User`s manual

Chapter 2: Installation
2-25
JPW3
JPW2
JBT1
JPI2C
COM1
I-SATA0
JPS1
JWD
JPL2
JPL1
JF1
SP1
1
JWOL
LE1
D20
JBAT1
JP3
JL1
JOH1
JPB
JP5
J16
JD1
CPU1 FAN
Slot3 PCI-E 1.0 x4 (in x8 Slot)
7HG
5ADG
7TN100C
W8379
W8352
Slot6 PCI-E 2.0 x8 (in x16 Slot)
JI2C2
SAS6
SAS5
SAS4
SAS3
SAS2
SAS1
Slot4 PCI-E 2.0 x4 (in x8 Slot)
BMC CTRL
WPCM450R
LC4128ZE-
ICH10R
(South Bridge)
5500
(IOH-24D)
P1-DIMM3A
P1-DIMM1A
P2-DIMM3A
P1-DIMM2A
P2-DIMM2A
P2-DIMM1A
KB/Mouse
USB0/1
VGA
LAN1
UID
LE2
Slot2 PCI 33MHz
Slot1 PCI 33MHz
COM2
IPMB
USB4/5
USB6
T-SGPIO2
USB2/3
I-SATA5
T-SGPIO1
I-SATA3
I-SATA2
I-SATA4
3-SGPIO2
3-SGPIO1
LSI SAS2 2008
SAS0
FAN5
FAN4
FAN6
FAN1/
CPU2
LAN2
IPMI LAN
LAN
CTRL
SAS7
JI2C1
LAN
CTRL
PHY
Chip
CPU1
Intel
Intel
JPW1
CPU2FAN
FAN2/
BIOS
Slot5 PCI-E 2.0 x4 (in x8 Slot)
X8DTL-6F Series
Flash ROM
BMC
Battery
Buzzer
1
FAN3
JPG1
JIBTN1
I-SATA1
LED1
DS7
DS6
JWOR
JPRST1
Rev. 2.01
A
B
A. T-SGPIO-1
B. T-SGPIO-2
C. 3-SGPIO-1 (X8DTL-6/-6L)
D. 3-SGPIO-2 (X8DTL-6/-6L)
E. RAIDKey (X8DTL-6/-6F/-6L)
C
T-SGPIO 1/2 & 3-SGPIO 1/2
Headers
Two SGPIO (Serial-Link General
Purpose Input/Output) headers (T-
SGPIO-1/T-SGPIO-2) are located the
motherboard. Two additional GPIO
connections (3-GPIO 1/2) are also
located on the X8DTL-6/-6L models.
These headers support serial link
interfaces for the onboard SATA and
SAS connectors. See the table on the
right for pin defi nitions. Refer to the
board layout below for the location.
Note: NC= No Connections
T-SGPIO
Pin Defi nitions
Pin# Defi nition Pin Defi nition
1NC 2 NC
3 Ground 4 Data
5 Load 6 Ground
7NC 8 NC
D
E
RAIDKey Header (Optional for
X8DTL-6/6F/6L Only)
A RAID Key header (JIBTN1) supports
AOC-IMRRAKey-2008-LSI, which will
allow the user to enable the onboard
SAS2 Controller for RAID 5 support.
RAIDKey Header
Pin Defi nitions
Pin# Defi nition
1 PWR
2 Ground