MD6003 Instruction Manual The Metal Detector is a versatile and easy-to-use metal detector.It has higher sensitivity and has the ability to differentiate the ferrous metals and nonferrous metals. It is suitable for beginners. Please read the manual carefully before using the unit.
Assembly Assembly is cays and requires no special tools. 1. Align the plastic trapezium raised part on the handle. with the trapezium lower groove at the control box bottom (Figure. 1}. push the two parts tightly. Figure. 1 2. Align the threaded bolts at the handle bottom.with the knobs under the control box, lock it with the Figure.2 3.
Panel And Controller The Panel Controller (Figure. 7) View metal ~Low Batter Disc Tune (Power off) Volume ~~ Red Button Figure.7 ® Power off: Power on/off power supply. The same knob with the DISC. * TUNE: It is cooperated with. the Red Tuning Button, and adjust balance. Let the detector be in normal operation state. ® Red Button: It is cooperated with TUNE to adjust balance. * DISC: Adjust DISC will help the operator to differentiate the ferrous metals and nonferrous metals.
Figure. 10 Adjust the Volume potentiate, let you can hear the light hum one, don’t adjust it too loud. Once you adjust the “DISC” button, you should adjust the balance over again. In general, you should only press the Red Button to let the detector return to the balance state. During operating, if there is no metals around detector, while the meter pointer deviates from the “0” position, you should also adjust the balance over again, Test samples, discriminate ferrous metal and nonferrous metal.
7. Discriminate different metals approximately We take 5 € nickel coin and pull tab as an example to explain the approximate discrimination method. * Set the DISCRIMINATION to about “12:00” Adjust the balance to let the detector sound a hum tone, and the show is “0” DISC 0 MIN POWER OFF Figure.15 * Lethe iron nail, 5 € nickel coin and pull tab approach the search coil slowly, the sound tones light, and the meter pointer deflects to the left.
Figure. 16 Figure.17 ‘When finding metal objects, you should move the search coil on the ground according to figure 16, In order to determine the metal position exactly. The nearer the search coil from the object, the more strong the response is. Figure.18 6. Using the earphone To the change of sound, using the earphone is more sensitivity,and you will get better detection result.
PARTS LIST PARTS LIST Part | Description Ly Part | Description Qty 1 PCB i 20 | Left Arm Rest Support 1 2 | Screw M3X8 2 21 | Screw M3X12 3 3 | Adhesive Sticker 1 22 | Right Arm Rest Support 1 4 {LED 1 23 | Support Am Adjustment Knob View Meter 1 24 | Outer Stem 1 6 | Washer 3mm 2 25 | Washer 1 7 | Screw M3X8 2 26 | Inner Stem 1 § | Control Panel 1 27 | Lock Nut Interior 1 9 1 Support Arm{Right Side} Lock Nut Exterior 1 10 | Nut Look Nut Cover 1 11 | Screw M3X18 4 30 | Bush in; 1 12 | Screw M3X14 1 31 | Coi
PARTS LIST PARTS LIST Part | Description Qt Part | Description Qty 1 PCB 1 20 | Left Arm Rest Support 1 2 [Screw M3X8 2 21 | Screw M3X12 3 3 | Adhesive Sticker 1 22 | Right Arm Rest Support 1 4 {LED 1 23 | Support Arm Adjustment Knob View Meter 1 24 | Outer Stem 1 6 | Washer 3mm 2 25 | Washer 1 7 | Screw M3X8 2 26 | Inner Stem ! 8 | Control Panel 1 27 | Lock Nut Interior i 9 | Support Arkwright Side) i 28 | Lock Nut Exterior 1 10 | Nut Look Nut Cover 1 11 | Screw M3X18 4 30 | Bush in; 1 12 | Screw M3X14 1 3
