Quick reference (3.0)

ManualsBrandsSupermicro ManualsServerSS1027TR-TFF

http://www.supermicro.com

MNL-1414-QRG

Board Layout

SuperServer 1027TR-TF/TQF/TFF Quick Reference Guide

Rear View

Hard Drive Signal

Hard Drive Fail

Power LED

Device Activity LED

LAN1 LED & LAN2 LED

Information LED

Power Button

UID Button

Description

No.

CPU Installation

Beep Codes

PCI Expansion Slot (w/riser card)

Dedicated LAN for IPMI

Power Supply Module

Description

No.

Front view & Interface



Heatsink Installation

1. Place heatsink on top of installed CPU

2. Line up the four screws to socket

3. Push down heatsink and screw down as shown

(cross pattern, in order: A, C, B, D)

4. NOTE: Only use 6-8 lb/f of torque; otherwise, hand-tighten

each screw, to avoid damaging the system

MEMORY

Caution

SAFETY INFORMATION

IMPORTANT: See installation instructions and safety warning

before connecting system to power supply.

http://www.supermicro.com/about/policies/safety_information.cfm

WARNING:

To reduce risk of electric shock/damage to equipment,

disconnect power from server by disconnecting all power

cords from electrical outlets.

If any CPU socket empty, install protective plastic CPU cap

CAUTION:

Always be sure all power supplies for this system have

the same power output. If mixed power supplies are

installed, the system will not operate.

Top View of DDR3 Slot

Release Tab

Note: Notch should align

with the receptive key

point on the slot.

Notch

Front View

Align CPU to socket;

install CPU straight down

For more information go to :

http://www.supermicro.com/support



NOTE:

Do not bend pin inside socket



Description

No.

P1-DIMMA1 slot

P1-DIMMB1 slot

P1-DIMMC1 slot

P1-DIMMD1 slot

P2-DIMME1 slot

P2-DIMMF1 slot

P2-DIMMG1 slot

P2-DIMMH1 slot

CPU1 (Install CPU1 first)

CPU2

I-SATA 3.0 (SATA 3.0 ports 0/1)

I-SATA 2.0 (SATA 2.0 ports 2~5)

JBT1 = CMOS Reset

JSD1 = SATA DOM Power

Note:

Install CPU1 first

X9DRT-F

CPU1 PCI-E 3.0 x16

JSD1

P1-DIMMA1

P1-DIMMB1

P2-DIMMH1

P2-DIMMG1

P2-DIMMF1

P2-DIMME1

P1-DIMMC1

P1-DIMMD1

JBT1

CPU2

CPU1

CPU1 PCI-E 3.0 x16 slot for SMC-Proprietary Riser Card

(Available when CPU1 is installed)

Processors and their Corresponding

Memory Modules

CPU# Corresponding DIMM Modules

CPU 1 P1-

DIMMA1

P1-

DIMMB1

P1-

DIMMC1

P1-

DIMMD1

CPU2 P2-

DIMME1

P2-

DIMMF1

P2-

DIMMG1

P2-

DIMMH1

Processor and Memory Module Population for Optimal Performance

Number of

CPUs+DIMMs

CPU and Memory Population Table

(For memory to work properly, follow the instructions below.)

1 CPU &

2 DIMMs

CPU1

P1-DIMMA1/P1-DIMMB1

1 CPU &

4 DIMMs

CPU1

P1-DIMMA1/P1-DIMMB1, P1-DIMMC1/P1-DIMMD1

2 CPUs &

4 DIMMs

CPU1 + CPU2

P1-DIMMA1/P1-DIMMB1, P2-DIMME1/P2-DIMMF1

2 CPUs &

6 DIMMs

CPU1 + CPU2

P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1

2 CPUs &

8 DIMMs

CPU1 + CPU2

P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1/P2-

DIMMG1/P2-DIMMH1

Installing UDIMM (ECC/Non-ECC) Memory

Intel E5-2600 Series Processor UDIMM Memory Support

Ranks Per DIMM &

Data Width

Memory Capacity

Per DIMM

(See the Note below)

Speed (MT/s) and Voltage Validated by Slot per

Channel (SPC) and DIMM Per Channel (DPC)

1 Slot Per Channel

1DPC

1.35V 1.5V

SRx8 Non-ECC 1GB 2GB 4GB NA 1066,1333, 1600

DRx8 Non-ECC 2GB 4GB 8GB NA 1066,1333, 1600

SRx16 Non-ECC 512MB 1GB 2GB NA 1066,1333, 1600

SRx8 ECC 1GB 2GB 4GB 1066, 1333 1066,1333, 1600

DRx8 ECC 2GB 4GB 8GB 1066, 1333 1066,1333, 1600

Note: For detailed information on memory support and updates, please refer to the SMC Recommended

Memory List posted on our website at http://www.supermicro.com/support/resources/mem.cfm.

Installing RDIMM (ECC) Memory

Intel E5-2600 Series Processor RDIMM Memory Support

Ranks Per

DIMM & Data

Width

Memory Capacity

Per DIMM

(See the Note Below)

1 Slot Per Channel

1DPC

1.35V 1.5V

SRx8 1GB 2GB 4GB 1066, 1333 1066, 1333,1600

DRx8 2GB 4GB 8GB 1066, 1333 1066,1333, 1600

SRx4 2GB 4GB 8GB 1066, 1333 1066,1333, 1600

DRx4 4GB 8GB 16GB 1066, 1333 1066,1333, 1600

QRx4 8GB 16GB 32GB 800 1066

QRx8 4GB 8GB 16GB 800 1066

Note: For detailed information on memory support and updates, please refer to the SMC

Recommended Memory List posted on our website at http://www.supermicro.com/support/

resources/mem.cfm.

4 356

BIOS Beep Codes

Beep Code/LED Message Description

1 beep Refresh Circuits have been reset.

(Ready to power up)

5 short beeps + 1 long

beep

Memory Error

5 long beeps + 2 short

beeps

Display memory

read/write status

Video adapter missing or with

faulty memory

1 continuous beep System OH System overheat

No memory detected

Screw #B

Screw #D

Screw #C

Screw #A

SNK-P0047PS

for CPU2

SNK-P0047PW

for CPU1

ÌMNL-1414-QRG^Î