SP-502CD USER MANUAL CAR AUDIO SYSTEM MUTE PTY VOL+ VOL- DISP PWR MOD SEL AF APS ENTER TA SEARCH SCAN ID3 3 RPT BAND 2 INT 6 +10 /TOP 5 -10 1 4 RDM FLIP DOWN AND REMOVABLE CONTROL PANEL REMOTE CONTROL CONTROL PANEL USB PORT AND AUX INPUT SD Card Slot CD/MP3/WMA DISC PLAYER BUILT-IN AM/FM-RDS TUNER Remark: Any information subject to change without further notice
Content 1. Installation steps.......................................................................... 2 2. General knowledge about remote control ..................................... 6 2.1 Removing insulating sheet......................................................... 6 2.2 Replace lithium cell.................................................................... 6 2.3 Note about using remote control................................................ 6 2.4 Warning for lithium cells of remote control.......
1. INSTALLATION STEPS 1. Remove 2 screws for protecting deck; 1) Remove chassis from Slide Bracket Housing as bellows: KEY PLATE PLASTIC TRIM OUT KEY PLATE If you want to remove chassis from Slide Bracket Housing , first remove Plastic trim out at both sides, then insert 2 Key Plates into left and right side of chassis as above illustration. 2) Remove 2 screws for protecting deck as right; 2.
3) Connecting all wires as bellows: FRONT AUDIO OUT RCA JACK L (white) REAR AUDIO OUT RCA JACK L (white) RADIO ANTENNA JACK FRONT AUDIO OUT RCA JACK R (red) REAR AUDIO OUT RCA JACK R (red) ISO CONNECTOR BLUE AUTO ANTENNA YELLOW CONSTANT 12 VOLTS BLACK GROUND(B-) RED FRONT Lch SPK. REAR FUSE WHITE GREY WHITE/BLACK GREY/BLACK GREEN VIOLET GREEN/BLACK VIOLET/BLACK Lch SPK. IGNITION SWITCH FRONT Rch SPK. REAR Rch SPK. NOTE: 1. Must use 4 ohms impedance of speakers. 2.
4) Attach control panel onto chassis. A. Make the right hollow of control panel aim at the right bulge of chassis, then push and hold control panel rightwards; at one time, move the left end of control panel towards chassis to make the left hollow of control panel aim at the left bulge of chassis and then release holding . Bulge Hollow Bulge Hollow B. Flip control panel up till hearing a click sound to attach onto chassis.
Installation diagram DASH BOARD HEX NUT METAL STRAP SPRING WASHER CONSOLE SLIDE BRACKET HOUSING TAPPING SCREW HEX BOLT -5-
2. General knowledge about remote control 2.1 Removing insulating sheet If using remote control for the first time, you can see an insulating sheet at the bottom side of remote control as right. you must remove the insulating sheet as right. Otherwise, the remote control is disabled. 2.2 Replace lithium cell If the electric energy of lithium cell is weak, replace it. 1.
3. Locations and Names of controls 3.1 Locations and Names of controls on main unit 2 3 6 11 12 7 18 15 1 17 16 8 4 5 10 9 Control panel 19 13 14 Chassis front side after removing control panel 1. OPEN button 10. |<< button 2. PWR button 11. >>| button 3. VOLUME knob 12. MOD button 4. SEL button 13. EJECT button 5. BAND button 14. RESET button 6. TA/AF button 15. IR sensor window 7. APS button 16. AUX IN jack 8. MUTE/PTY button 17. USB port cover 9. >|| or CH1-6 button 18.
3.2 Locations and Names of controls on remote control 1. PWR button 11. VOL+ button 2. < button 12. MUTE button 3. AF button 13. SEL or ENTER button 4. VOL- button 14. > button 5. TA button 15. PTY button 6. ID3 or BAND button 16. DISP button 7. APS or SEARCH button 17. MOD button 8. >|| or TOP or 1 button 18. SCAN button 9. RDM or 4 button 19. RPT or 3 button 10.INT or 2 button 20. +10 or 6 button 21.
4. Conjunct Operation 1. PWR button To power on or off main unit. 2. VOLUME knob or VOL+ & VOL- button To increase or decrease volume level. 3. MUTE button To cancel or resume sound. 4. SEL button To switch between BAS(bass), TRE(treble), BAL(balance) , FAD(fader) and VOL (volume), short press SEL button. After switching on a desired mode, rotate VOLUME knob or press VOL+ or VOL- button to set it.
5. Radio Operation 1. BAND button To switch between FM1,FM2,FM3,MW1 and Mw2. 2. |<< & >>| or < & > buttons In standby mode or after no manually searching operation for a while, briefly press one of them to automatically search down or up for an available station and listen to it. To manually search down or up for a desired station and listen to it, long press one of them to enter MANUAL mode, then briefly press one of them step by step. 3.
7. TA button when you press TA button, TA function is activated, and TA symbol appears in the display . ( press it again to turn off . ) During radio operation in one FM frequency band the search for a traffic announcement station is started automatically (TA SEEK) . If an FM station is being received which transmits the latest traffic announcements from time to time, the TP display lights up.
6. Disc/USB/card operation 6.1 Loading or unloading a disc, USB or card 6.1.1 Loading a disc, USB or card To play files in a disc, press OPEN button to flip down control panel, then insert a disc with label surface up into disc slot, and then attach control panel onto chassis again, by now it will automatically play. Label surface up * CAUTION OF USING DISC 1) Handle a disc by its edge, do not touch the surface of play side.
To pull away the USB bar, use STOP button to stop playback, then you can remove the USB bar. To unload the card in card slot, use STOP button to stop playback, then press OPEN button to flip down control panel and then remove it, and then you can push the card and pull it out of card slot. 6.2 Function of buttons on main unit or remote control 1. >|| button During playback, use it to pause playback; in pause mode, use it to resume playback. 2.
b. When displaying TOL #(folder max. SN.), rotate VOLUME knob or press VOL+ or VOL- button to select folder name. c. After selecting a desired folder, press SEL or ENTER button to play the first track in the folder, and then use >>| & > or |<< & < buttons to select a desired file to play. 4. INT button To switch on or off INT mode. 5. RPT button During CD playback, it can switch repeat function between RPT ONE or RPT ALL.
8. Trouble Shooting During playback, if your player has some problem, solve it according to the following list. If you can not solve it by the list, consult your nearest service dealer. Symptom Cause Solution Car ignition is not on.
9. SPECIFICATION GENERAL Power Supply Requirement.............................................DC 12V Current consumption....................................................10A MAX. Maximum Power Output..............4 x 25W(measured at DC 14.4 V) Dimensions(w x h x d).......................................178 x 50 x 155mm RADIO FM Frequency range.........................................87.5MHz -108.0MHz Usable sensitivity.............................................................15dBu I.F Frequency.......
