SUPER ® SUPERSERVER 6014P-8 SUPERSERVER 6014P-8R SUPERSERVER 6014P-82R SUPERSERVER 6014P-82 USER’S MANUAL 1.
The information in this User’s Manual has been carefully reviewed and is believed to be accurate. The vendor assumes no responsibility for any inaccuracies that may be contained in this document, makes no commitment to update or to keep current the information in this manual, or to notify any person or organization of the updates. Please Note: For the most up-to-date version of this manual, please see our web site at www.supermicro.com.
Preface Preface About This Manual This manual is written for professional system integrators and PC technicians. It provides information for the installation and use of the SuperServer 6014P-8/6014P-8R/6014P-82R/6014P-82. Installation and maintainance should be performed by experienced technicians only.
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual Chapter 4: System Safety You should thoroughly familiarize yourself with this chapter for a general overview of safety precautions that should be followed when installing and servicing the SuperServer 6014P-8/6014P-8R/6014P-82R/6014P-82. Chapter 5: Advanced Serverboard Setup Chapter 5 provides detailed information on the X6DHP-8G/X6DHP-8G2 serverboard, including the locations and functions of connections, headers and jumpers.
Preface Notes v
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual Table of Contents Preface About This Manual ...................................................................................................... iii Manual Organization ................................................................................................... iii Chapter 1: Introduction 1-1 Overview .........................................................................................................
Table of Contents Chapter 5: Advanced Serverboard Setup 5-1 Handling the Serverboard ............................................................................. 5-1 5-2 Processor and Heatsink Installation ............................................................ 5-2 5-3 Connecting Cables ......................................................................................... 5-5 Connecting Data Cables .........................................................................
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual GLAN Enable/Disable ............................................................................. 5-20 VGA Enable/Disable .............................................................................. 5-21 SCSI Controller Enable/Disable ............................................................ 5-21 SCSI Termination Enable/Disable ......................................................... 5-21 DOC IDE Slot Bus Speed Select ......................
Table of Contents Appendices: Appendix A: BIOS POST Codes ............................................................................ A - 1 Appendix B: Software Installation ......................................................................... B-1 Appendix C: System Specifications ......................................................................
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual Notes x
Chapter 1: Introduction Chapter 1 Introduction 1-1 Overview The SuperServer 6014P-8/6014P-8R/6014P-82R/6014P-82 is a high-end server comprised of two main subsystems: the SC814+S-560/SC814+SR560 1U server chassis and the X6DHP-8G/X6DHP-8G2 dual processor serverboard. Please refer to our web site for information on operating systems that have been certified for use with the SuperServer 6014P-8/ 6014P-8R/6014P-82R/6014P-82 (www.supermicro.com).
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual z 1U passive heatsink (SNK-P0009, optional) z One (1) CD containing drivers and utilities z SuperServer 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual 1-2 Serverboard Features At the heart of the SuperServer 6014P-8/6014P-8R/6014P-82R/6014P-82 lies the X6DHP-8G/X6DHP-8G2, a dual processor serverboard based on Intel's E7520 chipset. Below are the main features of the X6DHP-8G/X6DHP8G2 (see Figure 1-1 for a block diagram of the chipset).
Chapter 1: Introduction ATI Graphics Controller The X6DHP-8G/X6DHP-8G2 features an integrated ATI video controller based on the Rage XL graphics chip. Rage XL fully supports sideband addressing and AGP texturing. This onboard graphics package can provide a bandwidth of up to 512 MB/sec over a 32-bit graphics memory bus.
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual PCI Expansion Slots 6014P-8/6014P-82: supports the use of two standard size PCI-X (one 133 and one 100 MHz) add-on cards or two standard size PCI-Express x8 addon cards (with riser cards). See section 5-6 for details on riser cards. 6014P-8R/6014P-82R: supports the use of one standard size 133 MHz PCIX or PCI-Express x8 add-on card (with riser card). See section 5-6 for details on riser cards.
Chapter 1: Introduction Figure 1-1. Intel E7520 Chipset: System Block Diagram Note: This is a general block diagram. Please see Chapter 5 for details.
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual 1-4 Contacting Supermicro Headquarters Address: Tel: Fax: Email: Web Site: SuperMicro Computer, Inc. 980 Rock Ave. San Jose, CA 95131 U.S.A. +1 (408) 503-8000 +1 (408) 503-8008 marketing@supermicro.com (General Information) support@supermicro.com (Technical Support) www.supermicro.com Europe Address: Tel: Fax: Email: SuperMicro Computer B.V.
Chapter 2: Server Installation Chapter 2 Server Installation 2-1 Overview This chapter provides a quick setup checklist to get your SuperServer 6014P-8/6014P-8R/6014P-82R/6014P-82 up and running. Following these steps in the order given should enable you to have the system operational within a minimum amount of time. This quick setup assumes that your system has come to you with the processors and memory preinstalled.
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual Choosing a Setup Location - Leave enough clearance in front of the rack to enable you to open the front door completely (~25 inches). - Leave approximately 30 inches of clearance in the back of the rack to allow for sufficient airflow and ease in servicing. ! Warnings and Precautions! ! Rack Precautions - Ensure that the leveling jacks on the bottom of the rack are fully extended to the floor with the full weight of the rack resting on them.
Chapter 2: Server Installation Rack Mounting Considerations Ambient Operating Temperature If installed in a closed or multi-unit rack assembly, the ambient operating temperature of the rack environment may be greater than the ambient temperature of the room. Therefore, consideration should be given to installing the equipment in an environment compatible with the manufacturer’s maximum rated ambient temperature (Tmra).
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual 2-4 Installing the System into a Rack This section provides information on installing the system into a rack unit with the rack rails provided. If the system has already been mounted into a rack, you can skip ahead to Sections 2-5 and 2-6. There are a variety of rack units on the market, which may mean the assembly procedure will differ slightly. You should also refer to the installation instructions that came with the rack unit you are using.
Chapter 2: Server Installation Installing the Rack Rails Begin by joining together the front and rear rack rails. Do this by inserting the standoffs from one rail into the grooves of the other rail and then pulling the rails in opposite directions so that the standoffs slide into the narrow part of the groove. Take this assembly and hold it up to the rack (at the desired height) to determine the proper length - the standoffs/groove allows you to adjust the length of the rail to fit the depth of the rack.
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual Installing the Server into the Rack You should now have rails attached to both the chassis and the rack unit. The next step is to install the server into the rack. Do this by lining up the rear of the chassis rails with the front of the rack rails. Slide the chassis rails into the rack rails, keeping the pressure even on both sides (you may have to depress the locking tabs when inserting). See Figure 2-3.
Chapter 2: Server Installation Installing the Server into a Telco Rack If you are installing the SuperServer 6014P-8/6014P-8R into a Telco type rack, follow the directions given on the previous pages for rack installation. The only difference in the installation procedure will be the positioning of the rack brackets to the rack. They should be spaced apart just enough to accommodate the width of the telco rack. Figure 2-4.
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual 2-5 Checking the Serverboard Setup After you install the 6014P-8/6014P-8R/6014P-82R/6014P-82 in the rack, you will need to open the top cover to make sure the serverboard is properly installed and all the connections have been made. 1. Accessing the inside of the System (see Figure 2-5) First, release the retention screws that secure the system to the rack.
Chapter 2: Server Installation Figure 2-5.
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual 2-6 Checking the Drive Bay Setup Next, you should check to make sure the peripheral drives and the SCSI drives and SCSI backplane have been properly installed and all connections have been made. 1. Accessing the drive bays All drives are accessable from the front of the server. For servicing the DVD-ROM and floppy drives, you will need to remove the top chassis cover.
Chapter 3: System Interface Chapter 3 System Interface 3-1 Overview There are several LEDs on the chassis control panel as well as others on the SCSI drive carriers to keep you constantly informed of the overall status of the system as well as the activity and health of specific components. There are also two buttons on the chassis control panel. This chapter explains the meanings of all LED indicators and the appropriate response you may need to take.
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual 3-3 Control Panel LEDs The control panel located on the front of the SC814+S-560/SC814+S-R560 chassis has six LEDs, which provide you with critical information related to different parts of the system. This section explains what each LED indicates when illuminated and any corrective action you may need to take. z UID: This LED turns on when either the front or the rear UID button is pushed.
Chapter 3: System Interface HDD: Indicates hard drive activity. On the SuperServer 6014P-8/ z 6014P-8R/6014P-82R/6014P-82 this light indicates SCSI and/or DVD-ROM drive activity when flashing. z Power: Indicates power is being supplied to the system's power supply module(s). With the 6014P-8/6014P-82, this LED should always be green when the system is operating. On the 6014P-8R/6014P-82R, this LED turns amber in the event of a power supply failure or if a power supply cord is disconnected or loose.
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual Notes 3-4
Chapter 4: System Safety Chapter 4 System Safety 4-1 Electrical Safety Precautions ! Basic electrical safety precautions should be followed to protect yourself from harm and the system from damage: z Be aware of the locations of the power on/off switch on the chassis as well as the room's emergency power-off switch, disconnection switch or electrical outlet. If an electrical accident occurs, you can then quickly remove power from the system. z Do not work alone when working with high voltage components.
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual z The power supply power cord must include a grounding plug and must be plugged into grounded electrical outlets. z Serverboard Battery: CAUTION - There is a danger of explosion if the onboard battery is installed upside down, which will reverse its polarities. This battery must be replaced only with the same or an equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions.
Chapter 4: System Safety power is present. z After accessing the inside of the system, close the system back up and secure it to the rack unit with the retention screws after ensuring that all connections have been made. 4-3 ESD Precautions ! Electrostatic discharge (ESD) is generated by two objects with different electrical charges coming into contact with each other. An electrical discharge is created to neutralize this difference, which can damage electronic components and printed circuit boards.
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual 4-4 Operating Precautions ! Care must be taken to assure that the chassis cover is in place when the 6014P-8/6014P-8R/6014P-82R/6014P-82 is operating to ensure proper cooling. Out of warranty damage to the 6014P-8/6014P-8R/6014P-82R/ 6014P-82 system can occur if this practice is not strictly followed. Figure 4-1.
Chapter 5: Advanced Serverboard Setup Chapter 5 Advanced Serverboard Setup This chapter covers the steps required to install processors, memory and heatsinks to the X6DHP-8G/X6DHP-8G2 serverboard, connect the data and power cables and install add-on cards. All serverboard jumpers and connections are described and a layout and quick reference chart are included in this chapter. Remember to close the chassis completely when you have finished working on the serverboard to protect and cool the system.
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual 5-2 Processor and Heatsink Installation ! When handling the processor pressure on the label area of motherboard on a conductive BIOS battery and prevent the package, avoid placing direct the fan. Also, do not place the surface, which can damage the system from booting up. IMPORTANT: Always connect the power cord last and always remove it before adding, removing or changing any hardware components.
Chapter 5: Advanced Serverboard Setup Figure 5-1. 604-pin PGA Socket: Empty and with Processor Installed Warning! ! Make sure you lift the lever completely when installing the CPU. If the lever is only partly raised, damage to the socket or CPU may result. Empty socket With processor installed Lever Triangle (pin 1) Triangle locating pin 1 Heatsink Installation 1. Do not apply any thermal compound to the heatsink or the CPU die; the required amount has already been applied. 2.
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual Removing the Heatsink/CPU ! IMPORTANT: Removal of the heatsink or the CPU is not recommended. However, if you do need to remove the heatsink, please follow the instructions below to prevent damaging the CPU or the CPU socket. 1. Unscrew and remove the heatsink screws from the serverboard in the sequence used when installing (diagonal screws). 2. Grasp the heatsink and gently wriggle it to loosen it from the CPU.
Chapter 5: Advanced Serverboard Setup 5-3 Connecting Cables Now that the processors are installed, the next step is to connect the cables to the serverboard. These include the data (ribbon) cables for the peripherals and control panel and the power cables. Connecting Data Cables The ribbon cables used to transfer data from the peripheral devices have been carefully routed in preconfigured systems to prevent them from blocking the flow of cooling air that moves through the system from front to back.
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual Connecting the Control Panel JF1 contains header pins for various front control panel connectors. See Figure 5-3 for the pin locations of the various front control panel buttons and LED indicators. Please note that even and odd numbered pins are on opposite sides of each header. All JF1 wires have been bundled into single ribbon cable to simplify their connection. Make sure the red wire plugs into pin 1 as marked on the board.
Chapter 5: Advanced Serverboard Setup 5-4 I/O Ports The I/O ports are color coded in conformance with the PC 99 specification. See Figure 5-4 below for the colors and locations of the various I/O ports. Figure 5-4. I/O Ports 5-5 Installing Memory Note: Check the Supermicro web site for recommended memory modules: http://www.supermicro.com/support/resources/ CAUTION Exercise extreme care when installing or removing DIMM modules to prevent any possible damage.
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual X6DHP-8G2: eight 240-pin DIMM slots that can support up to 16 GB of registered ECC DDR2-400 SDRAM. Both serverboards are designed to support 2 GB modules in each socket, but have only been verified for up to 1 GB modules. Both employ an interleaved memory configuration, which requires modules of the same size and speed to be installed in pairs. You should not mix modules of different sizes and/or speeds.
Chapter 5: Advanced Serverboard Setup 5-6 Adding PCI Cards 1. PCI slots Your system should come with one or two riser cards to acommodate the use of one or two PCI expansion cards. The number and type of cards supported by each server system is shown below. 6014P-8/6014P-82: supports the use of one standard size (full-height fulllength) 133 and 100 MHz PCI-X add-on cards or two PCI-Express x8 add-on cards or a combination thereof (with a maximum of one PCI-X 133 card).
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual Serverboard Details Figure 5-6.
Chapter 5: Advanced Serverboard Setup X6DHP-8G Quick Reference Jumper Description Default Setting JP17/JP18 JPA1 JPA2 JPA3 JBT1 JPG1 JPL1 JWD1 XJ4F1/XJ4F2* DOC1/2 IDE Bus Select SCSI Enable/Disable SCSI Channel A Termination Enable SCSI Channel B Termination Enable CMOS Clear VGA Enable/Disable GLAN Enable/Disable Watch Dog Memory Speed Select Closed (Master) Pins 1-2 (Enabled) Off (Enabled) Off (Enabled) See Section 5-9 Pins 1-2 (Enabled) Pins 1-2 (Enabled) Pins 1-2 (Reset) Closed (DDR333) Connector
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual Figure 5-7. SUPER X6DHP-8G2 Layout (not drawn to scale) UID Mouse Keyboard VGA SCSI CH B JA2 JLAN2 JLAN1 USB0/1 BIOS JPA3 JPA1 JPL1 Battery J22 JPG1 GLAN Controller ATI Rage XL SCSI Controller SCSI CH A PCI-E x8 PCI-E x8 DA2 DA1 COM1 PHX JWOR1 JWD1 J27 JBT1 Note: a PCI-X slot and a PCI-E slot together constitute a Universal PCI slot.
Chapter 5: Advanced Serverboard Setup X6DHP-8G2 Quick Reference Jumper Description Default Setting JP17/JP18 JPA1 JPA2 JPA3 JBT1 JPG1 JPL1 JWD1 DOC1/2 IDE Bus Select SCSI Enable/Disable SCSI Channel A Termination Enable SCSI Channel B Termination Enable CMOS Clear VGA Enable/Disable GLAN Enable/Disable Watch Dog Closed (Master) Pins 1-2 (Enabled) Off (Enabled) Off (Enabled) See Section 5-9 Pins 1-2 (Enabled) Pins 1-2 (Enabled) Pins 1-2 (Reset) Connector Description 1U IPMI COM1/COM DA1/DA2 FAN 1-10
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual 5-8 Connector Definitions ATX Power Connector The X6DHP-8G/X6DHP-8G2 includes a 24-pin main power supply connector (JPW1) that meets the SSI (Superset ATX) specification. You can only use a 24-pin power supply cable on the motherboard. Make sure that the orientation of the connector is correct. See the table on the right for pin definitions.
Chapter 5: Advanced Serverboard Setup HDD LED HDD LED Pin Definitions (JF1) The HDD LED (for IDE and SCSI drives) connection is located on pins 13 and 14 of JF1. Attach the drive LED cable to these pins to display disk activity. See the table on the right for pin definitions. Pin Number Definition Vcc 13 HD Active 14 NIC1/2 LEDs The NIC (Network Interface Controller) LED connections for GLAN1 are located on pins 11 and 12 of JF1 and the NIC LED connections for GLAN2 are located on pins 9 and 10 of JF1.
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual UID Button & UID LED A Unit Identifier button/LED is located next to the VGA port on the rear of the chassis and a UID LED and button (separate) are located on the front control panel. The UID LED connection is located on pins 3 and 4 of JF1. Refer to the table on the right for pin definitions and to page 5-21 for details. Power Button The Power Button connection is located on pins 1 and 2 of JF1.
Chapter 5: Advanced Serverboard Setup Universal Serial Bus (USB0/1) Universal Serial Bus Pin Definitions USB0 USB1 Two USB 2.0 ports are located beside the GLAN (Ethernet) ports. USB0 is the bottom port and USB1 is the top port. See the table on the right for pin definitions.
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual Power LED/Speaker Speaker Connector Pin Definitions (JD1) On the JDI header, pins 1-3 are for a power LED and pins 4-7 are for the speaker. See the table on the right for speaker pin definitions. Pin Number Function Definition 4 + Red wire, Speaker data 5 Key No connection 6 Key 7 Speaker data Note: The speaker connector pins are for use with an external speaker. If you wish to use the onboard speaker, you should close pins 6-7 with a jumper.
Chapter 5: Advanced Serverboard Setup SMB SMB Header Pin Definitions (J22) A System Management Bus header is located at J22. Connect the appropriate cable here to utilize SMB on your system. SMB Power Connector Pin Number 1 2 3 4 Definition Data Ground Clock No Connection SMB PWR Pin Definitions (J24) Connect the SMB power connector to J24 (located near the ATX power connector) to utilize SMB.
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual 5-9 Jumper Settings Explanation of Jumpers 3 2 1 3 2 1 Connector Pins To modify the operation of the serverboard, jumpers can be used to choose between optional settings. Jumpers create shorts between two pins to change the function of the connector. Pin 1 is identified with a square solder pad on the printed circuit board. See the serverboard layout pages for jumper locations.
Chapter 5: Advanced Serverboard Setup VGA Enable/Disable JPG1 enables or disables the VGA port on the serverboard. See the table on the right for jumper settings. SCSI Controller Enable/ Disable VGA Enable/Disable Jumper Settings (JPG1) Jumper Position Pins 1-2 Pins 2-3 Definition Enabled Disabled SCSI Enable/Disable Jumper Settings (JPA1) Jumper JPA1 allows you to enable or disable the SCSI headers. The default setting is pins 1-2 to enable all four headers.
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual Watch Dog Watch Dog Jumper Settings (JWD1) JWD1 controls Watch Dog, a system monitor that takes action when a software application freezes the system. Jumping pins 1-2 will cause WD to reset the system if an application is hung up. Jumping pins 2-3 will generate a non-maskable interrupt signal for the application that is hung up. See the table on the right for jumper settings. Watch Dog can also be enabled via BIOS.
Chapter 5: Advanced Serverboard Setup 5-10 Onboard Indicators GLAN LEDs Speed LED Activity LED The Gigabit Ethernet LAN ports (located beside the VGA port) each have two LEDs. The left LED indicates activity while the right LED may be green, amber or off to indicate the speed of the connection. See table at right for the functions associated with the second LED.
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual 5-11 Floppy/Hard Disk and SCSI Drive Connections Note the following when connecting the floppy and hard disk drive cables: • The floppy disk drive cable has seven twisted wires. • A red mark on a wire typically designates the location of pin 1. • A single floppy disk drive ribbon cable has 34 wires and two connectors to provide for two floppy disk drives.
Chapter 5: Advanced Serverboard Setup Ultra320 SCSI Connectors Refer to the table below for the pin definitions of the Ultra320 SCSI connectors located at JA1 and JA2.
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual Notes 5-26
Chapter 6: Advanced Chassis Setup Chapter 6 Advanced Chassis Setup This chapter covers the steps required to install components and perform maintenance on the SC814+S-560/SC814+S-R560 chassis. For component installation, follow the steps in the order given to eliminate the most common problems encountered. If some steps are unnecessary, skip ahead to the next step. Tools Required The only tool you will need to install components and perform maintenance is a Philips screwdriver.
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual Figure 6-1.
Chapter 6: Advanced Chassis Setup 6-3 System Fans Five 4-cm fans provide the cooling for the 6014P-8/6014P-8R/6014P-82R/ 6014P-82. Each fan unit is actually made up of two fans joined back-toback, which rotate in opposite directions. This counter-rotating action generates exceptional airflow and works to dampen vibration levels. These fans can adjust their speed according to the heat level sensed in the system, which results in more efficient and quieter fan operation.
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual Figure 6-2. 6-4 Removing the Fan Housing Drive Bay Installation/Removal Accessing the Drive Bays SCSI Drives: Because of their hotswap capability, you do not need to access the inside of the chassis or power down the system to install or replace SCSI drives. Proceed to the next step for instructions.
Chapter 6: Advanced Chassis Setup SCSI Drive Installation 1. Mounting a SCSI drive in a drive carrier The SCSI drives are mounted in drive carriers to simplify their installation and removal from the chassis. These carriers also help promote proper airflow for the SCSI drive bays. For this reason, even empty carriers without SCSI drives installed must remain in the chassis.
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual 2. Installing/removing hot-swap SCSI drive carrier The SCSI drive bays are located in the front of the chassis, making them easily accessible for installation and removal. The SCSI drives are hotswap units, meaning that they can be installed and removed while the system is running.
Chapter 6: Advanced Chassis Setup DVD-ROM and Floppy Drive Installation The top cover of the chassis must be opened to gain full access to the DVD-ROM and floppy drive bays. The 6014P-8/6014P-8R/6014P-82R/6014P82 accomodates only slim DVD-ROM and floppy drives. Side mounting brackets are needed to mount a slim DVD-ROM drive in the server. You must power down the system before installing or removing a floppy or DVD-ROM drive. First, release the retention screws that secure the server unit to the rack.
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual 6-5 Power Supply 6014P-8R/6014P-82R The SuperServer 6014P-8R/6014P-82R has a redundant 560 watt redundant power supply configuration consisting of two hot-swappable power modules. Each power supply module has an auto-switching capability, which enables it to automatically sense and operate with a 100V - 240V input voltage.
Chapter 6: Advanced Chassis Setup 6014P-8/6014P-82 The SuperServer 6014P-8/6014P-82 has a single 560 watt cold-swap power supply, which is auto-switching capable. This enables it to automatically sense and operate with a 100v - 240v input voltage. An amber light will be illuminated on the power supply when the power is off. An illuminated green light indicates that the power supply is operating.
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual Figure 6-5. Removing/Replacing the Power Supply Reconfiguring the Power Supply Although the standard configuration for the 6014P-8/6014P-82 and 6014P8R/6014P-82R is with single and dual (redundant) power supplies respectively, you can reconfigure the 6014P-8/6014P-82 to hold two power supply modules or (not recommended) the 6014P-8R/6014P-82R to hold a single power supply module.
Chapter 6: Advanced Chassis Setup 4. At the rear of the power distribution board (where the second power supply is inserted), there is a vertical shield that protects the second power supply slot. Remove this shield by grasping and forcibly pulling it off the cover that protects the power distribution board. 5. Remove the COM port header from the backpanel while keeping it connected to the serverboard. 6.
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual 3. Remove the COM port header from the backpanel while keeping it connected to the serverboard. 4. Remove the three screws (two on the bottom and one on the side) that secure the right backpanel section to the chassis, then remove the backpanel section (Figure 6-6, step 2). Locate the alternate backpanel section and attach it to the backpanel with the same screws you just removed (Figure 6-6, step 1). 5.
Chapter 6: Advanced Chassis Setup Figure 6-6.
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual Notes 6-14
Chapter 7: BIOS Chapter 7 BIOS 7-1 Introduction This chapter describes the Phoenix BIOS™ Setup utility for the X6DHP-8G/ X6DHP-8G2. The Phoenix ROM BIOS is stored in a flash chip and can be easily upgraded using a floppy disk-based program. Due to periodic changes in the BIOS, some settings may have been added or deleted that might not yet be recorded in this manual. Please refer to the Manual Download area of the Supermicro web site (www.supermicro.com) for any such changes.
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual 7-2 Running Setup *Default settings are in bold text unless otherwise noted. The BIOS setup options described in this section are selected by choosing the appropriate text from the main BIOS Setup screen. All displayed text is described in this section, although the screen display is often all you need to understand how to set the options (see on next page). When you first power on the computer, the Phoenix BIOS™ is immediately activated.
Chapter 7: BIOS Main BIOS Setup Menu Main Setup Features System Time To set the system date and time, key in the correct information in the appropriate fields. Then press the key to save the data. System Date Using the arrow keys, highlight the month, day and year fields and enter the correct data. Press the key to save the data. BIOS Date This feature allows BIOS to automatically display the BIOS date.
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual Legacy Diskette A This setting allows the user to set the type of floppy disk drive installed as diskette A. The options are Disabled, 360Kb 5.25 in, 1.2MB 5.25 in, 720Kb 3.5 in, 1.44/1.25MB, 3.5 in and 2.88MB 3.5 in. Parallel ATA This setting allows the user to enable or disable the function of Parallel ATA. The options are Disabled, Channel 0, Channel 1 and Both.
Chapter 7: BIOS IDE Channel 0 Master/Slave, IDE Channel 1 Master/Slave, IDE Channel 2 Master, IDE Channel 3 Master These settings allow the user to set the parameters of IDE Channel 0 Master/Slave, IDE Channel 1 Master/Slave, IDE Channel 2 Master, IDE Channel 3 Master slots. Hit to activate the following sub-menu screen for detailed options of these items. Set the correct configurations accordingly. The items included in the sub-menu are: Type Selects the type of IDE hard drive.
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual Multi-Sector Transfer This item allows the user to specify the number of sectors per block to be used in multi-sector transfer. The options are Disabled, 4 Sectors, 8 Sectors and 16 Sectors. LBA Mode Control This item determines whether Phoenix BIOS will access the IDE Channel 0 Master Device via the LBA mode. The options are Enabled and Disabled. 32 Bit I/O This option allows the user to enable or disable the function of 32-bit data transfer.
Chapter 7: BIOS 7-4 Advanced Setup Choose Advanced from the Phoenix BIOS Setup Utility main menu with the arrow keys. You should see the following display. The items with a triangle beside them have sub menus that can be accessed by highlighting the item and pressing . Options for PIR settings are displayed by highlighting the setting option using the arrow keys and pressing . All Advanced BIOS Setup options are described in this section.
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual ACPI Mode Use the setting to determine if you want to employ ACPI (Advanced Configuration and Power Interface) power management on your system. The options are Yes and No. Power Button Behavior If set to Instant-Off, the system will power off immediately as soon as the user hits the power button. If set to 4-sec., the system will power off when the user presses the power button for 4 seconds or longer.
Chapter 7: BIOS Cache Base 0-512K If enabled, this feature will allow the data stored in the base memory area: block 0-512K to be cached (written) into a buffer, a storage area in the Static DRM (SDROM) or to be written into L1, L2 cache inside the CPU to speed up CPU operations . Select "Uncached" to disable this funciton. Select "Write Through" to allow data to be cached into the buffer and written into the system memory at the same time.
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual PCI Configuration Access the submenu to make changes to the following settings for PCI devices. Onboard GLAN (Gigabit- LAN) OPROM Configure Enabling this option provides the capability to boot from GLAN. options are Disabled and Enabled. The Reset Configuration Data If set to Yes, this setting clears the Extended System Configuration Data(ESCD) area. The options are Yes and No.
Chapter 7: BIOS Enable Master This setting allows you to enable the selected device as the PCI bus master. The options are Enabled and Disabled. Latency Timer This setting allows you to set the clock rate for Bus Master. A highpriority, high-throughout device may benefit from a greater Clock rate. The options are Default, 0020h, 0040h, 0060h, 0080h, 00A0h, 00C0h, and 00E0h. For Unix, Novell and other Operating Systems, please select the option: other.
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual DRAM Data Integrity Mode If enabled, this feature allows the data stored in the DRMA memory to be integrated for faster data processing. The options are 72-bit ECC, 144-bit ECC, Auto and Disabled. ECC Error Type This setting lets you select which type of interrupt to be activated as a result of an ECC error. The options are None, NMI (Non-Maskable Interrupt), SMI (System Management Interrupt) and SCI (System Control Interrupt.
Chapter 7: BIOS Adjacent Cache Line Prefetch The CPU fetches the cache line for 64 bytes if Disabled. The CPU fetches both cache lines for 128 bytes as comprised if Enabled. I/O Device Configuration Access the submenu to make changes to the following settings. KBC Clock input This setting allows you to set the clock frequency for the Keyboard Clock. The options are 8MHz, 12 MHz and 16MHz. Onboard COM1 This setting allows you to assign control of Onboard COM1.
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual Floppy Disk Controller This setting allows you to assign control of the floppy disk controller. The options are Enabled (user defined), Disabled, and Auto (BIOS and OS controlled). DMI Event Logging Access the submenu to make changes to the following settings. Event Log Validity This is a display to inform you of the event log validity. It is not a setting. Event Log Capacity This is a display to inform you of the event log capacity.
Chapter 7: BIOS Console Redirection Access the submenu to make changes to the following settings. COM Port Address This item allows you to specifies to redirect the console to Onboard COM A or Onboard COM B. This setting can also be Disabled. BAUD Rate This item allows you to select the BAUD rate for console redirection. The options are 300, 1200, 2400, 9600, 19.2K, 38.4K, 57.6K and 115.2K.
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual Hardware Monitor Logic CPU Temperature Threshold This option allows the user to set a CPU temperature threshold that will activate the alarm system when the CPU temperature reaches this pre-set temperature threshold. The options are 85 oC, 90 o C, 95oC and 100oC. Highlight this and hit to see the data for the following items: Temperature: Display the temperature status of the following items.
Chapter 7: BIOS P3V3 P5V P1V8 P2V5 HECETA_MEM_VTT PIVO_NIC N12V_Scaled P3V3_STBY 7-17
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual 7-5 Security Choose Security from the Phoenix BIOS Setup Utility main menu with the arrow keys. You should see the following display. Security setting options are displayed by highlighting the setting using the arrow keys and pressing . All Security BIOS settings are described in this section. Supervisor Password Is: This displays whether a supervisor password has been entered for the system.
Chapter 7: BIOS Set Supervisor Password When the item "Set Supervisor Password" is highlighted, hit the key. When prompted, type the Supervisor's password in the dialogue box to set or to change supervisor's password, which allows access to BIOS. Set User Password When the item "Set User Password" is highlighted, hit the key. When prompted, type the user's password in the dialogue box to set or to change the user's password, which allows access to the system at bootup.
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual 7-6 Boot Choose Boot from the Phoenix BIOS Setup Utility main menu with the arrow keys. You should see the following display. Highlighting a setting with a + or - will expand or collapse that entry. See details on how to change the order and specs of boot devices in the Item Specific Help window. All Boot BIOS settings are described in this section. +Removable Devices Highlight and press to expand the field.
Chapter 7: BIOS 7-7 Exit Choose Exit from the Phoenix BIOS Setup Utility main menu with the arrow keys. You should see the following display. All Exit BIOS settings are described in this section. Exit Saving Changes Highlight this item and hit to save any changes you made and to exit the BIOS Setup utility. Exit Discarding Changes Highlight this item and hit to exit the BIOS Setup utility without saving any changes you may have made.
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual Discard Changes Highlight this item and hit to discard (cancel) any changes you made. You will remain in the Setup utility. Save Changes Highlight this item and hit to save any changes you made. You will remain in the Setup utility.
Appendix A: BIOS POST Codes Appendix A BIOS POST Codes This section lists the POST (Power On Self Test) codes for the PhoenixBIOS. POST codes are divided into two categories: recoverable and terminal. Recoverable POST Errors When a recoverable type of error occurs during POST, the BIOS will display a POST code that describes the problem.
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual POST Code 18h 1Ah 1Ch 20h 22h 24h 28h 29h 2Ah 2Ch 2Eh 2Fh 32h 33h 36h 38h 3Ah 3Ch 3Dh 41h 42h 45h 46h 47h 48h 49h 4Ah 4Bh 4Ch 4Eh 4Fh 50h 51h 52h 54h 55h 58h 59h 5Ah 5Bh Description 8254 timer initialization 8237 DMA controller initialization Reset Programmable Interrupt Controller 1-3-1-1 Test DRAM refresh 1-3-1-3 Test 8742 Keyboard Controller Set ES segment register to 4 GB Auto size DRAM Initialize POST Memory Manager Clear 512 kB base RAM 1-
Appendix A: BIOS POST Codes POST Code 5Ch 60h 62h 64h 66h 67h 68h 69h 6Ah 6Bh 6Ch 6Eh 70h 72h 76h 7Ch 7Dh 7Eh 80h 81h 82h 83h 84h 85h 86h 87h 88h 89h 8Ah 8Bh 8Ch 8Fh 90h 91h 92h 93h 95h 96h 97h 98h Description Test RAM between 512 and 640 kB Test extended memory Test extended memory address lines Jump to UserPatch1 Configure advanced cache registers Initialize Multi Processor APIC Enable external and CPU caches Setup System Management Mode (SMM) area Display external L2 cache size Load custom defaults (op
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual POST Code 99h 9Ah 9Ch 9Dh 9Eh 9Fh A0h A2h A4h A8h AAh ACh AEh B0h B1h B2h B4h B5h B6h B7h B9h BAh BBh BCh BDh BEh BFh C0h C1h C2h C3h C4h C5h C6h C7h C8h C9h CAh CBh CCh Description Check for SMART Drive (optional) Shadow option ROMs Set up Power Management Initialize security engine (optional) Enable hardware interrupts Determine number of ATA and SCSI drives Set time of day Check key lock Initialize typematic rate Erase F2 prompt Scan for F2
Appendix A: BIOS POST Codes POST Code CDh CEh D2h Description Re-map I/O and memory for PCMCIA Initialize digitizer and display message Unknown interrupt The following are for boot block in Flash ROM POST Code E0h E1h E2h E3h E4h E5h E6h E7h E8h E9h EAh EBh ECh EDh EEh EFh F0h F1h F2h F3h F4h F5h F6h F7h Description Initialize the chipset Initialize the bridge Initialize the CPU Initialize system timer Initialize system I/O Check force recovery boot Checksum BIOS ROM Go to BIOS Set Huge Segment Initiali
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual Notes A-6
Appendix B: Software Installation Appendix B Software Installation After all the hardware has been installed, you must first configure the Adaptec Embedded Serial ATA RAID Driver before you install the Windows operating system. The necessary drivers are all included on the Supermicro bootable CDs that came packaged with your motherboard. (For Adaptec's SCSI Host RAID Utility, please refer to the CDs that came with your motherboard.
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual 5. Tap the Esc key and scroll down to "Exit". Select "Save and Exit" from the "Exit" menu. Press the Enter key to save the changes and exit the BIOS. 6. Once you've exited the BIOS Utility, the system will re-boot. 7. During system startup, press the Ctrl and the A keys simultaneously to run the Adaptec RAID Configuration Utility when prompted by the message: "Press for Adaptec RAID Configuration Utility".
Appendix B: Software Installation Using the Adaptec RAID Configuration Utility (ARC) The Adaptec RAID Configuration Utility is an embedded BIOS Utility, including: *Array Configuration Utility: Use this utility when you want to create, configure and manage arrays. *Disk Utilities: Use this option to format or verify disks.
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual Managing Arrays Select this option to view array properties and delete arrays. The following sections describe the operations Of "Managing Arrays". To select this option, use the arrow keys and the Enter key to select Managing Arrays from the main menu (as shown below).
Appendix B: Software Installation Viewing Array Properties To view the properties of an existing array: 1. At the BIOS prompt, press Ctrl+A. 2. From the ARC menu, select Array Configuration Utility (ACU). 3. From the ACU menu, select Manage Arrays (as shown on the previous screen.) 4. From the List of Arrays dialog box, select the array you want to view and press Enter. The Array Properties dialog box appears, showing detailed information on the array.
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual Creating Arrays Before creating arrays, make sure the disks for the array are connected and installed in your system. Note that disks with no usable space, or disks that are un-initialized are shown in gray and cannot be used. See Initializing Disk Drives. To create an array 1. Turn on your computer and press Ctrl+A when prompted to access the ARC utility. 2.
Appendix B: Software Installation Assigning Array Properties Once you've create a new array, you are ready to assign properties to the array. Caution: Once the array is created and its properties are assigned, you cannot change the array properties using the ACU. You will need to use the Adaptec Storage Manager - Browser Edition. (Refer to Adaptec's User's Guide in the enclosed CD.) To assign properties to the new array 1.
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual 4. The item "Create RAID via" allows you to select between the different methods of creating RAID 0 and RAID 1. The following table gives examples of when each is appropriate.
Appendix B: Software Installation Notes 1. Before adding a new drive to an array, back up any data contained on the new drive. Otherwise, all data will be lost. 2. If you stop the build or clear process on a RAID 1 from ACU, you can restart it by pressing Ctrl+R. 3. A RAID 1 created using the Quick Init option may return some data miscompares if you later run a consistency check. This is normal and is not a cause for concern. 4. The ACU allows you to use drives of different sizes in a RAID.
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual Adding a Bootable Array 1. From the Main menu, select Manage Arrays. 2. From the list of arrays, select the array you want to make bootable and press Ctrl+B. 3. Enter Y to create a bootable array when the following message is displayed: "This will make all other existing bootable array non-bootable. Do you want to make this array bootable? (Yes/No):" A bootable array will then be created. An asterisk will appear next to the bootable array.
Appendix B: Software Installation Adding/Deleting Hotspares Note: In order to rebuild a RAID (RAID 0 or RAID 1), you need to add a new HDD as a hotspare. 1. Turn on your computer and press Ctrl+A as prompted to access the ARC Utility. 2. From the ARC menu, select Array Configuration Utility (ACU). 3. From the ACU menu, select Add/Delete Hotspares. 4. Use the up and down arrow keys to highlight and select the disk you want to designate as a hotspare, and press Insert, then press Enter. 5.
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual Initializing Disk Drives If an installed disk does not appear in the disk selection list for creating a new array or if it appears grayed out, you may have to initialize it before you can use it as part of an array. Drives attached to the controller must be initialized before they can be used in an array. Caution: Initializing a disk overwrites the partition table on the disk and makes any data on the disk inaccessible.
Appendix B: Software Installation 5. Repeat Step 4 so that both drives to be initialized are selected (as shown on the following screen).
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual 6. Press Enter. 7. Read the warning message as shown on the screen below. 8. Make sure that you have selected the correct disk drives to initialize. If correct, type Y to continue. Rebuilding Arrays Note 1: Rebuilding applies to Fault Tolerant arrays (RAID 1) only. If an array build process (or initialization) is interrupted or critical with one member missing, you must perform a rebuild to optimized its functionality.
Appendix B: Software Installation Using the Disk Utilities The Disk Utilities enable you to format or verify the media of your Serial ATA hard disks. To access the disk utilities: 1. Turn on your computer and press Ctrl+A when prompted to access the ARC utility. 2. From the ARC menu, select Disk Utilities. 3. Select the desired disk and press Enter (as shown below.) You can choose from the following options 1.
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual To Exit Adaptec RAID Configuration Utility 1. Once you have completed RAID array configurations, press ESC to exit. The following screen will appear. 2. Press Yes to exit the Utility. For more information regarding the Adaptec RAID Utility, please refer to Adaptec's User's Guide in the CD included in your shipping package. You can also download a copy of Adaptec User's Guide from our web site at: www. supermicro.com.
Appendix B: Software Installation B-2 Installing Intel's ICH5R Driver by Adaptec and Windows OS 1. Insert Supermicro's bootable CD that came with the package into the CD Drive during the system reboot. The "Super Micro Driver Diskette Maker" screen will appear. 2. Choose "Intel ICH5R Driver by 3rd Party (Adaptec)" from the items listed and press Enter. 3. From the next screen displayed, choose the OS driver you want to install and press Enter. 4.
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual B-3 Installing Other Software Programs and Drivers Installing Other Drivers After you've installed the Windows Operating System, a screen (as shown in Figure B-1) will appear. You are now ready to install additional software programs and drivers. To install these software programs and drivers, click the icons to the right of these items. Figure B-1.
Appendix B: Software Installation Supero Doctor III The Supero Doctor III program is a web-based management tool that offers both remote and local management tools. The local management application is called SD III Client. The Supero Doctor III program included on the CDROM that came with your motherboard allows you to monitor the environment and operations of your system. Supero Doctor III displays crucial system information such as CPU temperature, system voltages and fan status.
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual Figure B-3. Supero Doctor III: Remote Control Display Note: SD III Software Revision 1.0 can be downloaded from our Web site at: ftp://ftp.supermicro.com/utility/Supero_Doctor_III/. You can also download the SDIII User's Guide at: http://www.supermicro.com/PRODUCT/Manuals/SDIII/UserGuide.pdf. For Linux, we recommend using Supero Doctor II.
Appendix C: System Specifications Appendix C System Specifications Processors Single or dual 604-pin Intel ® Xeon TM EM64T processors at a front side (system) bus speed of 800 MHz. Note: Please refer to our web site for a complete listing of supported processors: www.supermicro.
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual Expansion Slots 6014P-8/6014P-82: supports the use of one standard size 133 MHz PCI-X and one standard size 100 MHz PCI-X or two PCI-Express x8 add-on cards. 6014P-8R/6014P-82R: supports the use of one standard size 133 MHz PCI-X or one PCI-Express x8 add-on card. (See Section 5-6 for riser card details) Serverboard: 6014P-8/6014P-8R Model: X6DHP-8G (Extended ATX) Dimensions (both): 9.8" x 16.
Appendix C: System Specifications PFC Power Supply (ratings apply to each module) (SC814+S-R560: two power supply modules, SC814+S-560: one power supply module) Rated Output Power: 560W (Model# SP562-IR, Part# PWS-0057) Rated Output Voltages: +3.
SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual Notes C-4
