Quick reference (2.0)

ManualsBrandsSupermicro ManualsServerSS1027B-MTF

http://www.supermicro.com

MNL-1405-QRG

Board Layout

SuperServer 1027B-MTF Quick Reference Guide

Rear View

Power Button

Reset Button

UID Button

Power LED

Device Activity LED

LAN1 LED & LAN2 LED

Overheat & Fan Fail LED

Hard Drive Signal

Hard Drive Fail

Description

No.

CPU Installation

Beep Codes

Description

No.

Front View & Interface



Heatsink Installation

1. Place heatsink on top of installed CPU

2. Line up the four screws to socket

3. Push down heatsink and screw down as shown

(cross pattern, in order: A, C, B, D)

4. NOTE: Only use 6-8 lb/f of torque; otherwise, hand-tighten

each screw, to avoid damaging the system

MEMORY

Caution

SAFETY INFORMATION

IMPORTANT: See installation instructions and safety warning

before connecting system to power supply.

http://www.supermicro.com/about/policies/safety_information.cfm

WARNING:

To reduce risk of electric shock/damage to equipment,

disconnect power from server by disconnecting all power

cords from electrical outlets.

If any CPU socket empty, install protective plastic CPU cap

CAUTION:

Always be sure all power supplies for this system have

the same power output. If mixed power supplies are

installed, the system will not operate.

Align CPU to socket;

install CPU straight down

For more information go to :

http://www.supermicro.com/support



NOTE:

Do not bend pin inside socket



2 1

Note:

Install CPU1 first

Description

No.

P1-DIMM1A slot

P1-DIMM1B slot

P1-DIMM1C slot

P1-DIMM1D slot

P2-DIMM1E slot

P2-DIMM1F slot

CPU1 (Install CPU1 first)

CPU2

I-SATA 0/1 are SATA 3.0 ports)

I-SATA 2~5 are SATA 2.0 ports

JBT1 = CMOS Reset

JDS1 = SATA DOM Power

LED3

JBT1

JPI2C1

S-SATA/

SAS0

CPU1 SLOT2 PCI-E 3.0 X4(IN X8)

P2-DIMM1F

P2-DIMM1E

P2-DIMM1D

P1-DIMM1B

P1-DIMM1A

P1-DIMM1C

CPU2 SLOT3 PCI-E 3.0 X8

CPU2 SLOT5 PCI-E 3.0 X8

CPU2 SLOT4 PCI-E 3.0 X8

CPU1 SLOT6 PCI-E 3.0 X16

SLOT1 PCI 33MHZ

Battery

Intel PCH

X9DBL-iF

S-SATA/

SAS1

S-SATA/

SAS2

S-SATA/

SAS3

3 4

Slot1 PCI 33MHz

CPU1 Slot2 PCI-E 3.0 x4 (in x8)

CPU2 Slot3 PCI-E 3.0 x8

CPU2 Slot4 PCI-E 3.0 x8

CPU2 Slot5 PCI-E 3.0 x8

CPU1 Slot6 PCI-E 3.0 x16

10 11 12

CPU1

CPU2

Top View of DDR3 Slot

Release Tab

Note: Notch should align

with the receptive key

point on the slot.

Notch

Front View

Intel E5-2400 Series Processor UDIMM Memory Support

Ranks per DIMM & Data Width Memory Capacity Per DIMM

(See the Note below)

SRx8 Non-ECC

1 Slot Per Channel

1DPC

1.35V

1.5V

1GB 2GB 4GB

DRx8 Non-ECC

SRx16 Non-ECC

SRx8 ECC

DRx8 ECC

2GB 4GB 8GB

512MB 1GB 2GB

1GB 2GB 4GB

2GB 4GB 8GB

1066, 1333

Installing RDIMM (ECC) Memory

Population UDIMM ECC-Non ECC Memory Modules

Intel E5-2400 Series Processor RDIMM Memory Support

Ranks per DIMM & Data Width Memory Capacity Per DIMM

(See the Note below)

SRx8

1 Slot Per Channel

1DPC

1.35V

1.5V

1GB 2GB 4GB

DRx8

SRx4

DRx4

QRx4

2GB 4GB 8GB

4GB 8GB 16GB

8GB 16GB 32GB

1066, 1333

1066, 1333, 1600

1066, 1333

1066, 1333, 1600

1066, 1333

1066, 1333, 1600

1066, 1333

1066, 1333, 1600

800

QRx8

4GB

8GB

16GB

800

Processors and Memory Module Population for Optimal Performance

Number of

CPUs + DIMMs

CPU and Memory Population Configuration Table

(For memory to work properly, follow the instructions below)

1 CPU & 1 DIMMs

CPU1 & P1-DIMM1A

1 CPU & 2 DIMMs

1 CPU & 3 DIMMs

2 CPUs & 2 DIMMs

2 CPUs & 3 DIMMs

CPU1 & P1-DIMM1A, P1-DIMM1B

CPU1 & P1-DIMM1A, P1-DIMM1B, P1-DIMM1C

CPU1 + CPU2 & P1-DIMM1A, P2-DIMM1D

CPU1 + CPU2 & P1-DIMM1A, P2-DIMM1D/P1-DIMM1B

2 CPUs & 4 DIMMs

2 CPUs & 5 DIMMs

2 CPUs & 6 DIMMs

CPU1 + CPU2 & P1-DIMM1A, P2-DIMM1D, P1-DIMM1B, P2-DIMM1E

CPU1 + CPU2 & P1-DIMM1A, P2-DIMM1D, P1-DIMM1B, P2-DIMMD1E, P1-DIMM1C

CPU1 + CPU2 & P1-DIMM1A, P1-DIMM1D, P1-DIMM1B, P2-DIMM1E, P1-DIMM1C, P2-DIMM1F

Processors and their Corresponding Memory Modules

CPU#

Corresponding DIMM Modules

CPU 1

P1-DIMM1A

CPU 2 P2-DIMM1D

P1-DIMM1B

P2-DIMM1E

P1-DIMM1C

P2-DIMM1F

Installing LRDIMM (ECC) Memory

Intel E5-2400 Series Processor RDIMM Memory Support

Note: For detailed information on memory support and updates, please refer to the SMC Recommended Memory List

posted on our website at http://www.supermicro.com/support/resources/mem.cfm.

Ranks per DIMM & Data Width

Memory Capacity Per DIMM

(See the Note below)

QRx4 (DDP)

1 Slot Per Channel

1DPC

1.35V

1.5V

16GB 32GB

QRx8 (P) 8GB 16GB

1066

1066, 1333

1066

1066, 1333

BIOS Beep Codes

Beep Code/LED Message Description

1 beep Refresh Circuits have been reset.

(Ready to power up)

5 short beeps + 1 long

beep

Memory

5 long beeps + 2 short

beeps

Display memory

read/write status

Video adapter missing or with

faulty memory

1 continuous beep System System overheat

No memory detected

PCI Expansion Slot (w/riser card)

UID Button

Dedicated LAN for IPMI

Power Supply Module

HDD 1

HDD 0

HDD 3

HDD 2

HDD 5

HDD 4

HDD 6 HDD 7

Screw #B

Screw #D

Screw #A

SNK-P0037P for CPU2

SNK-P0041 for CPU1

Screw #A

Screw #D

Screw #C

Screw #B

MNL-1405-QRG

Screw #C

ÌMNL-1405-QRG_Î