Manualshelf

Quick reference (1.0)

ManualsBrandsSupermicro ManualsMotherboardPDSMA+
1
S
UPERMICR
R
ContaCt InformatIon
MNL-0907 -QRG
• www.supermicro.com(Email:support@supermicro.com)
• Manuals:http://www.supermicro.com/support/manuals
• Drivers&Utilities:ftp://ftp.supermicro.com
• Safety:http://www.supermicro.com/about/policies/safety_information.cfm
© 2012 Supermicro Computer Inc. All rights reserved. Reproduction of this document whether in part or in whole is strictly prohibited without Supermicro's written
consent. All Trademarks are property of their respective entities. All information provided is deemed accurate at the time of printing; however, it is not guaranteed.
PaCkage Contents
(Appliestoindividual-packonly)
PDsma+ / PDsma-e+
motherboarD QuICk referenCe guIDe
• One(1)SupermicroMotherboard
• One(1)IDECable
• Four(4)SATACables
• One(1)FloppyDriveRibbonCable
• One(1)I/OShield
• OneQuickReferenceGuide
PCI 32-bit 33 MHz
S
+/PDSMA-E+AMSDP REPU
®
CPU
LGA 775
KB/MS
COM1
JLAN1
North Bridge
JPL1
JL1
JWOR
24-Pin ATX PWR
ICH7R
1FJ
South Bridge
J31
J28
8-pin PWR
Battery
J9
LRTC PF
USB 1/2
J15
VGA
JG1
JLAN2
LAN1
CTRL
S I/O
Printer
JPL2
Floppy
Slot1
DIMM 2B
PCI-X 64-bit 133 MHz
BIOS
PXH-V
JPW1
J27
Primary IDE
4J
J 3
LE1
JBT1
USB3/4
USB5/6
JP3
JPF
JWD
WOL
Fan3
DIMM 1B
DIMM 2A
DIMM 1A
DIMM 1
DIMM 2
DIMM 3
DIMM 4
JPW2
VGA
CTRL
Slot6
LE3
LE4
*Compact Flash only
COM2
Slot2
Slot3
Slot4
Slot5
PCI 32-bit 33 MHz
JI2C1
JI2C2
JPG1
LAN2
CTRL
IPMI 2.0
I-SATA0
I-SATA1
I-SATA2
I-SATA3
J46
J45
Fan1
Fan4
Fan6
Fan2
Fan5
PCI 32-bit 33 MHz
PCI 32-bit 33 MHz
PCI 32-bit 33 MHz
JWF1
SPKR
Slot7
PCI-Exp. x8
Intel 3000
JPR1
PW3
PW4
(CPU Fan)
Intel 3010
(PDSMA+)
(PDSMA-E+)
Jumpers, Connectors and LED Indicators
Back Panel I/O Connectors
Memory Support
Motherboard Layout and Features
CPU Installation
Note: Graphics shown in this quick reference guide are for illustration only. Your components may or may not look exactly the same as drawings shown in this guide.
Note: Refer to Chapter 1 of the User Manual for detailed information on jumpers, connectors,
and LED indicators.
Heatsink Installation
Front Panel Control (JF1)
Jumpers
Connectors
LED Indicators
This motherboard supports up to 8GB of dual channel, ECC/Non-ECC unbuffered
DDR2 667/533/400 MHz SDRAM in 4 memory slots.
Note: For memory optimization, use only DIMM modules that have been validated by Supermicro.
For the latest memory updates, please refer to our website at http://www.supermicro.com/products/
motherboard.
Memory Population Guidelines
When installing memory modules, the DIMM slots should be populated in the following
order: DIMM1A, DIMM1B and DIMM2A, DIMM2B.
Possible System Memory Allocation & Availability
System Device Size Physical Memory
Remaining (-Available)
(4 GB Total System Memory)
Firmware Hub ash memory
(System BIOS)
1 MB 3.99
Local APIC 4 KB 3.99
Area Reserved for the chipset 2 MB 3.99
I/O APIC (4 Kbytes) 4 KB 3.99
PCI Enumeration Area 1 256 MB 3.76
PCI Express (256 MB) 256 MB 3.51
PCI Enumeration Area 2 (if
needed) -Aligned on 256-MB
boundary-
512 MB 3.01
VGA Memory 16 MB 2.85
TSEG 1 MB 2.84
Memory available to OS and
other applications
2.84
DIMM1B
DIMM2B
Towards the edge of the motherboard
Towards the CPU
DIMM Memory Installation
Item # Jumper Description Default
8
JI
2
C1, JI
2
C2
SMbus to PCI Slot Open/Open (Disabled)
9 JPL1, JPL2 Giga-bit LAN1/LAN2 Enable Pins 1-2 (Enabled)
34 JPG1 VGA Enable Pins 1-2 (Enabled)
36 JBT1 CMOS Clear See Section 2-7 in Manual
39 JPF Power Force-On Open (Disabled)
40 JWD Watch Dog Enable Pins 1-2 (Reset)
42 JP3 Compact Flash Master/Slave Closed (Master)
Item # LED Description
20 LE1 Onboard PWR warning LED Indicator
37, 38 LE4, LE3 BIOS POST Code Indicator
Item # Connector Description
1 KB/MS PS/2 Keyboard and Mouse
2 USB 1/2 Back Panel Universal Seral Bus Ports 1 & 2
3, 10 COM1, COM2 COM Port1, COM 2 Header
4 VGA VGA Connector
5, 6 JLAN1, JLAN2 Ethernet RJ45 (Gigabit LAN) Port1/Port2 Connectors
7, 22, 35 Fan5, Fan4, Fan6 System Fan Headers (Fan 4, 5); CPU (Fan6)
11 Floppy (J27) Floppy Disk Connector
12 Printer Parallel Port Header
13 J9 Speaker Connector (Pins 3-4: Internal Buzzer)
14 WOL Wake On LAN Header
15 SPKR Internal Buzzer
16, 17 USB 5/6, USB 3/4 Front Panel Accessible USB Headers
18 JWOR Wake On Ring Header
19 JL1 Chassis Intrusion Header
21 I-SATA 0~3 Intel SATA Headers
23 Primary IDE (J3) IDE Master (See notes on page 1-4 in User Manual)
24 J4 Compact Flash (See notes on page 1-4 in User Manual)
25, 27, 28 Fan3, Fan2, Fan1 System Fan Headers
26 FP CTRL (JF1) Front Panel Control header
29 24-Pin ATX PWR (JPW1) ATX 24-Pin Power Connector
30 8-Pin ATX PWR (JPW2) 12V 8-Pin Power Connector (required)
31 JPR1 Alarm Reset
32 PW3 Power Fault Header (See Chapter 2 in User Manual)
33 PW4 Power System Management Bus (I
2
C)
41 IPMI IPMI 2.0 Socket
43 JWF1 Compact Flash PWR Connector
A
B
C
D
E
F
G
H
DIMM1A
DIMM2A
Lock
1. Open
socket
cover
2. Insert CPU (Align
Notches)
3. Close and
secure lever.
1. Apply
thermal
grease
2. Set heatsink
on CPU
3. Twist to lock
fasteners
1245678 39
10
11
12
13
14
15
16
17
18
19
20
21
22
23
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
24 25 26 27 28
A. Keyboard
B. PS/2 Mouse
C. USB Port 1
D. USB Port 2
E. COM Port 1
F. VGA Port
G. GLAN 1
H. GLAN 2
Power Button
OH/Fan Fail LED
1
NIC1 LED
Reset Button
2
HDD LED
Power LED
Reset
PWR
Vcc
Vcc
Vcc
Vcc
Ground
Ground
1920
Vcc
X
Ground
NMI
X
Vcc
X
NIC2 LED

Summary of content (1 pages)