User`s manual

2-34
X7DA8+/X7DAE+ User's Manual
LAN1/2
®
S
UPER X7DA8+
Fan1
8-pin PWR
FP ControlSPK
PW LED
JOH1
Fan3
IDE1
Floppy
320 SCSI Channel A
Fan4
SATA3
SATA5
USB4/5
SMB
PCI-X 100 MHz ZCR (Green Slot)
PCI-X 133 MHz
JWD
Battery
GLAN
CTLR
JPG1
PCI-Exp x4
North Bridge
COM1
Fan6
Fan5
ATX PWR
4-Pin
PWR
J3P
24-Pin
SCSI CTRL
PXH
CPU1
CPU2
South Bridge
Fan7
JAR
J17
PSF
Fan2
Compact Flash
LE1
Fan8
JCF1 JWF1
JPA2
JPA3
JPA1
320 SCSI Channel B
SATA2
SATA4
SATA1
SATA0
JL1
PCI-X 133 MHz
JPL2
PCI-33MHz
FP Audio
PCI-Exp x16
SIM LP IPMI
DIMM 1A (Bank 1)
DIMM 1B (Bank 1)
DIMM 2A (Bank 2)
DIMM 2B (Bank 2)
DIMM 3A (Bank 3)
DIMM 3B (Bank 3)
DIMM 4A (Bank 4)
DIMM 4B (Bank 4)
JWOL
JWOR
KB/
Mouse
USB 0/
1/2/3
JI
2
C2
JI
2
C3
JI
2
C4
5000X
BIOS
DA1
DA2
CPU
Fan 1
CD1
JPL1
JI
2
C1
CPU Fan2
HD
Audio
SGPIO1
SGPIO2
Parrallel Port
Audio
CTRL
S I/O
J8
Clear
CMOS
ESB
Cha.
Intru.
IDE Drive Connectors
Pin Defi nitions
Pin# Defi nition Pin # Defi nition
1 Reset IDE 2 Ground
3 Host Data 7 4 Host Data 8
5 Host Data 6 6 Host Data 9
7 Host Data 5 8 Host Data 10
9 Host Data 4 10 Host Data 11
11 Host Data 3 12 Host Data 12
13 Host Data 2 14 Host Data 13
15 Host Data 1 16 Host Data 14
17 Host Data 0 18 Host Data 15
19 Ground 20 Key
21 DRQ3 22 Ground
23 I/O Write 24 Ground
25 I/O Read 26 Ground
27 IOCHRDY 28 BALE
29 DACK3 30 Ground
31 IRQ14 32 IOCS16
33 Addr1 34 Ground
35 Addr0 36 Addr2
37 Chip Select 0 38 Chip Select 1
39 Activity 40 Ground
A
B
A. IDE#1
B. IDE#2 (Compact Flash)
IDE Connectors
There are two IDE Connectors (JIDE1:
Blue, JIDE2: White) on the mother-
board. The blue IDE connector (JIDE1)
is designated the Primary IDE Drive.
The white IDE connector (JIDE2) is
designated the Secondary IDE Drive,
reserved for Compact Flash Card use
only. (See the note below.) See the
table on the right for pin defi nitions.
Note: JIDE2 (the white slot) is reserved
for Compact Flash Card only. Do not
use it for other devices. If JIDE2 is
populated with a Compact Flash Card,
JIDE1 (the blue slot) will be available for
one device only. For the Compact Flash
Card to work properly, you will need to
connect a power cable to JWF1 fi rst.