 5015A-PHF User's Manual CD Header CD Header Pin Definitions A 4-pin CD header is located at CD1. This header allows you to use the on- Pin# Definition board sound for audio CD playback. 1 Left Stereo Signal Connect an audio cable from your 2 Ground 3 Ground 4 Right Stereo Signal CD drive to the header that fits your cable's connector. See the table at right for pin definitions.
Chapter 5: Advanced Motherboard Setup LVDS Pin Definitions Pin# Definition Pin Definition 1 3.3V 11 3.3V An LVDS connector (J5) is available on the X7SPA-L only. This connector 2 LDATAP0 12 LDATAN0 3 GND 13 GND provides 18-bit LVDS (Low Voltage 4 LDATAP1 14 LDATAN1 Differential Signaling) for an LCD 5 GND 15 GND 6 LDATAP2 16 LDATAN2 7 GND 17 GND 8 NC 18 NC 9 LVDDEN 19 NC 10 LCLKP 20 LCLKN LVDS Connector panel or other similar devices.
SUPERSERVER 5015A-PHF User's Manual 5-10 Jumper Settings Explanation of Jumpers To modify the operation of the motherboard, jumpers can be used to choose between optional settings. Jumpers 3 2 1 3 2 1 Connector Pins create shorts between two pins to change the function of the connector. Pin 1 is identified with a square solder Jumper pad on the printed circuit board. See the motherboard layout pages for jumper locations.
Chapter 5: Advanced Motherboard Setup SMB (I2C) Bus to PCI Slots I2C to PCI-Slots Jumper Settings Jumpers JI2C1 and JI2C2 allow you to connect the System Management Bus (SMB) to the PCI-E PCI slot. The default setting is Disabled. See table Jumper Definition On Enabled Off Disabled on the right for jumper settings. TPM Support Enable JPT1 allows the user to enable TPM (Trusted Platform Module) support to enhance data integrity and system security. See the table on the right for jumper settings.
SUPERSERVER 5015A-PHF User's Manual DCD / P5V Select Jumpers J10~J13 allow selection between the standard Data Carrier Detect (DCD) modem signal or the system voltage +5V on pin 1 of the COM1~COM4 ports This is an OEM option only. DCD / P5V Select Jumper Settings Jumper Setting Pins 1-2 DCD Pins 2-3 P5V HDA/AC97 Select JL2 allows the user to select between High Definition Audio (HDA) or legacy AC97 audio. The default setting is HD Audio.
Chapter 5: Advanced Motherboard Setup 5-11 Onboard Indicators LAN1/2 LED (Connection Speed Indicator) LAN1/2 LEDs The Ethernet ports (located beside the VGA port) have two LEDs. On each port, the yellow LED indicates activity LED Color Definition Off No Connection or 10 Mb/s Green 100 Mb/s Amber 1 Gb/s while the other LED may be green, amber or off to indicate the speed of the connection. See the table on the right for the indication associated with the connection speed LED.
SUPERSERVER 5015A-PHF User's Manual 5-13 Installing Software The Supermicro ftp site contains drivers and utilities for your system at ftp://ftp. supermicro.com. Some of these must be installed, such as the chipset driver. After accessing the ftp site, go into the CDR_Images directory and locate the ISO file for your motherboard. Download this file to create a CD/DVD of the drivers and utilities it contains. (You may also use a utility to extract the ISO file if preferred.
Chapter 5: Advanced Motherboard Setup SuperDoctor III The SuperDoctor® III program is a web-based management tool that supports remote management capability. It includes Remote and Local Management tools. The local management is called SD III Client. The SuperDoctor III program allows you to monitor the environment and operations of your system. SuperDoctor III displays crucial system information such as CPU temperature, system voltages and fan status.
SUPERSERVER 5015A-PHF User's Manual Figure 5-7. SuperDoctor III Interface Display Screen (Remote Control) 5-13 Onboard Battery Care must be taken to assure that the chassis cover is in place when the 6017RTDLF is operating to assure proper cooling. Out of warranty damage to the system can occur if this practice is not strictly followed. Figure 5-8. Installing the Onboard Battery Please handle used batteries carefully.
Chapter 6: Advanced Chassis Setup Chapter 6 Advanced Chassis Setup This chapter covers the steps required to install components and perform maintenance on the SC502L chassis. For component installation, follow the steps in the order given to eliminate the most common problems encountered. If a step is unnecessary, skip ahead to the step that follows. Tools Required The only tool you will need to install components and perform maintenance is a Philips screwdriver.
SUPERSERVER 5015A-PHF User's Manual Figure 6-1. Chassis Front View Control Panel Figure 6-2. Chassis Rear View Power Supply Mouse/Keyboard USB Ports 6-2 COM Port Ethernet Ports PCI Slot VGA Port Control Panel The control panel (located on the front of the chassis) must be connected to the JF1 connector on the serverboard to provide you with system control buttons and status indicators. These wires have been bundled together in a ribbon cable to simplify the connection.
Chapter 6: Advanced Chassis Setup 6-3 System Fans The SC502L is a fan-less chassis, which results in extremely quiet and energyefficient operation. The only fan in the system is located on the heatsink for the embedded processor. 6-4 Drive Bay Installation/Removal Installling a 3.5" SATA Drive (Figure 6-3) 1. Power down the system and unplug the AC power cord. 2. Remove the chassis cover as described on page 2-6. 3.
SUPERSERVER 5015A-PHF User's Manual The 3.5" hard drive screws directly into the chassis Figure 6-3. Installing a 3.5" Hard Drive The 2.5" hard drives (1) must be installed in the bracket (2) before they are screwed into the chassis. 1 12 Figure 6-4. Installing 2.
Chapter 6: Advanced Chassis Setup 6-5 Power Supply The SC502L-200B chassis has a single 200 watt power supply. This power supply is auto-switching capable. This enables it to automatically sense and operate at a 100v to 240v input voltage. In the event that the power supply unit fails, the system will shut down and you will need to change the power supply unit. New units can be ordered directly from Supermicro (see contact information in the Preface). Replacing the Power Supply (Figure 6-5) 1.
SUPERSERVER 5015A-PHF User's Manual Rear Mounting Screws Power Supply Mounting Thru Holes Bottom Mounting Screws Figure 6-5.
Chapter 7: BIOS Chapter 7 BIOS 7-1 Introduction This chapter describes the AMI BIOS Setup Utility for the X7SPA-HF. The AMI ROM BIOS is stored in a Flash EEPROM and can be easily updated. This chapter describes the basic navigation of the AMI BIOS Setup Utility setup screens. Note: For instructions on BIOS recovery, please refer to the instruction guide posted at http://www.supermicro.com/support/manuals/.
SUPERSERVER 5015A-PHF User's Manual How to Start the Setup Utility Normally, the only visible Power-On Self-Test (POST) routine is the memory test. As the memory is being tested, press the key to enter the main menu of the AMI BIOS Setup Utility. From the main menu, you can access the other setup screens. An AMI BIOS identification string is displayed at the left bottom corner of the screen, below the copyright message. Warning! Do not upgrade the BIOS unless your system has a BIOS-related issue.
Chapter 7: BIOS System Overview: The following BIOS information will be displayed: System Time/System Date Use this option to change the system time and date. Highlight System Time or System Date using the arrow keys. Enter new values through the keyboard. Press the key or the arrow keys to move between fields. The date must be entered in Day MM/DD/YY format. The time is entered in HH:MM:SS format. (Note: The time is in the 24-hour format. For example, 5:30 P.M. appears as 17:30:00.
SUPERSERVER 5015A-PHF User's Manual 7-3 Advanced Setup Configurations Use the arrow keys to select Boot Setup and hit to access the submenu items: BOOT Feature Quick Boot If Enabled, this option will skip certain tests during POST to reduce the time needed for system boot. The options are Enabled and Disabled. Quiet Boot This option allows the bootup screen options to be modified between POST messages or the OEM logo. Select Disabled to display the POST messages.
Chapter 7: BIOS Bootup Num-Lock This feature selects the Power-on state for Numlock key. The options are Off and On. PS/2 Mouse Support This feature enables support for the PS/2 mouse. The options are Disabled, Enabled and Auto. Wait For 'F1' If Error This forces the system to wait until the 'F1' key is pressed if an error occurs. The options are Disabled and Enabled. Hit 'Del' Message Display This feature displays "Press DEL to run Setup" during POST. The options are Enabled and Disabled.
SUPERSERVER 5015A-PHF User's Manual Standby Power in S5 This feature supplies standby power while in S5 (sleep mode). Set this feature to Disabled to comply with EuP requirements, Enable this feature to activate wake-up capability while in sleep mode. The options are Enabled and Disabled. CPU Configuration Warning: Take Caution when changing the Advanced settings. An incorrect value, a very high DRAM frequency or incorrect DRAM timing may cause system to become unstable.
Chapter 7: BIOS Advanced Chipset Control The items included in the Advanced Settings submenu are listed below. Northbridge Configuration DRAM Frequency This option allows the user to select the desired frequency setting for the onboard memory modules. The options are Auto, 667 MHz and 800 MHz. Configure DRAM Timing by SPD This option allows the user to select the desired DRAM timing for the onboard memory modules. The options are Enabled and Disabled.
SUPERSERVER 5015A-PHF User's Manual Active State Power Management Select Enabled to start Active-State Power Management for signal transactions between L0 and L1 Links on the PCI Express Bus. This maximizes power-saving and transaction speed. The options are Enabled and Disabled. Reserved Page Route This feature allows the user to decide which bus to send debug information to. The options are Disabled, PCI and LPC.
Chapter 7: BIOS SATA#2 Configuration (Available if IDE is enabled under "Configure SATA#1 as" above) Selecting Enhanced will set SATA#2 to native SATA mode. The options are Disabled and Enhanced IDE Detect Timeout (sec) Use this feature to set the time-out value for the BIOS to detect the ATA, ATAPI devices installed in the system. The options are 0 (sec), 5, 10, 15, 20, 25, 30, and 35.
SUPERSERVER 5015A-PHF User's Manual Select Auto to allow the AMI BIOS to automatically detect the PIO mode. Use this value if the IDE disk drive support cannot be determined. Select 0 to allow the AMI BIOS to use PIO mode 0. It has a data transfer rate of 3.3 MBs. Select 1 to allow the AMI BIOS to use PIO mode 1. It has a data transfer rate of 5.2 MBs. Select 2 to allow the AMI BIOS to use PIO mode 2. It has a data transfer rate of 8.3 MBs. Select 3 to allow the AMI BIOS to use PIO mode 3.
Chapter 7: BIOS Select UDMA4 to allow the BIOS to use Ultra DMA mode 4 . It has a data transfer rate of 100 MBs. The options are Auto, SWDMAn, MWDMAn, and UDMAn. S.M.A.R.T. For Hard disk drives Self-Monitoring Analysis and Reporting Technology (SMART) can help predict impending drive failures. Select Auto to allow the AMI BIOS to automatically detect hard disk drive support. Select Disabled to prevent the AMI BIOS from using the S.M.A.R.T. Select Enabled to allow the AMI BIOS to use the S.M.A.R.T.
SUPERSERVER 5015A-PHF User's Manual PCI Slot 1 Use this feature to enable or disable PCI slot Option ROMs. The options are Disabled and Enabled. Load Onboard LAN 1 Option ROM/ Load Onboard LAN 2 Option ROM Select Enabled to load the onboard LAN Option ROM for the LAN port as specified. The options are Enabled and Disabled. Initiate Graphics Adapter Use this feature to select the graphics controller to be used as the primary boot device. The options are Other, Onboard VGA and Slot 6.
Chapter 7: BIOS Flow Control This feature allows the user to set the flow control for Console Redirection. The options are None, Hardware, and Software. Redirection After BIOS POST Select Disabled to turn off Console Redirection after Power-On Self-Test (POST). Select Always to keep Console Redirection active all the time after POST. (Note: This setting may not be supported by some operating systems.) Select Boot Loader to keep Console Redirection active during POST and Boot Loader.
SUPERSERVER 5015A-PHF User's Manual Hardware Health Configuration This feature allows the user to monitor Hardware Health of the system and review the status of each item when displayed. CPU Overheat Alarm This option allows the user to select the CPU Overheat Alarm setting which determines when the CPU OH alarm will be activated to provide warning of possible CPU overheat.
Chapter 7: BIOS User intervention: No action is required. However, consider checking the CPU fans and the chassis ventilation for blockage. High – The processor is running hot. This is a ‘caution’ level since the CPU’s ‘Temperature Tolerance’ has been reached (or has been exceeded) and may activate an overheat alarm: The Default Alarm – the Overheat LED and system buzzer will activate if the High condition continues for some time after it is reached.
SUPERSERVER 5015A-PHF User's Manual Fan Speed Control Modes This feature allows the user to decide how the system controls the speeds of the onboard fans. The CPU temperature and the fan speed are correlative. When the CPU on-die temperature increases, the fan speed will also increase for effective system cooling. Select Full Speed to allow the onboard fans to run at full speed (of 100% Pulse Width Modulation Duty Cycle) for maximum cooling.
Chapter 7: BIOS ACPI Aware O/S Enable ACPI support if it is supported by the OS to control ACPI through the Operating System. Otherwise, disable this feature. The options are Yes and No. Suspend Mode This setting allows you to configure the ACPI (Advanced Configuration and Power Interface) state for your system when it is in the Suspend mode. The options are S1, S3 and Auto.
SUPERSERVER 5015A-PHF User's Manual IPMI Configuration (X7SPA-HF Only) Intelligent Platform Management Interface (IPMI) is a set of common interfaces that IT administrators can use to monitor system health and to manage the system as a whole. For more information on the IPMI specifications, please visit Intel's website at www.intel.com. Note: For this particular motherboard, IPMI shares the same network interface with LAN1. IPMI Firmware Revision This item displays the current IPMI firmware revision.
Chapter 7: BIOS IP Address - Enter the IP address for this machine. This should be in decimal and in dotted quad form (i.e., 192.168.10.253). The value of each three-digit number separated by dots should not exceed 255. Subnet Mask - Subnet masks tell the network which subnet this machine belongs to. The value of each three-digit number separated by dots should not exceed 255 (i.e., 255.255.255.0). Gateway Address - Enter the Gateway address this machine will use (i.e., 192.168.10.1).
SUPERSERVER 5015A-PHF User's Manual 7-4 Security Settings The AMI BIOS provides a Supervisor and a User password. If you use both passwords, the Supervisor password must be set first. Supervisor Password This item indicates if a supervisor password has been entered for the system. Clear means such a password has not been used and Set means a supervisor password has been entered for the system. User Password: This item indicates if a user password has been entered for the system.
Chapter 7: BIOS Change User Password Select this feature and press to access the submenu , and then type in a new User Password. Clear User Password (Available only if User Password has been set) Password Check Available options are Setup and Always. Boot Sector Virus Protection When Enabled, the AMI BOIS displays a warning when any program (or virus) issues a Disk Format command or attempts to write to the boot sector of the hard disk drive. The options are Enabled and Disabled.
SUPERSERVER 5015A-PHF User's Manual 7-5 Boot Settings Use this feature to configure Boot Settings: Boot Device Priority This feature allows the user to specify the sequence of priority for the Boot Device. The settings are 1st boot device, 2nd boot device, 3rd boot device, 4th boot device, 5th boot device and Disabled.
Chapter 7: BIOS Removable Drives This feature allows the user to specify the boot sequence from available Removable Drives. The settings are 1st boot device, 2nd boot device, and Disabled. • 1st Drive • 2nd Drive - [USB: XXXXXXXXX] Retry Boot Devices Select this option to retry booting from the configured boot devices if the systems fail to boot initially. The options are Disabled and Enabled.
SUPERSERVER 5015A-PHF User's Manual figuration parameters can take effect. Select Save Changes and Exit from the Exit menu and press . Discard Changes and Exit Select this option to quit the BIOS Setup without making any permanent changes to the system configuration, and reboot the computer. Select Discard Changes and Exit from the Exit menu and press . Discard Changes Select this option and press to discard all the changes and return to the AMI BIOS Utility Program.
Appendix A: POST Error Beep Codes Appendix A POST Error Beep Codes This section lists POST (Power On Self Test) error beep codes for the AMI BIOS. POST error beep codes are divided into two categories: recoverable and terminal. This section lists Beep Codes for recoverable POST errors. Recoverable POST Error Beep Codes When a recoverable type of error occurs during POST, BIOS will display a POST code that describes the problem.
SUPERSERVER 5015A-PHF User's Manual Notes A-2
Appendix B: System Specifications Appendix B System Specifications Processors Embedded single Intel® Atom™ D510 dual-core processor Chipset Intel ICH9R chipset BIOS 32 Mb AMI SPI Flash Memory Capacity Two DIMM slots that can support up to 4 GB of unbuffered non-ECC DDR2667 SO-Dimms Note: See the memory section in Chapter 5 for details. SATA Controller On-chip (ICH9R) 3 Gb/s Intel SATA controller Hard Drive Support Up to two internal 2.5" drives or one internal 3.
SUPERSERVER 5015A-PHF User's Manual System Input Requirements AC Input Voltage: 100-240 VAC (auto-range) Rated Input Current: 3A max. Rated Input Frequency: 50 to 60 Hz Power Supply Rated Output Power: 200W (Part# PWS-202-1H) Rated Output Voltages: +3.3V (8A), +5V (8A), +12V (16A), -12V (0.
Appendix B: System Specifications Notes B-3
SUPERSERVER 5015A-PHF User's Manual (continued from front) The products sold by Supermicro are not intended for and will not be used in life support systems, medical equipment, nuclear facilities or systems, aircraft, aircraft devices, aircraft/emergency communication devices or other critical systems whose failure to perform be reasonably expected to result in significant injury or loss of life or catastrophic property damage.
