Installation Instructions

ManualsBrandsSuperFast ManualsFlooring & RugsHurricane Wood 5 x 48 Chestnut Oak Rigid Core Hardwood Flooring (22.98 sq.ft/ctn)

INSTALLATION GUIDELINES

SuperFast® Hurricane Naturals Rigid Core Wood Flooring

Thank you for choosing our flooring. When properly installed and cared for, your new flooring will be

easy to maintain and will keep its great look for years.

Please read all the instructions before you begin the installation. Improper installation will void warranty.

I. GENERAL PREPARATIONS

IMPORTANT NOTICE

All wood-based products, even those specifically designed to have increased resistance to moisture,

are hygroscopic (they will react to the moisture in the environment) and as a result will expand or

contract accordingly. All sources of under floor moisture must be rectified prior to the installation of

the floor. Any construction dampness must be completely dry. Although this product has been

designed with bathroom installation in mind it is not waterproof and excessive wetting is to be

avoided and water spillages dried promptly.

TOOLS REQUIRED: Spacers, rubber mallet, ruler, pencil, tape measure, utility knife.

 Prior to installation, inspect material in daylight for visible faults/damage, including defects or

discrepancies in color or shine; check the edges of the flooring for straightness and any damage.

No claims on surface defects will be accepted after installation.

 It is preferable to lay boards perpendicular to the window, following the direction of the main source

of light. For the best result, make sure to always work from 3 to 4 cartons at a time, mixing the

planks during the installation.

 Check if subfloor/site conditions comply with the specifications described in these instructions. If

you are not satisfied, do not install, and contact your supplier.

 Flooring products can be damaged by rough handling before installation. Exercise care when

handling and transporting these products. Store, transport and handle the flooring planks in a

manner to prevent any damage. Store cartons flat, never on edge.

 Flooring products can be heavy and bulky. Always use proper lifting techniques when handling

these products. Whenever possible, make use of material-handling equipment such as dollies or

material carts. Never lift more than you can safely handle; get assistance.

 Calculate the room surface prior to installation and plan an extra 5-10% of flooring for cutting

waste.

 The environment where the flooring is to be installed is critically important with regard to successful

installation and continued performance of the flooring products. This product is intended to be

installed in interior locations only. These interior locations must meet climatic and structural

requirements as well.

 In most cases, this product does not need to be acclimated. However, if the boxes of flooring were

exposed over 2 hours to extreme temperatures under 50°F / 10°C or over 104°F / 40°C within the

12 hours before the installation, acclimation is required. In this case, keep the boards in room

temperature for at least 12 hours in unopened package before you start the installation. The room

temperature must be maintained consistent between 70-80°F / 20-25°C at 30-65% relative

humidity before and during the installation.

Summary of content (6 pages)

PAGE 1
INSTALLATION GUIDELINES SuperFast® Hurricane Naturals Rigid Core Wood Flooring Thank you for choosing our flooring. When properly installed and cared for, your new flooring will be easy to maintain and will keep its great look for years. Please read all the instructions before you begin the installation. Improper installation will void warranty. I.
PAGE 2
   II.         Flooring should only be installed in temperature-controlled environments. It is necessary to maintain a constant temperature of 70-80°F / 20-25°C at 30-65% relative humidity before and during the installation. Portable heaters are not recommended as they may not heat the room and subfloor sufficiently. Kerosene heaters should never be used. After installation, make sure that the flooring is not be exposed to temperatures less than 50°F / 10°C or greater than 104°F / 40°C.
PAGE 3
DO NOT INSTALL OVER     Any type of carpet. Existing cushion-backed vinyl flooring. Floating floor of any type, loose lay, and perimeter fastened sheet vinyl. Hardwood flooring / wood subfloors that lay directly on concrete or over dimensional lumber or plywood used over concrete. IMPORTANT NOTICE In-floor Radiant Heat: Flooring can be installed over 1/2” / 12 mm embedded radiant heat using the floating method. Maximum operating temperature should never exceed 81°F / 27°C.
PAGE 4
   Decide the installation direction. It is recommended to install the boards perpendicular to the window following the direction of the main source of light. Measure the area to be installed: The board width of the last row shall not be less than 2” / 50 mm. If so, adjust the width of the first row to be installed. In narrow hallways, it is recommended to install the floor parallel to the length of the hall.
PAGE 5
IMPORTANT: If you notice both planks aren’t at the same height or are not well locked together, please follow the disassembling instructions at the bottom of the page, disassemble and check if any debris stuck inside the lock is obstructing. Failure to properly line up the end joint and attempting to force it in while out of alignment could result in permanent damage to the end joint. 3.
PAGE 6
       IV. Sweep or vacuum daily using soft bristle attachments. Clean up spills and excessive liquids immediately. Damp mop as needed and use cleaners recommended for wood flooring. Use proper floor protection devices such as felt protectors under furniture. Place a walk-off mat at outside entrances to reduce the amount of dirt brought into your home. Do not use mats with a latex or rubber backing since these backings can cause permanent discoloration.