Quick reference (1.0)

ManualsBrandsSupermicro ManualsServerSS1017C-TF

http://www.supermicro.com MNL-1288-QRG

Board Layout

SuperServer 1017C-TF Quick Reference Guide

Rear View

CPU Installation

Beep Codes

Front View & Interface

Heatsink Installation

1. Place heatsink on top of installed CPU

2. Line up the four screws to socket

3. Push down heatsink and screw down as shown

(cross pattern, in order: A, C, B, D)

4. NOTE: Only use 6-8 lb/f of torque; otherwise, hand-tighten

each screw, to avoid damaging the system

MEMORY

Caution

Screw #B

SAFETY INFORMATION

IMPORTANT: See installation instructions and safety warning

before connecting system to power supply.

http://www.supermicro.com/about/policies/safety_information.cfm

WARNING:

To reduce risk of electric shock/damage to equipment,

disconnect power from server by disconnecting all power

cords from electrical outlets.

If any CPU socket empty, install protective plastic CPU cap

CAUTION:

Always be sure all power supplies for this system have

the same power output. If mixed power supplies are

installed, the system will not operate.

For more information go to :

http://www.supermicro.com/support



J31

JTPM

J29

JL1

JI2C2

JI2C1

T-SGPIO1

JWF1

JPW2

JWOL

JSPK

JPI2C

JPW1

SPKR1

JBT1

LE2

JWD

JLED1

JPL2

JPG1

JPB

JPL1

JPUSB1

FAN1

FANA

FAN3

FAN2

DDR3 1066/1333 UDIMM required

USB4/5

USB 12/13

COM2

USB11

DIMM2B

DIMM2A

USB2/3

Slot6 PCI-E 2.0 x8

JF1

I-SATA2

Slot4 PCI-E 2.0 x4 on x8

KB/MOUSE

DIMM1B

DIMM1A

CPU

Slot7 PCI-E 2.0 x8

BIOS

Battery

PHY

BMC

CTRL

82574L

S I/O

T-SGPIO2

FP CTRL

Memory Chip

X9SCM-F

Fan4

PHY

82579

PHY

(For X9SCM only)

Socket H2

LGA 1155

CPU

I-SATA4

I-SATA5

I-SATA3

I-SATA1

I-SATA0

Slot5 PCI-E 2.0 x4 on x8

USB/0/1

LAN1

LAN2

LE7

JPME1

JPME2

Description

No.

Slot4 PCI-E 2.0 x4 on x8 slot

Slot6 PCI-E 2.0 x8

Slot7 PCI-E 2.0 x8

CPU1

DIMM1A / DIMM2A (Blue Slot)

DIMM1B / DIMM2B (Blue Slot)

SATA 3.0 (0/1 Ports)

JWF1 = SATA DOM Power Connector

SATA 2.0 (2/3/4/5 Ports)

JBT1 = CMOS Clear

BIOS Error Beep Codes

Beep Code/LED Error Message Description

1 beep Refresh Circuits have been reset.

(Ready to power up)

5 short beeps + 1 long

beep

Memory error No memory detected in the

system

8 beeps Display memory

read/write error

htiw ro gnissim retpada oediV

faulty memory

OH LED On System OH System Overheat

NOTE:

Do not bend pin inside socket



North Center Edge

South

Center Edge

SATA Drive Installation

The Serial ATA drives are mounted in drive carriers

to simplify their installation and removal from

the chassis.These carriers also help

promote proper air Serial ATA drive bays.

For this reason, even empty carriers

without Serial ATA drives installed

must remain in the chassis.

Installing a SATA Drive

Remove the dummy drive, which comes pre-installed in the drive carrier, by removing the

screws securing the dummy drive to the carrier. Note that these screws cannot be reused

on the actual 2.5” hard drive.

Use caution when working around the SATA backplane. Do not touch the backplane with any metal objects and make

sure no ribbon cables touch the backplane or obstruct the holes, which aid in proper airflow.

Important: Regardless of how many SATA drives are installed, both drive carriers must remain in the drive bays to

maintain proper airflow.

Enterprise level hard disk drives are recommended for use in Supermicro chassis and servers. For information on

recommended HDDs, visit the Supermicro Web site at http://www.supermicro.com/products/nfo/storage.cfm

Drive Installation

Screw #C

Screw #D

Screw #A

Recommended Population (Balanced)

DIMM2A Slot DIMM2B Slot DIMM1A Slot DIMM1B Slot Total System Memory

2GB DIMM 2GB DIMM 4GB

2GB DIMM 2GB DIMM 2GB DIMM 2GB DIMM 8GB

4GB DIMM 4GB DIMM 8GB

4GB DIMM 4GB DIMM 4GB DIMM 4GB DIMM 16GB

8GB DIMM 8GB DIMM 16GB

8GB DIMM 8GB DIMM 8GB DIMM 8GB DIMM 32GB

DIMM1A

DIMM2A (Blue Slot)

DIMM2B (Blue Slot)

DIMM1B

Power LED

Device Activity LED

LAN1 LED & LAN2 LED

Information LED

Power Button

Description

No.

UID

1234

567

Reset Button

UID

Hard Drive Signal

Hard Drive Fail

Description

No.

Description

No.

PCI-E Expansion Slot (w/riser card)

GbE LAN1 & LAN2 Port

VGA Port

COM1 Port

USB 0/1 Ports

PS2 keyboard (purple) & Mouse (green) Ports

Single Power Supply Module

Insert a drive into the carrier with the PCB side facing down and the connector end toward

the rear of the carrier.

Align the drive in the carrier so that the screw holes of both line up. Note that there are holes

in the carrier marked “SAS” or “SATA” to aid in correct installation.

Secure the drive to the carrier with four screws as illustrated below.4.

Insert the drive carrier into its bay, keeping the carrier oriented so that the hard drives is on

the top of the carrier and the release button is on the right side. when the carrier reaches

the rear of the bay, the release handle with retract.

Push the handle in unit it clicks into its locked position.6.

ÌMNL-1288-QRG<Î

UID