METAL DETECTOR S3000
METAL DETECTOR OWNER’S MANUAL The metal detector is a detector designed for beginners,it is easy to use.With the latest design,the unit has good sensitivity and the ability to discrimination,the result of the detection will display on the LCD.Using the fully digital positioning circuit,improve the accuracy of positioning.In the field with electromagnetic interference,the fully digital positioning circuit has good anti-interference ability. Read this manual carefully before using.
To different types of metals, the detector will sound a different tone or give a different indication,and it will also eliminate the specific metal,we refer to this as “discrimination”.Discrimination is an important feature of metal detectors. Iron Iron is a common metal.It’s usually not the detection target,undesirable iron objects contains such as iron nail,bolts,old cans,caps and so on.But some valuable relics may also be made of iron,such as old armaments,old armature and so on.
Target metals discrimination: 3 kinds Sound frequency: Three kinds of sound indicating different metals Battery indication: Low battery indicate Turn off prompt: Sound a prompt tone every ten minutes Search coil: 210x70mm open waterproof search coil Earphone jack: 1/8 inch earphone jack(earphone not supplied) Power supply: 6 AA batteries (batteries not supplied) ASSEMBLY 1. 2.
Fig.2 3. Fig.3 Wind the cable around the aluminum tube, keep the elastic moderate,so that the cable won’t sway. BATTERY Please use 6 alkaline AA batteries. 1. Press the “key” on the battery cover in the direction of the arrow,pull out the battery cover.(Fig.4) 2. Fig.4 Insert the 6 AA batteries to the case as indicated by the polarity symbols marked inside the case. Fig.5 3. And then push the battery cover to the batter cavity.
result also can be shown on the LCD. (See Fig.6) Fig.6 Target ID pattern:It’s located above the LCD screen.It indicates the wanted target metals.When detecting a metal target,the target ID cursor will appear below the such metal patterns or the words. Target ID cursor:it’s in the shape of .It consists of 3 segments.When the target ID cursor is lighted,which indicates the probable metal type of the detected target.
Fig.7 Power button:press the button, the power is on,and press it once more,the power is off. SENS Button:choose the 3 levels with the SENS botton.Boot setting is the middle level(the second level).The highest sensitivity is the third level,when there is interference,you can set the sensitivity lower properly.In the PINPOINT mode,the SENS button is useless.
Fig.8 3. Turn on Press the POWER button,and the detector will sound two moo tones, all the LCD patterns are lighted at minute,the detector is in the ALL METAL mode by default,and the sensitivity is in the second grade.(See Fig.9) Fig.9 4. Test Sweep the three metal samples 5 to 8cm above the search coil. a) The detector sounds three different tones in turn. b) The depth cursor points to the second grade. c) The Target ID cursor points to the three materials.
Fig.10 5. PINPOINT mode test a) Press and hold down the “PINPOINT” button,the PINPOINT cursor is lighted,and the depth cursor points to the third grade.the detector will sound a low single-frequency mediant. (See Fig.11) Fig.11 b) Let the 25￠ silver coin approach the search coil slowly,when it is in the position of about 6”,the strength cursor begins to appear and turns stronger,the sound turns louder.
Fig.12 c) Maintain the position of the silver coin,release the PINPOINT button.Press the PINPOINT button again after several seconds,the lower cursor is extinguished,and the sound comes back to the initial state,the depth indication comes back to the full scale.
The users always expect to set the sensitivity more higher.However,in the higher sensitivity range,the detector will be sensitive to the electromagnetic interference that comes from the power lines or cables around,and it will do abnormal reaction to the mineralization soil or electrical conductivity soil.If you move the search coil in the detection area,and the detector will send an unstable false signal,please decrease the sensitivity.
6. PINPOINT When detecting in the motion mode,as you should persistently move the search coil,so although you find the region that burying metals,it’s not easy for you to determine the exact location,it gets the digging difficult.At this time,you should recur to the PINPOINT mode. a) press and hold down the PINPOINT button,the detector will sound a low single-frequency tone,and the sensitivity is in the highest state.
detection.If the depth indication varies,try to change the sweeping angle.There may be more than one target present. Remind you once again,when detecting in the wild,due to the impact of the ground condition,the discrimination indication and depth indication will be all deviation.The composition,size and oxidation of the metals will all affect the indication result.
Sound a successive “DI” “DI” tone Sound an irregular tone,or the target identification cursor chatters. The signal is instable,and the position of the target identification cursor change. Using PINPOINT,when the search coil approaches the ground,the unit will sound a tone. cover is upward. 3.Replace the batteries. 1.Make sure that there is no other metal detector operating around. 1.Don’t use it indoors,because there is many metals there. 2.
PART LIST NO ITEM QUANTITY NO 1 Battery cover 1 15 2 1 16 1 4 5 Battery compartment Battery compartment pressure plate Screw ST3x8F Cover 6 ITEM QUANTITY Rubber button 1 17 Panel 1 2 1 18 19 1 1 Rubber ring 1 20 7 Screw ST3x18F 2 21 8 Casing 1 22 9 LCD 1 23 10 11 PCB Pad 1 1 24 25 12 Screw ST2.
15
