User's Manual

REV 09/02
Page 2 of
Flip open the plastic cover on the front of the transmitter to expose the “SET” buttons. The flip cover
protects the SET buttons from being changed accidentally. Close the cover after completing the
following settings/ programming.
Flashing numbers on the display indicate the system is awaiting user input, such as using the UP and
DOWN buttons to program a new setting. If no change is made to flashing digits within 15 seconds,
the system will complete the procedure last programmed and reset the display to its normal state.
1. Press and hold the TIME button on the transmitter for more than two seconds. The hour digit(s)
will begin flashing.
2. Press the UP or DOWN button until the desired hour is displayed in AM or PM.
3. After setting the desired hour, press and release the TIME button again to set the minutes ; the
minute digits will begin flashing.
4. Press the UP or DOWN button until the desire minutes are displayed.
5. After setting the desired hour and minutes press the SET button on the transmitter to stop the
minutes digits from flashing and the time is set.
SETTING
0
F /
0
C SCALE
The factory setting for temperature is
0
F. To change this setting to
0
C,
first press and hold the UP button on the transmitter, then press the
DOWN button. Follow this same procedure to change from
0
C back to
0
F. When changing between the
0
F and
0
C scales, the
temperature in the SET frame defaults to the lowest temperature (45
0
F, or 6
0
C ).
SETTING DESIRED ROOM TEMPERATURE
This remote control system can be thermostatically controlled when the transmitter is in the THERMO
mode (THERMO must be displayed on the screen). To set the DESIRED room temperature, press
the MODE button to place the transmitter into THERMO mode, then press the UP or DOWN button to
select the desired room temperature. The highest SET temperature is 99
0
Fahrenheit (32
0
Celsius).
The lowest SET temperature is 45
0
Fahrenheit (6
0
Celsius).
OPERATIONAL NOTE: TO CONSERVE BATTERY POWER, CHANGES IN ROOM
TEMPERATURE ARE ONLY UPDATED EVERY TWO MINUTES.
The Thermo Mode on the transmitter operates the appliance when ever the ROOM TEMPERATURE varies a certain number of degrees
from the SET TEMPERATURE. This variation is called the “SWING” or TEMPERATURE DIFFERENTIAL. The normal operating cycle of
an appliance may be 2-4 times per hour depending on how well the room or home is insulated from the cold or drafts. The factory setting
for the “swing number” is (2). This represents a temperature variation of +/- 2
0
F (1
0
C between SET temperature and ROOM
temperature, which determines when the fireplace will be activated.
SETTING THE COUNTDOWN TIMER
This remote control system can operate with a built-in countdown timer when the transmitter is in the
ON or THERMO modes (THERMO or ON must be displayed on the screen).
1. Press and release the TIMER button on the transmitter. 0:15 will begin to flash in the timer box
on the screen.
2. Press the UP or DOWN button on the transmitter to begin advancing through each of the
countdown time options. Available countdown times are 15 minutes, 30 minutes, 45 minutes, 1
hour, 1 hour 30 minutes, 2 hours, 2 hours 30 minutes, and each additional half-hour up to nine
hours.
3. To set the TIMER press the SET button on the transmitter if the system is ON, it will remain on
until the “time “
has expired. If the system is in the THERMO mode, it will cycle on and off as
the room temperature requires until the “time” has expired.
TIMER
BUTTON SETTINGS
MODE
SET TIME
UP
DOWN
CODE
SETTING THE CLOCK
ON
ROOM
L
O
W
OFF
TIMER
THERMO
SET
PM
FLAME
ON
ROOM
L
O
W
OFF
TIMER
THERMO
SET
PM
FLAME
ON
ROOM
L
O
W
OFF
TIMER
THERMO
SET
PM
FLAME
ON
ROOM
L
O
W
OFF
TIMER
THERMO
SET
PM
FLAME
ON
ROOM
L
O
W
OFFTIMER
THERMO
SET
PM
FLAME
ON
ROOM
L
O
W
OFFTIMER
THERMO
SET
PM
FLAME