SP-503CDB INSTALLATION MANUAL CAR AUDIO SYSTEM Detachable Control Panel Remote Control AM/FM-RDS Radio and CD/MP3/WMA Player With Disc Slot/USB Port/Card Slot/AUX Input BT A2DP & AVRCP COMPATIBLE
Content Installation steps........................................................................... 2 General information about remote control...................................... 6 1. Removing insulating sheet......................................................... 6 2. Replacing the lithium cell........................................................... 6 3. Note about using the remote control........................................... 6 4. Warning about lithium cells of remote control................
INSTALLATION STEPS 1. Remove 2 screws for protecting deck; 1) Remove chassis from the Slide Bracket Housing as follows: KEY PLATE PLASTIC TRIM OUT KEY PLATE If you want to remove the chassis from the Slide Bracket Housing , first remove the Plastic trim from both sides, then insert 2 Key Plates into the left and the right side of the chassis as illustrated. 2) Remove 2 screws protecting the deck as illustrated on the right; 2.
3) Connecting all wires as bellows: REAR AUDIO OUT RCA JACK R (red) FRONT AUDIO OUT RCA JACK R (red) RADIO ANTENNA JACK REAR AUDIO OUT RCA JACK L (white) FUSE FUSE FRONT AUDIO OUT RCA JACK L (white) ISO CONNECTOR BLUE YELLOW BLACK RED FRONT Lch SPK. REAR WHITE GREY WHITE/BLACK GREY/BLACK GREEN VIOLET GREEN/BLACK VIOLET/BLACK Lch SPK. AUTO ANTENNA CONSTANT 12 VOLTS GROUND(B-) IGNITION SWITCH FRONT Rch SPK. REAR Rch SPK. NOTE: 1. Must use 4 ohms impedance of speakers. 2.
4) Attaching the control panel onto the chassis. A. Align and thrush the bulge of the control panel into the hollow of the chassis. Hollow Bulge B. Push the right end of the control panel to the chassis till a click sound is heard. Panel Connector * How to clean panel connector Frequent detachment will cause the panel connectors to deteriorate. To minimize deterioration, periodically wipe the panel connector with a clean/soft/dry cloth . 5) Test to make sure that it works properly. 3.
Installation diagram DASH BOARD HEX NUT METAL MOUNTING STRAP SPRING WASHER PLAIN WASHER TAPPING SCREW CONSOLE SLIDE BRACKET HOUSING HEX BOLT -5-
General information about the remote control 1. Removing insulating sheet The remote control comes with an insulating sheet attached to the underside of the remote control as illustrated on the right . The remote control is disabled and will not work until the insulating sheet is removed. 2. Replacing the lithium cell If the electric energy of the lithium cell is weak, replace it as illustrated on the right . 1.
Locations and Names of controls 1. Locations and Names of controls on main unit 2 16 7 4 15 19 5 14 22 6 24 3 17 25 8 21 9 10 11 12 13 20 1 Control Panel 23 18 Front side of chassis after removing control panel 1. REL button 14. |<< button 2. PWR or MODE button 15. >>| button 3. SEL button and VOL knob 16. PAIR or 4. BAND or ID3 or 17. EJECT button button button 5. TA or AF button 18. RESET button 6. APS button 19. IR sensor window 7. MUTE or PTY button 20. AUX IN jack 8.
2. Locations and Names of controls on remote control 11 1 12 13 2 14 3 15 4 5 16 6 17 18 7 8 TA AF PTY 19 9 20 10 21 NCA A -608 1. PWR button 11. VOL+ button 2. < button 12. MUTE or MODE button 3. button 4. VOL- button 13. SEL or ENTER button 14. > button 5. >|| or TOP or 1 button 15. 6. RDM or 4 button 16. RPT or 3 button button 7. -10 or 5 button 17. INT or 2 button 8. 7 or TA button 18. +10 or 6 button 9. DISP or * button 19. 9 or PTY button 10. 8 or AF button 20.
General Operation 1. PWR button To power main unit on , short press the PWR button on the control panel or on the remote control . To power main unit off, long press the PWR button on the control panel or short press the PWR button on the remote control . 2. VOL knob or VOL+ & VOL- button To increase or decrease volume level. 3. MUTE button To cancel or resume sound, long press the MUTE button on the control panel or long press the MUTE button on the remote control . 4.
Radio Operation 1. BAND button To switch between F1(FM1),F2(FM2),F3(FM3),A1(AM1) and A2(AM2). 2. |<< & >>| or < & > buttons In standby mode or after no manually searching operation for a while, briefly press one of them to automatically search down or up for an available station and listen to it. To manually search down or up for a desired station and listen to it, long press one of them to enter MANUAL mode, then briefly press one of them step by step. 3.
During radio operation in one FM frequency band the search for a traffic announcement station is started automatically (TA SEEK) . If an FM station is being received which transmits the latest traffic announcements from time to time, the TP display lights up. If an FM station is being received which transmits the latest traffic announcements automatically interrupt CD operation(the word TRAFFIC appears in the display).
BT Operation 1. Pairing and Connecting Prior to using the BT device named BT CAR STEREO as a handfree system for a BT-enabled mobile phone for the first time, you must pair and connect them as follows: * In any mode, prior to pairing and connecting, the BT logo flashes in the LCD. 1) Press the PAIR button on the control panel to display “PAIRING”(press the BAND button to cancel pairing); 2).
3) Answer a call During ringing, the incoming telephone number displays in the LCD. If you want to receive it, press the button on control panel or press the button on remote control; if you want to reject it, press the button on control panel or press the button on remote control. 4) End phone talking When you want to end phone talking, press the or button.
Disc/USB/card operation 1. Loading or unloading a disc, USB or card 1.1 Loading a disc, USB or card To play files on a disc, insert a disc with label surface up into the disc slot, then it will play automatically. Label surface up * DISCS PRECAUTIONS 1) Handle a disc by its edges, do not touch the surface of play side. 2) Before inserting a disc, wipe the disc outwards from the disc centre with a clean, soft, dry, lint-free cloth. Do not use solvents/thinners such as petrol/benzine or cleaners.
To unload the USB storage, use STOP button to stop playback, then remove the USB storage. To unload the card in the card slot, use STOP button to stop playback. Press REL button to detach the control panel, push the card to release it and then pull it out of the card slot. 2. Function of buttons on main unit or remote control 1. >|| button During playback, use it to pause playback; in pause mode, use it to resume playback. 2.
2) DIR SEARCH: a. Press APS button twice to enter dir search mode and display NAVIGAT on LCD. b. Press the SEL button to display FOLD 00 1 , The 1 is the digit of the folder SN. in units order. after a while, it will display the name of the No. 1 folder. Then rotate the VOL knob or press the VOL+ or VOL- button to select the digit in units order of the folder SN. After selecting the desired digit in units order, press the SEL button to confirm. c. To select all digits of the desired folder SN.as above d.
AUX IN Operation 1. Use an audio cable to connect the car audio system and the external audio system through the AUX IN jack on the control panel of the car audio system and the Audio Out jack of the external audio system. Ground Right Left 2. Play the external audio system, and use the MODE button to enter AUX IN mode for the car audio system. * In AUX IN mode, the external audio system uses the car audio system as an amplifier. 3.
Troubleshooting During playback, if your player has a problem, use this guide to try and resolve the problem .If you are unable to solve the problem,consult an authorised dealer or service centre. Symptom Cause Solution Car ignition is not on.
SPECIFICATIONS GENERAL Power Supply Requirement.............................................DC 12V Current consumption....................................................10A MAX. Maximum Power Output..............4 x 25W(measured at DC 14.4 V) RADIO FM Frequency range.........................................87.5MHz -108.0MHz Usable sensitivity.............................................................15dBu I.F Frequency...............................................................10.
