Quick reference (1.0)

ManualsBrandsSupermicro ManualsServerSS1018D-73MTF

http://www.supermicro.com MNL-1460-QRG

Board Layout

SuperServer 1018D-73MTF Quick Reference Guide

CPU Installation

Beep Codes

Front View & Interface



Heatsink Installation

1. Place heatsink on top of installed CPU

2. Line up the four screws to socket

3. Push down heatsink and screw down as shown

(cross pattern, in order: A, C, B, D)

4. NOTE: Only use 6-8 lb/f of torque; otherwise, hand-tighten

each screw, to avoid damaging the system

MEMORY

Caution

Screw #B

Screw #D

Screw #C

Screw #A

Align CPU to socket;

install CPU straight down

NOTE:

Do not bend pin inside socket



SAFETY INFORMATION

IMPORTANT: See installation instructions and safety warning

before connecting system to power supply.

http://www.supermicro.com/about/policies/safety_information.cfm

WARNING:

To reduce risk of electric shock/damage to equipment,

disconnect power from server by disconnecting all power

cords from electrical outlets.

If any CPU socket empty, install protective plastic CPU cap

CAUTION:

Always be sure all power supplies for this system have

the same power output. If mixed power supplies are

installed, the system will not operate.

For more information go to :

http://www.supermicro.com/support



Description

No.

PCH Slot5 PCI-E 2.0 x4 (in x8)

CPU Slot6 PCI-E 2.0 x8 (in x16)

JTPM1 = Trusted Platform Module/Port 80 Connector

CPU

P1-DIMMA1 (BLUE)/P1-DIMMA2 slot

P1-DIMMB1 (BLUE)/P1-DIMMB2 slot

L-SAS 0-7: (L)-SAS Connector 0-7

(supported by the LSI 2308 SAS controller)

I-SATA 2~5: SATA 2.0 ports (3Gb/s)

I-SATA 0~1: SATA 3.0 ports (6Gb/s)

JBT1 = CMOS Reset

JSD1 = Disk On Module (DOM) Power

BIOS Beep Codes

Beep Code/LED Message Description

5 short beeps + 1 long beep

Memory

5 long beeps

Display memory read/

write status

Video adapter missing or with faulty memory

No memory detected

1 beep

Refresh

Circuits have been reset. (Ready to power up)

1 beep per device

OH LED On

System overheat

System

Refresh

1 beep for each USB device

Rear View

Power Button

Reset Button

UID Button

Power LED

Device Activity LED

LAN1 LED & LAN2 LED

Information LED

Hard Drive Signal

Hard Drive Fail

Description

No.

2 13

HDD 1

HDD 0

HDD 3

HDD 2

HDD 5

HDD 4

HDD 6 HDD 7

4567

IPMI CODE

SAS CODE

BIOS

LICENSE

BAR CODE

MAC CODE

FAN2

FAN3

FAN1

FAN4

FANA

JBR1

JPL2

JPS1

JPUSB1

JPL1

JWD1

JLED1

JPB1

JPG1

JPME1

JPME2

J19

J18

LE3

LE5

LE4

JPW1

JPW2

J21

JI2C1

JI2C2

L-SAS0

L-SAS1

L-SAS2

L-SAS3

L-SAS4

L-SAS5

L-SAS6

JPI2C1

JTPM1

6-SGPIO1

T-SGPIO1

T-SGPIO2

JSD1

SPKR1

JBT1

SW1

CPU SLOT6 PCI-E 3.0 X8 (IN X 16)

USB1 (3.0)

USB0 (3.0)

COM2

USB8/9

_LAN

IPMI

VGA

COM1

LAN2

JL1

LAN1

DIMMB2

DIMMA

USB4/5

CPU

JF1

USB2/3

I-SATA3

I-SATA4

I-SATA2

I-SATA1

I-SATA0

I-SATA5

PCH SLOT5 PCI-E 2.0 X4 (IN X 8)

DIMMB1

DIMMA1

JSTBY1

L-SAS7

6-SGPIO2

Battery

PCH

SAS

CTRL

LAN

CTRL

LAN

CTRL

BMC

X10SL7-F

CPU1

BIOS

Front Panel CTRL

JOH1

LEDS2

LE6

5 6

ÌMNL-1460-QRGaÎ

Description

No.

PCI-E Expansion Slot (w/riser card)

UID Button

VGA Port

GbE LAN2 Port

GbE LAN1 Port

USB 4/5/6/7 Ports

COM1 Port

Dedicated LAN for IPMI

Single Power Supply Module

DDR3 Unbuffered Non-ECC (UDIMM) Memory

DIMM Slots per

Channel

DIMMs Populated

per Channel

DIMM Type POR Speeds Ranks per DIMM (any

combination)

2 1 Unb. ECC

DDR3

1066, 1333, 1600 Single Rank, Dual Rank

2 2 Unb.ECC

DDR3

1066, 1333, 1600 Single Rank, Dual Rank

DIMMA1

DIMMA2

(Blue Slot)

DIMMB2

(Blue Slot)

DIMMB1

Polpulating these DIMM modules with a pair of memory modulesof the same type and same size wil result

in interleaved memory, which will improve memory performance

Notches

Release Tabs

Press Both Notches

Straight Down into the

Memory Slot