Quick reference (1.0)

ManualsBrandsSupermicro ManualsServerSS1027B-URF

http://www.supermicro.com MNL-1394-QRG

Board Layout

SuperServer 1027B-URF Quick Reference Guide

Rear View

Power Button

Reset Button

UID Button (Unit Identifier Button)

Power LED

Device Activity LED

LAN1 LED & LAN2 LED

Overheat & Fan Fail LED

Hard Drive Signal

Hard Drive Fail

Description

No.

CPU Installation

Beep Codes

PCI-E 3.0 x8 Expansion Slot (FH, 13.5”L)

UIO Expansion Slot

Optional 2 LAN (RSC-R1UU-E8PR + AOC-PG-i2+) *

UID Button (Unit Identifier Button)

Dedicated LAN for IPMI

Redundant Power Supply Module

Description

No.

Front View & Interface



Heatsink Installation

1. Place heatsink on top of installed CPU

2. Line up the four screws to socket

3. Push down heatsink and screw down as shown

(cross pattern, in order: A, C, B, D)

4. NOTE: Only use 6-8 lb/f of torque; otherwise, hand-tighten

each screw, to avoid damaging the system

MEMORY

Caution

SAFETY INFORMATION

IMPORTANT: See installation instructions and safety warning

before connecting system to power supply.

http://www.supermicro.com/about/policies/safety_information.cfm

WARNING:

To reduce risk of electric shock/damage to equipment,

disconnect power from server by disconnecting all power

cords from electrical outlets.

If any CPU socket empty, install protective plastic CPU cap

CAUTION:

Always be sure all power supplies for this system have

the same power output. If mixed power supplies are

installed, the system will not operate.

Top View of DDR3 Slot

Release Tab

Note: Notch should align

with the receptive key

point on the slot.

Notch

Front View

Align CPU to socket;

install CPU straight down

For more information go to :

http://www.supermicro.com/support



NOTE:

Do not bend pin inside socket



Note: For detailed information on memory support and updates, please refer to the SMC Recommended Memory List

posted on our website at http://www.supermicro.com/support/resources/mem.cfm.

I-SATA1

I-SATA0

I-SATA4

I-SATA3

I-SATA2

I-SATA5

JSD1

T-SGPIO1

T-SGPIO2

JBT1

JF1

Battery

SAS0~3

SXB2: CPU2 PCI-E 3.0 X8

SXB1: CPU2/CPU1 PCI-E 3.0 X8 + x8

P1 DIMMC2

P1 DIMMC1

P1 DIMMB2

P1 DIMMB1

P2 DIMMF2

P2 DIMMF1

P2 DIMME2

P2 DIMMD2

P2 DIMME1

P2 DIMMD1

UIO

UID

P1 DIMMA1

P1 DIMMA2

Intel IOH

X9DBU-IF

CPU1

CPU2

[CPU2_Port3D]

[CPU2_Port3C]

[CPU2_Port1B]

[CPU2_Port1A]

[CPU1_Port3A]

[CPU1_Port3B]

Description

No.

P1-DIMMA1 (Blue)/P1-DIMMA2 slot

P1-DIMMB1 (Blue)/P1-DIMMB2 slot

P1-DIMMC1 (Blue)/P1-DIMMC2 slot

P1-DIMMD1 (Blue)/P1-DIMMD2 slot

P1-DIMME1 (Blue)/P1-DIMME2 slot

P1-DIMMF1 (Blue)/P1-DIMMF2 slot

CPU1 (Install CPU1 first)

CPU2

I-SATA 0/1 are SATA 3.0 ports

I-SATA 2~5 are SATA 2.0 ports

Serial-Link S-SATA/SAS 0~3

JBT1 = CMOS Reset

JDS1 = SATA DOM Power

SXB1 CPU1/CPU2 PCI-E 3.0 x8 + x8 slot

UIO SMC-Proprietary Universal I/O Slot

SXB2 CPU2 PCI-E 3.0 x8 Slot

SXB3 CPU1 PCI-E 3.0 x8 Slot

Note: Install CPU1 first

Intel E5-2600 Series Processor UDIMM Memory Support

Ranks per DIMM

& Data Width

Memory Capacity

Per DIMM

(See the Note below)

Speed (MT/s) and Voltage Validated by Slot per Channel (SPC)

and DIMM Per Channel (DPC)

SRx8 Non-ECC

2 Slots Per Channel

1DPC 2DPC

1.35V

1.5V

1.35V

1.5V

1GB 2GB 4GB

DRx8 Non-ECC

SRx16 Non-ECC

SRx8 ECC

DRx8 ECC

2GB 4GB 8GB

512MB 1GB 2GB

1GB 2GB 4GB

2GB 4GB 8GB

1066, 1333

1066

1066, 1333

1066

1066, 1333

1066

1066, 1333

1066

1066, 1333

1066

Installing RDIMM (ECC) Memory

Installing UDIMM (ECC/non-ECC) Memory

Intel E5-2600 Series Processor RDIMM Memory Support

Ranks

per

DIMM

& Data

Width

Memory Capacity

Per DIMM

(See the Note below)

Speed (MT/s) and Voltage Validated by Slot per Channel (SPC) and DIMM Per Channel (DPC)

SRx8

2 Slots Per Channel

1DPC 2DPC

1.35V

1.5V

1.35V

1.5V

1GB 2GB 4GB

DRx8

SRx4

DRx4

QRx4

2GB 4GB 8GB

4GB 8GB 16GB

8GB 16GB 32GB

1066, 1333, 1600

1066, 1333

1066, 1333, 1600

1066, 1333

1066, 1333, 1600

1066, 1333

1066, 1333, 1600

1066, 1333

1066, 1333, 1600

1066, 1333

1066, 1333, 1600

800

1066

800

QRx8

4GB

8GB

16GB

1066, 1333

800

1066 800 800

Processors and Memory Module Population for Optimal Performance

Number of

CPUs + DIMMs

CPU and Memory Population Configuration Table

(For memory to work properly, follow the instructions below)

1 CPU & 2 DIMMs

CPU1 & P1-DIMMA1/P1-DIMMB1

1 CPU & 4 DIMMs

1 CPU & 6 DIMMs

2 CPUs & 4 DIMMs

2 CPUs & 6 DIMMs

CPU1 & P1-DIMMA1/P1-DIMMB1, P1-DIMMA2/P1-DIMMB2

CPU1 & P1-DIMMA1/P1-DIMMB1, P1-DIMMA2/P1-DIMMB2, P1-DIMMC1/P1-DIMMC2

CPU1 + CPU2 & P1-DIMMA1/P1-DIMMB1, P2-DIMMD1/P2-DIMME1

CPU1 + CPU2 & P1-DIMMA1/P1-DIMMB1/P1-DIMMC1, P2-DIMMD1/P2-DIMME1/P2-DIMMF1

2 CPUs & 8 DIMMs

2 CPUs & 10 DIMMs

2 CPUs & 12 DIMMs

CPU1 + CPU2 & P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMA2, P2-DIMMD1/P2-DIMME1/P2-DIMMF1/P2-DIMMD2

CPU1 + CPU2 & P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMA2/P1-DIMMB2, P2-DIMMD1/P2-DIMME1/P2-DIMMF1

/P2-DIMMD2/P2-DIMME2

CPU1 + CPU2 & P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMA2/P1-DIMMB2/P1-DIMMC2, P2-DIMMD1/P2-DIMME1/

P2-DIMMF1/P2-DIMMD2/P2-DIMME2/P2-DIMMF2

Processors and their Corresponding Memory Modules

CPU#

Corresponding DIMM Modules

CPU 1

P1-DIMMA1

CPU 2 P2-DIMMD1

P1-DIMMA2

P2-DIMMD2

P1-DIMMB1

P2-DIMME1

P1-DIMMB2

P2-DIMME2

P1-DIMMC1

P2-DIMMF1

P1-DIMMC2

P2-DIMMF2

Populating LRDIMM (ECC) Memory

Intel E5-2600 Series Processor RDIMM Memory Support

Ranks

per

DIMM

& Data

Width

Memory Capacity

Per DIMM

(See the Note below)

Speed (MT/s) and Voltage Validated by Slot per Channel (SPC) and DIMM Per Channel (DPC)

QRx4 (DDP)

2 Slots Per Channel

1DPC 1 DPC and 2DPC

1.35V

1.5V

1.35V

1.5V

16GB 32GB

QRx8 (P) 2GB 16GB

1066, 1333

1066

1066, 1333

1066

1066, 1333

1 Slot Per Channel

BIOS Beep Codes

Beep Code/LED Message Description

1 beep Refresh Circuits have been reset.

(Ready to power up)

5 short beeps + 1 long

beep

Memory

5 long beeps + 2 short

beeps

Display memory

read/write status

Video adapter missing or with

faulty memory

1 continuous beep System System overheat

No memory detected

2 1

567

Screw #CScrew #B

Screw #A Screw #D

* Can be supported only with VLP memory installed

MNL-1394-QRG