C7Z87-OCE USER’S MANUAL Revision 1.
The information in this User’s Manual has been carefully reviewed and is believed to be accurate. The vendor assumes no responsibility for any inaccuracies that may be contained in this document, makes no commitment to update or to keep current the information in this manual, or to notify any person or organization of the updates. Please Note: For the most up-to-date version of this manual, please see our web site at www.supermicro.com. Super Micro Computer, Inc.
Preface Preface This manual is written for system integrators, PC technicians and knowledgeable PC users. It provides information for the installation and use of the C7Z87-OCE motherboard. About This Motherboard The C7Z87-OCE supports a single 4th Generation Intel® Core™ i7/i5/i3 DT processor in an LGA 1150 (H3) socket. With the Intel® Z87 Express chipset built in, the C7Z87-OCE motherboard offers substantial system performance and storage capability for overclocking platforms in a sleek package.
C7Z87-OCE User’s Manual Conventions Used in the Manual: Special attention should be given to the following symbols for proper installation and to prevent damage done to the components or injury to yourself: Warning: Critical information to prevent damage to the components or injury to yourself. Important: Important information given to ensure proper system installation or to relay safety precautions.
Contacting Supermicro Contacting Supermicro Headquarters Address: Super Micro Computer, Inc. 980 Rock Ave. San Jose, CA 95131 U.S.A. Tel: +1 (408) 503-8000 Fax: +1 (408) 503-8008 Email: marketing@supermicro.com (General Information) support@supermicro.com (Technical Support) Web Site: www.supermicro.com Europe Address: Super Micro Computer B.V. Het Sterrenbeeld 28, 5215 ML 's-Hertogenbosch, The Netherlands Tel: +31 (0) 73-6400390 Fax: +31 (0) 73-6416525 Email: sales@supermicro.
C7Z87-OCE User’s Manual Table of Contents Preface Chapter 1 Introduction 1-1 Overview.......................................................................................................... 1-1 1-2 Chipset Overview ............................................................................................ 1-9 1-3 Special Features............................................................................................ 1-10 1-4 PC Health Monitoring.............................................
Table of Contents VGA Port................................................................................................... 2-19 DVI Port..................................................................................................... 2-19 Thunderbolt Interface................................................................................ 2-20 CMOS Reset/Clear.................................................................................... 2-20 Front Control Panel..................................
C7Z87-OCE User’s Manual 2-9 Onboard Indicators......................................................................................... 2-38 LAN 1/LAN 2 LEDs................................................................................... 2-38 Onboard Power LED (LED1) ................................................................... 2-38 Status Display (LED3,LED2) .................................................................... 2-39 2-10 SATA Connections........................................
Chapter 1: Introduction Chapter 1 Introduction 1-1 Overview Checklist Congratulations on purchasing your computer motherboard from an acknowledged leader in the industry. Supermicro boards are designed with the utmost attention to detail to provide you with the highest standards in quality and performance. Please check that the following items have all been included with your motherboard. If anything listed here is damaged or missing, contact your retailer.
C7Z87-OCE User’s Manual C7Z87-OCE Motherboard Image Note: All graphics shown in this manual were based upon the latest PCB Revision available at the time of publishing of the manual. The motherboard you've received may or may not look exactly the same as the graphics shown in this manual.
Chapter 1: Introduction C7Z87-OCE Motherboard Layout CLEAR CMOS SWITCH THUNDERBOLT AUDIO FP JSPDIF_OUT FAN5 JPAC1:AUDIO 1-2:ENABLE 2-3:DISABLE PCIE5 JPCIE6 ENABLE 2-3 DISABLE 1 3 JPL2 13 FOR HOME OR OFFICE USE ALWAYS POPULATE BLUE SOCKET FIRST UNB NON-ECC DDR3 DIMM REQUIRED 1 3 JSTBY1 JBT1 JPME2: 1-2:NORMAL 2-3:ME MANUFACTURING MODE 3 7 + 1 USB6/7 JPUSB2 10 2 JPME2 JBR1 USB 2/3 USB 2/3(3.
C7Z87-OCE User’s Manual C7Z87-OCE Quick Reference CLEAR CMOS SWITCH THUNDERBOLT AUDIO FP JSPDIF_OUT FAN5 JPAC1:AUDIO 1-2:ENABLE 2-3:DISABLE PCIE5 JPCIE6 ENABLE 2-3 DISABLE 1 3 JPL2 13 FOR HOME OR OFFICE USE ALWAYS POPULATE BLUE SOCKET FIRST UNB NON-ECC DDR3 DIMM REQUIRED 1 3 JSTBY1 JBT1 JPME2: 1-2:NORMAL 2-3:ME MANUFACTURING MODE BATTERY 7 3 7 + 1 USB6/7 JPUSB2 10 2 1 JPME2 JBR1 USB 2/3 USB 2/3(3.
Chapter 1: Introduction Connectors and Switches Connector Description I/O Back Panel See page 2-16 for details Audio FP Front Panel Audio Header Battery Onboard Battery COM1 COM1 Port Header Fan 1,2,3,4,5 System/CPU Fan Headers (Fan1: CPU Fan) JD1 Speaker/buzzer (Pins 1-2: Buzzer, Pins 1~4: External Speaker) JF1 Front Panel Control Header JL1 Chassis Intrusion Header JL2 Reserved JLED1 Power LED Indicator Header JPW1 24-pin ATX Main Power Connector (Required) JPW2 +12V 4-pin CPU pow
C7Z87-OCE User’s Manual Motherboard Features CPU Single 4th Generation Intel® Core™ i7/i5/i3 DT processor in an LGA1150 socket. Memory Four (4) SDRAM slots support up to 32 GB of DDR3 Unbuffered, Non-ECC 1600/1333/1066 MHz memory Single-channel memory DIMM sizes UDIMM 1 GB, 2 GB, 4GB, and 8GB Chipset Intel® Z87 Express Expansion Slots Three (3) PCI Express 2.0 x1 (in x4) slots One (1) PCI Express 3.0 x16/x8/x4 (in x16) slot* One (1) PCI Express 3.0 x8/x4 (in x16) slot* One (1) PCI Express 3.
Chapter 1: Introduction Audio One (1) High Definition Audio 7.1 channel connector supported by Realtek ALC1150 on the back panel One (1) Front Panel Audio Header One (1) SPDIF In/Out on the rear side of the chassis Super I/O Nuvoton NCT6776D BIOS 128 Mb AMI BIOS® SPI Flash BIOS Play and Plug (PnP0, DMI 2.3, PCI 2.3, ACPI 1.0/2.0/3.0, USB Keyboard and SMBIOS 2.
C7Z87-OCE User’s Manual C7Z87-OCE Block Diagram RoHS 6/6 P19 PCIe x16 SLOT #6 PCIe x8(in x16) SLOT #4 or PCIe x4(in x16) SLOT #4 PCIe3.0_x4 8.0GT/s 1 2 TI Switch HD3SS3415 P19 PCIe3.0_x4 8.0GT/s SVID VRM 12.5 8.0GT/s INTEL LGA1150 PCIe3.0_x8 8.0GT/s PCIe3.0_x4 8.0GT/s P20 PCIe3.0_x8 or PCIe x8(in x16) SLOT #6 P20 1 2 3 4 TI Switch HD3SS3415 DDR3 (CHA) Haswell - DT PCIe3.0_x8 (Socket-H3) 8.0GT/s 1600/1333/1066MHz VRD12.5 DDR3 (CHB) 1600/1333/1066MHz PCIe3.0_x4 8.
Chapter 1: Introduction 1-2 Chipset Overview The C7Z87-OCE motherboard supports a single 4th Generation Intel® Core i7/i5/i3 DT processor in the LGA 1150 Socket. Built upon the functionality and the capability of the Z87 Express chipset, the motherboard provides substantial enhancement to system performance, including overclocking capability.
C7Z87-OCE User’s Manual 1-3 Special Features Recovery from AC Power Loss Basic I/O System (BIOS) provides a setting for you to determine how the system will respond when AC power is lost and then restored to the system. You can choose for the system to remain powered off, (in which case you must press the power switch to turn it back on), or for it to automatically return to a power-on state. See the Advanced BIOS Setup section to change this setting. The default setting is Last State.
Chapter 1: Introduction is used to notify the user of certain system events. For example, you can also configure SuperDoctor to provide you with warnings when the system temperature, CPU temperatures, voltages and fan speeds go beyond predefined thresholds. 1-5 ACPI Features ACPI stands for Advanced Configuration and Power Interface.
C7Z87-OCE User’s Manual information, please refer to the web site at http://www.ssiforum.org/). Additionally, in areas where noisy power transmission is present, you may choose to install a line filter to shield the computer from noise. It is recommended that you also install a power surge protector to help avoid problems caused by power surges. 1-7 Super I/O The Super I/O supports two high-speed, 16550 compatible serial communication ports (UARTs).
Chapter 2: Installation Chapter 2 Installation 2-1 Standardized Warning Statements The following statements are industry-standard warnings, provided to warn the user of situations which have the potential for bodily injury. Should you have questions or experience difficulty, contact Supermicro's Technical Support department for assistance. Only certified technicians should attempt to install or configure components.
C7Z87-OCE User’s Manual Attention Danger d'explosion si la pile n'est pas remplacée correctement. Ne la remplacer que par une pile de type semblable ou équivalent, recommandée par le fabricant. Jeter les piles usagées conformément aux instructions du fabricant. ¡Advertencia! Existe peligro de explosión si la batería se reemplaza de manera incorrecta. Reemplazar la batería exclusivamente con el mismo tipo o el equivalente recomendado por el fabricante.
Chapter 2: Installation Product Disposal Warning! Ultimate disposal of this product should be handled according to all national laws and regulations. 製品の廃棄 この製品を廃棄処分する場合、国の関係する全ての法律・条例に従い処理する必要が あります。 警告 本产品的废弃处理应根据所有国家的法律和规章进行。 警告 本產品的廢棄處理應根據所有國家的法律和規章進行。 Warnung Die Entsorgung dieses Produkts sollte gemäß allen Bestimmungen und Gesetzen des Landes erfolgen. ¡Advertencia! Al deshacerse por completo de este producto debe seguir todas las leyes y reglamentos nacionales.
C7Z87-OCE User’s Manual عند التخلص النهائي من هذا المنتج ينبغي التعامل معه وفقا لجميع القىانين واللىائح الىطنية 경고! 이 제품은 해당 국가의 관련 법규 및 규정에 따라 폐기되어야 합니다. Waarschuwing De uiteindelijke verwijdering van dit product dient te geschieden in overeenstemming met alle nationale wetten en reglementen. 2-2 Static-Sensitive Devices Electrostatic-Discharge (ESD) can damage electronic components. To avoid damaging your system board, it is important to handle it very carefully.
Chapter 2: Installation 2-3 Processor and Heatsink Installation Warning: When handling the processor package, avoid placing direct pressure on the label area of the fan. Important: Always connect the power cord last, and always remove it before adding, removing or changing any hardware components. Make sure that you install the processor into the CPU socket before you install the CPU heatsink. If you buy a CPU separately, make sure that you use an Intel-certified multi-directional heatsink only.
C7Z87-OCE User’s Manual 2. Gently lift the load lever to open the load plate. Remove the plastic cap. 3. Use your thumb and your index finger to hold the CPU at the North center edge and the South center edge of the CPU. North Center Edge South Center Edge 4. Align the CPU key that is the semi-circle cutouts against the socket keys. Once it is aligned, carefully lower the CPU straight down into the socket. (Do not drop the CPU on the socket. Do not move the CPU horizontally or vertically.
Chapter 2: Installation 5. Do not rub the CPU against the surface or against any pins of the socket to avoid damaging the CPU or the socket.) 6. With the CPU inside the socket, inspect the four corners of the CPU to make sure that the CPU is properly installed. 7. Use your thumb to gently push the load lever down to the lever lock. CPU properly installed Load lever locked into place Warning: You can only install the CPU inside the socket only in one direction.
C7Z87-OCE User’s Manual Installing an Active CPU Heatsink with Fan 1. Locate the CPU Fan power connector on the motherboard. (Refer to the layout on the right for the CPU Fan location.) 2. Position the heatsink so that the heatsink fan wires are closest to the CPU fan power connector and are not interfered with other components. Thermal Grease 3. Inspect the CPU Fan wires to make sure that the wires are routed through the bottom of the heatsink. 4.
Chapter 2: Installation 7. Align the four heatsink fasteners with the mounting holes on the motherboard. Gently push the pairs of diagonal fasteners (#1 & #2, and #3 & #4) into the mounting holes until you hear a click. Also, make sure to orient each fastener so that the narrow end of the groove is pointing outward. 8. Repeat Step 7 to insert all four heatsink fasteners into the mounting holes. 9.
C7Z87-OCE User’s Manual Removing the Heatsink Warning: We do not recommend that the CPU or the heatsink be removed. However, if you do need to remove the heatsink, please follow the instructions below to remove the heatsink and to prevent damage done to the CPU or other components. Active Heatsink Removal 1. Unplug the power cord from the power supply. Unplug the PWR cord 2. Disconnect the heatsink fan wires from the CPU fan header. 3.
Chapter 2: Installation 2-4 Installing DDR3 Memory Note: Check the Supermicro website for recommended memory modules. CAUTION Exercise extreme care when installing or removing DIMM modules to prevent any possible damage.
C7Z87-OCE User’s Manual Memory Support The C7Z87-OCE supports up to 32GB of Unbuffered (UDIMM) DDR3 Non-ECC 1600/1333/1066 MHz in 4 memory slots. Populating these DIMM modules with a Towards the CPU P1-DIMMA1 P1-DIMMA2 (Blue Slot) P1-DIMMB1 P1-DIMMB2 (Blue Slot) Towards the edge of the motherboard pair of memory modules of the same type and same size will result in interleaved memory, which will improve memory performance.
Chapter 2: Installation • For Microsoft Windows users: Microsoft implemented a design change in the Windows XP with Service Pack 2 (SP2) and Windows Vista. This change is specific to the behavior of Physical Address Extension (PAE) mode which improves driver compatibility. For more information, please read the following article at Microsoft’s Knowledge Base website at: http://support.microsoft. com/kb/888137.
C7Z87-OCE User’s Manual 2-5 Motherboard Installation All motherboards have standard mounting holes to fit different types of chassis. Make sure that the locations of all the mounting holes for both motherboard and chassis match. Although a chassis may have both plastic and metal mounting fasteners, metal ones are highly recommended because they ground the motherboard to the chassis. Make sure that the metal standoffs click in or are screwed in tightly.
Chapter 2: Installation Installing the Motherboard 1. Install the I/O shield into the back of the chassis. 2. Locate the mounting holes on the motherboard. (See the previous page.) 3. Locate the matching mounting holes on the chassis. Align the mounting holes on the motherboard against the mounting holes on the chassis. 4. Install standoffs in the chassis as needed. 5. Install the motherboard into the chassis carefully to avoid damaging other motherboard components. 6.
C7Z87-OCE User’s Manual 2-6 Connectors/IO Ports The I/O ports are color coded in conformance with the PC 99 specification. See the figure below for the colors and locations of the various I/O ports. Backplane I/O Panel A B C D E F G H I K J M L N O P Q R S Backplane I/O Panel A. USB 2.0 Port 0 H. Gb LAN Port 1 N. Center/LFE Out B. USB 2.0 Port 1 I. USB 3.0 Port 6 O. Surround Out C. HDMI Port J. USB 3.0 Port 7 P. S/PDIF Out D. VGA Port K. Gb LAN Port 2 Q. Line In E.
Chapter 2: Installation Universal Serial Bus (USB) Two Universal Serial Bus 2.0 ports (0/1) and four USB 3.0 ports (4/5,6/7) are located on the I/O back panel. In addition, two USB 2.0 headers (four ports: 4/5, 6/7), and two USB 3.0 headers (four ports: 0/1, 2/3) are also located on the motherboard to provide front chassis access using USB cables (not included). See the tables below for pin definitions. Front Panel USB (2.0) #4/5, 6/7 Pin Definitions Pin # Definition Pin # Back Panel USB (2.
C7Z87-OCE User’s Manual Ethernet Ports LAN Ports Pin Definition Two Gigabit Ethernet ports (LAN1/ LAN2) are located next to the Pin# Definition HD Audio Connector on the I/O Backpanel to provide network connections. These ports accept RJ45 type cables. Note: Please refer to the LED Indicator Section for LAN LED information.
Chapter 2: Installation HDMI Port One HDMI (High-Definition Multimedia Interface) is located next to the VGA port on the I/O backpanel. This connector is used to display both high definition video and digital sound through an HDMI capable display, using a single HDMI cable (not included). VGA Port A VGA port is located next to the USB ports 0/1 on the I/O backpanel. Use this port to connect to a compatible VGA display. DVI Port A DVI port is located just under the VGA port on the I/O backpanel.
C7Z87-OCE User’s Manual Thunderbolt Interface This motherboard supports one Thunderbolt interface on the backpanel. A Thunderbolt interface is a hardware interface that allows peripherals to be connected to the motherboard at transfer speeds of up to 10Gbit/s. This port combines a PCIe and a DisplayPort into one serial signal. A. Thunderbolt Interface CMOS Reset/Clear B.
Chapter 2: Installation Front Control Panel JF1 contains header pins for various buttons and indicators that are normally located on a control panel at the front of the chassis. These connectors are designed specifically for use with Supermicro chassis. See the figure below for the descriptions of the front control panel buttons and LED indicators. Refer to the following section for descriptions and pin definitions.
C7Z87-OCE User’s Manual Front Control Panel Pin Definitions Power LED Power LED Pin Definitions (JF1) The Power LED connection is located on pins 15 and 16 of JF1. Refer to the table on the right for pin definitions. Pin# Definition 15 +5V 16 Ground HDD LED HDD LED Pin Definitions (JF1) The HDD LED connection is located on pins 13 and 14 of JF1. Attach a cable here to indicate the status of HDD-related activities, including IDE, SATA activities. See the table on the right for pin definitions.
Chapter 2: Installation Reset Button Reset Button Pin Definitions (JF1) The Reset Button connection is located on pins 3 and 4 of JF1. Attach it to a hardware reset switch on the computer case to reset the system. Refer to the table on the right for pin definitions. Pin# Definition 3 Reset 4 Ground Power Button Power Button Pin Definitions (JF1) The Power Button connection is located on pins1 and 2 of JF1. Momentarily contacting both pins will power on/off the system.
C7Z87-OCE User’s Manual 2-7 Connecting Cables This section provides brief descriptions and pin-out definitions for onboard headers and connectors. Be sure to use the correct cable for each header or connector. For information on Backpanel USB and Front Panel USB ports, refer to Page 2-17. For Front Panel Audio, please refer to Page 2-19.
Chapter 2: Installation Fan Headers (Fan 1 ~ Fan 5) Fan Header Pin Definitions The C7Z87-OCE has five fan headers (Fan 1~Fan 5). These fans are 4-pin fan headers. Although pins 1-3 of the fan headers are backward compatible with the traditional 3-pin fans, we recommend the use 4-pin fans to take advantage of the fan speed control via IPMI interface. This allows the fan speeds to be automatically adjusted based on the motherboard temperature. Refer to the table on the right for pin definitions.
C7Z87-OCE User’s Manual Internal Buzzer (SP1) Internal Buzzer Pin Definition The Internal Buzzer (SP1) can be used to provide audible indications for Pin# various beep codes. See the table on the right for pin definitions. Pin 1 Pos. (+) Beep In Pin 2 Neg. (-) Alarm Speaker Speaker (JD1) Definitions Speaker Connector Pin Definitions On the JD1 header, Pins 3~4 are used for internal speaker. Close pins 3~4 with a cap to use the onboard speaker.
Chapter 2: Installation Onboard Power LED (JLED1) Onboard PWR LED Pin Definitions An onboard Power LED header is located at JLED1. This Power LED header is connected to Front Control Panel located at JF1 to indicate the status of system power. See the table on the right for pin definitions. Pin# Definition 1 VCC 2 No Connection 3 Connection to PWR LED in JF1 Serial/COM Ports Pin Definitions Serial Port (COM1) There is one serial (COM) port header on the motherboard.
C7Z87-OCE User’s Manual DOM PWR Connector (JSD1) The Disk-On-Module (DOM) power connector, located at JSD1, provides 5V (Gen1/Gen) power to a solid state DOM storage device connected to one of the SATA ports. See the table on the right for pin definitions. DOM PWR Pin Definitions Pin# Definition 1 5V 2 Ground 3 Ground SPDIF OUT (JSPDIF_OUT) The SPDIF Out (JSPDIF_OUT) is used for digital audio output. You will also need the appropriate cable to use these features.
Chapter 2: Installation Standby Power Header Standby Power Pin Definitions The Standby Power header is located at STBY1 on the motherboard. See Pin# Definition the table on the right for pin definitions. 1 +5V Standby 2 Ground 3 Wake-up Chassis LED If this motherboard will be mounted on a Supermicro chassis, this header can be used to attach the motherboard to control the chassis' LED readout. A. STBY PWR B.
C7Z87-OCE User’s Manual TPM Header/Port 80 Header A Trusted Platform Module/Port 80 header is located at JTPM1 to provide TPM support and Port 80 connection. Use this header to enhance system performance and data security. See the table on the right for pin definitions. TPM/Port 80 Header Pin Definitions Pin # Definition Pin # LCLK 2 GND 3 LFRAME# 4 <(KEY)> 5 LRESET# 6 +5V (X) 7 LAD 3 8 LAD 2 9 +3.
Chapter 2: Installation Front Panel Audio Header (AUDIO FP) A 10-pin Audio header is supported on the motherboard. This header allows you to connect the motherboard to a front panel audio control panet, if needed. Connect an audio cable to the audio header to use this feature (not supplied). See the table at right for pin definitions for the header.
C7Z87-OCE User’s Manual 2-8 Jumper Settings Explanation of Jumpers To modify the operation of the motherboard, jumpers can be used to choose between optional settings. Jumpers create shorts between two pins to change the function of the connector. Pin 1 is identified with a square solder pad on the printed circuit board. Note: On two-pin jumpers, "Closed" means the jumper is on, and "Open" means the jumper is off the pins.
Chapter 2: Installation CMOS Clear (JBT1) JBT1 is used to clear the saved system setup configuration stored in the CMOS chip. To clear the contents of the CMOS, completely shut down the system, remove the AC power cord and then short JBT1 with a jumper. Remove the jumper before powering on the system again. This will erase all user settings and revert everything to their factory-set defaults.
C7Z87-OCE User’s Manual Audio Enable (JPAC1) JPAC1 allows you to enable or disable the onboard audio support. The default position is on pins 1 and 2 to enable onboard audio connections. See the table on the right for jumper settings. Audio Enable/Disable Jumper Settings Both Jumpers Definition Pins 1-2 Enabled Pins 2-3 Disabled Watch Dog Jumper Settings Watch Dog Enable/Disable Watch Dog (JWD1) is a system monitor that can reboot the system when a software application hangs.
Chapter 2: Installation USB Wake-Up (JPUSB 1/2) Use jumper JPUSB1 to activate the "wakeup" function of the USB ports by pressing a key on a USB keyboard or clicking the USB mouse connected. This jumper is used together with a USB Wake-Up feature in the BIOS. Enable this jumper and the USB support in the BIOS to wake up your system via USB devices.
C7Z87-OCE User’s Manual Management Engine (ME) Recovery (JPME1) Use Jumper JPME1 to select ME frmware Recovery mode, which will limit resource allocation for essential systemoperation only in order to maintain normal power operation and management. In the single operation mode, online upgrade will be available via Recovery mode. See the table on the right for jumper settings.
Chapter 2: Installation BIOS Recovery (JBR1) The BIOS Recovery (JBR1) is used to enable or disable the BIOS Recovery feature of the motherboard. Install the jumper on pins 2-3 to begin the recovery process. See Appendix D for related information. Power Button In addition to the soft power switch provided in JF1, your motherboard is equipped with a 'soft' power button on the motherboard. This switch works the same way as the soft power switch on JF1.
C7Z87-OCE User’s Manual 2-9 Onboard Indicators LAN1 LAN 1/LAN 2 LEDs LAN2 Link LED Two LAN ports (LAN 1/LAN 2) are located on the I/O backplane of the motherboard. Each Ethernet LAN port has two LEDs. The yellow LED indicates activity, while the Link LED may be green, amber, or off to indicate the speed of the connections. See the tables at right for more information.
Chapter 2: Installation Status Display (LED3,LED2) LED3 and LED2 are alpha-numeric displays that will display a status or POST code when the motherboard is powered on. Please download the following AMI publication for a complete list of POST codes: http://www.ami.com/support/doc/ami_aptio_4.x_status_codes_pub.pdf A.
C7Z87-OCE User’s Manual 2-10 SATA Connections SATA Connections (I-SATA0~I-SATA5) Eight Serial ATA (SATA) 3.0 connectors (I-SATA 0~5, A-SATA 0/1) are supported on the board. The I-SATA 3.0 ports are supported by the Intel Z87 PCH chip (supports RAID 0,1,5,10) while the A-SATA 3.0 ports are provided by the ASMedia SATA Controller. These Serial Link connections provide faster data transmission than legacy Parallel ATA. See the table on the right for pin definitions. SATA 2.0/3.
Chapter 3: Troubleshooting Chapter 3 Troubleshooting 3-1 Troubleshooting Procedures Use the following procedures to troubleshoot your system. If you have followed all of the procedures below and still need assistance, refer to the ‘Technical Support Procedures’ and/or ‘Returning Merchandise for Service’ section(s) in this chapter. Always disconnect the AC power cord before adding, changing or installing any hardware components. Before Power On 1. Make sure that the Standby PWR LED is not on.
C7Z87-OCE User’s Manual No Video 1. If the power is on, but you have no video--in this case, you will need to remove all the add-on cards and cables first. 2. Use the speaker to determine if any beep codes exist. (Refer to Appendix A for details on beep codes.) 3. Remove all memory modules and turn on the system. (If the alarm is on, check the specifications of memory modules, reset the memory or try a different one.) Memory Errors 1.
Chapter 3: Troubleshooting 3-2 Technical Support Procedures Before contacting Technical Support, please make sure that you have followed all the steps listed below. Also, Note that as a motherboard manufacturer, Supermicro does not sell directly to end users, so it is best to first check with your distributor or reseller for troubleshooting services. They should know of any possible problem(s) with the specific system configuration that was sold to you. 1.
C7Z87-OCE User’s Manual 3-3 Frequently Asked Questions Question: What type of memory does my motherboard support? Answer: The C7Z87-OCE supports up to 32GB of unbuffered Non-ECC DDR3 SDRAM (1.5V, 1600/1333/1066 MHz). See Section 2-4 for details on installing memory. Question: How do I update my BIOS? Answer: We do NOT recommend that you upgrade your BIOS if you are not experiencing any problems with your system. Updated BIOS files are located on our website at http://www.supermicro.com/support/bios/.
Chapter 3: Troubleshooting Important: The SPI BIOS chip installed on this motherboard is not removable. To repair or replace a damaged BIOS chip, please send your motherboard to RMA at Supermicro for service. Question: I think my BIOS is corrupted. How can I recover my BIOS? Answer: Please see Appendix C-BIOS Recovery for detailed instructions. Question: Why do I get an error message “IASTOR.
C7Z87-OCE User’s Manual regulations set up by your local hazardous waste management agency to dispose of your used battery properly. Battery Installation 1. To install an onboard battery, follow the steps 1 & 2 above and continue below: 2. Identify the battery's polarity. The positive (+) side should be facing up. 3. Insert the battery into the battery holder and push it down until you hear a click to ensure that the battery is securely locked.
Chapter 4: AMI BIOS Chapter 4 BIOS 4-1 Introduction This chapter describes the AMI BIOS Setup Utility for the C7Z87-OCE. The ROM BIOS is stored in a Flash EEPROM and can be easily updated. This chapter describes the basic navigation of the AMI BIOS Setup Utility setup screens. Note: For AMI BIOS Recovery, please refer to the UEFI BIOS Recovery Instructions in Appendix C. Starting BIOS Setup Utility To enter the AMI BIOS Setup Utility screens, press the key while the system is booting up.
C7Z87-OCE User’s Manual How to Start the Setup Utility Normally, the only visible Power-On Self-Test (POST) routine is the memory test. As the memory is being tested, press the key to enter the main menu of the AMI BIOS Setup Utility. From the main menu, you can access the other setup screens. An AMI BIOS identification string is displayed at the left bottom corner of the screen, below the copyright message. Warning! Do not upgrade the BIOS unless your system has a BIOS-related issue.
Chapter 4: AMI BIOS System Date/System Time Use this option to change the system date and time. Highlight System Date or System Time using the arrow keys. Enter new values using the keyboard. Press the key or the arrow keys to move between fields. The date must be entered in Day MM/DD/YYYY format. The time is entered in HH:MM:SS format. Note: The time is in the 24-hour format. For example, 5:30 P.M. appears as 17:30:00.
C7Z87-OCE User’s Manual 4-3 Advanced Setup Configurations Use the arrow keys to select Advanced Setup and press to access the submenu items: Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Chapter 4: AMI BIOS Wait For 'F1' If Error Select Enabled to force the system to wait until the 'F1' key is pressed if an error occurs. The options are Disabled and Enabled. Interrupt 19 Capture Interrupt 19 is the software interrupt that handles the boot disk function. When this item is set to Enabled, the BIOS ROM of the host adaptors will "capture" Interrupt 19 at bootup and allow the drives that are attached to these host adaptors to function as bootable disks.
C7Z87-OCE User’s Manual CPU Configuration The following CPU information will be displayed: • Type of CPU • CPU Signature • CPU Stepping • Microcode Patch • Max (Maximum) CPU Speed • Min (Minimum) CPU Speed • CPU Speed • Processor Cores • Intel HT(Hyper-Threading) Technology • Intel VT-x (Virtualization) Technology • Intel SMX (Trusted Execution) Technology • 64-bit • EIST Technology • CPU C3 State • CPU C6 State • CPU C7 State • L1 Data Cache • L1 Code Cache • L2 Cache • L3 Cache 4-6
Chapter 4: AMI BIOS Clock Spread Spectrum If this feature is set to Enabled, the BIOS will monitor the level of electromagnetic interference caused by the components and will attempt to reduce the interference whenever needed. The options are Enabled and Disabled. Hyper-threading Select Enabled to support Intel Hyper-threading Technology to enhance CPU performance. The options are Enabled and Disabled. Active Processor Cores This feature determines how many CPU cores will be activated for each CPU.
C7Z87-OCE User’s Manual Adjacent Cache Line Prefetch (Available when supported by the CPU) Select Enabled for the CPU to prefetch both cache lines for 128 bytes as comprised. Select Disabled for the CPU to prefetch both cache lines for 64 bytes. The options are Disabled and Enabled. Note: If there is any change to this setting, you will need to power off and reboot the system for the change to take effect. Please refer to Intel’s web site for detailed information.
Chapter 4: AMI BIOS CPU Power Limit3 Use this feature to set the power limit for CPU3. Use the number keys on your keyboard to enter the value. Enter 0 to use the manufacturer's default setting. CPU Power Limit3 Time This item allows the user to determine how long CPU3 should operate at the power limit set by the user for the item above. Use the number keys on your keyboard to enter the value. Enter 0 to use the manufacturer's default setting.
C7Z87-OCE User’s Manual 3-Core Ratio Limit This increases (multiplies) 3 clock speeds in the CPU core in relation to the bus speed when three CPU cores are active. Press "+" or "-" on your keyboard to change the value. Enter 0 to use the manufacturer's default setting. 4-Core Ratio Limit This increases (multiplies) 4 clock speeds in the CPU core in relation to the bus speed when four CPU cores are active. Press "+" or "-" on your keyboard to change the value.
Chapter 4: AMI BIOS C6 Latency (Available when "CPU C States" is set to Enabled) Select Short to set a short delay time(period) during which the BIOS reports CPU C6 State (ACPI C3) to the operating system. Select Long to set a long delay time(period) during which the BIOS reports CPU C6 State (ACPI C3) to the operating system. The options are Short and Long.
C7Z87-OCE User’s Manual ACPI T State Select Enabled to support Advanced Configuration and Power Interface (ACPI) Throttling States (T State), which will lower the power consumption level for the system as to the power consumption level set for CPU Performance State 1 to achieve power efficiency. The options are Enabled and Disabled. Chipset Configuration WARNING: Setting the wrong values in the following sections may cause the system to malfunction.
Chapter 4: AMI BIOS Primary Display Use this feature to select the graphics device to be used as the primary display. You can select from a device installed on the CPU IGFX, CPU SLOT, or PCH SLOT. The options are Auto, CPU IGFX, CPU SLOT, and PCH SLOT. CPU Slot (Available when Primary Display is set to Auto) Use this item to select the graphics device installed in an expansion slot supported by the CPU to be used as the primary display. The options are Auto, CPU SLOT4 PCI-E 3.
C7Z87-OCE User’s Manual Gfx (Graphics) Low Power Mode Select Enabled to use the low power mode for internal graphics devices installed in a small form factor (SFF) computer. The options are Enabled and Disabled. PCI-E Configuration This item displays the information of the (graphics) device installed on a PCI-E slot. CPU SLOT6 PCI-E 3.0 X16 CPU SLOT6 PCI-E 3.0 X16 - Gen X This feature allows the user to select PCI-E support for the device installed on Slot6.
Chapter 4: AMI BIOS CPU SLOT6 PCI-E 3.0 X16 - ASPM, CPU SLOT4 PCI-E 3.0 X8(IN X16) - ASPM, CPU SLOT2 PCI-E 3.0 X4 (IN X16)- ASPM Use this feature to set the ASPM (Active State Power Management) level for the graphics device installed on a PCI-E or PCI slot specified by the user. The options are Disabled, ASPM L0s, ASPM L1, ASPM L0sL1, and Auto. DMI Link ASPM Control Use this feature to set the ASPM (Active State Power Management) state on the SA (System Agent) side of the DMI Link.
C7Z87-OCE User’s Manual • Minimum Delay Time • CAS to RAS (tRCDmin) • Row Precharge (tRPmin) • Active to Precharege (tRASmin) Max TOLUD (Top of Low Usable DRAM) This feature sets the maximum TOLUD value, which specifies the "Top of Low Usable DRAM" memory space to be used by internal graphics devices, GTT Stolen Memory, and TSEG, respectively, if these devices are enabled. The options are Dynamic, 1 GB, 1.25 GB, 1.5 GB, 1.75 GB, 2 GB, 2.25 GB, 2.5 GB, 2.75 GB, 3 GB and 3.25 GB.
Chapter 4: AMI BIOS Legacy USB Support Select Enabled to support legacy USB devices. Select Auto to disable legacy support when legacy USB devices are not present. If Disable is selected, legacy USB devices will not be supported. The options are Enabled, Disabled and Auto. Port 60/64 Emulation This feature enables or disables I/O port 60h/64h emulation support. This should be enabled for complete USB keyboard legacy support for non-USB-aware operating systems. The options are Disabled and Enabled.
C7Z87-OCE User’s Manual SATA Configuration When this submenu is selected, the AMI BIOS automatically detects the presence of the SATA Devices and displays the following items: SATA Controllers This item Enables or Disables the built-in SATA controllers on the motherboard. The options are Enabled and Disabled. SATA Mode Selection This item selects the mode for the installed SATA drives. The options are IDE, AHCI and RAID.
Chapter 4: AMI BIOS If the item above - SATA Mode Select is set to IDE, the following items are displayed: Serial ATA Port 0~ Port 5 This item displays the information detected on the installed SATA drives on the particular SATA port.
C7Z87-OCE User’s Manual VGA Palette Snoop Select Enabled to support VGA palette register snooping which will allow the PCI cards that do not contain their own VGA color palette to examine the video cards palette and mimic it for proper color display. The options are Disabled and Enabled. PERR# Generation Select Enabled to allow a PCI device to generate a PERR number for a PCI Bus Signal Error Event. The options are Enabled and Disabled.
Chapter 4: AMI BIOS Network Stack Select Enabled to enable PXE (Preboot Execution Environment) or UEFI (Unified Extensible Firmware Interface) for network stack support. The options are Enabled and Disabled. Ipv4 PXE Support (Available when Network Stack is set to Enabled) Select Enabled to enable Ipv4 PXE (Preboot Execution Environment) for boot support. If this feature is set to Disabled, Ipv4 PXE boot option will not be supported. The options are Enabled and Disabled.
C7Z87-OCE User’s Manual TPM State Select Enabled to use TPM (Trusted Platform Module) settings for system data security. The options are Disabled and Enabled. Note: The system will reboot for the change on TPM State to take effect. Pending Operation Use this item to schedule a TPM-related operation to be performed by a security device for TPM support. The options are None, Enable Take Ownership, Disable Take Ownership, and TPM Clear.
Chapter 4: AMI BIOS Package Current Lock Select Enabled to lock the current CPU package values. The options are Enabled and Disabled. IA Core Current Max (1/8 Amp) This feature allows the user to set the maximum electric current value for the Intel CPU cores. The default setting is 760. Enhanced Intel SpeedStep Technology Select Enabled to enable Enhanced Intel SpeedStep Technology (EIST) support to allow the system to automatically adjust processor voltage and core frequency to enhance power efficiency.
C7Z87-OCE User’s Manual keyboard to enter the value. The default setting is dependent on the CPU installed. 2 Core Ratio Limit This increases (multiplies) 2 clock speeds in the CPU core in relation to the bus speed when two CPU cores are active. Use the number keys on your keyboard to enter the value. The default setting is dependent on the CPU installed. 3 Core Ratio Limit This increases (multiplies) 3 clock speeds in the CPU core in relation to the bus speed when three CPU cores are active.
Chapter 4: AMI BIOS North Bridge Configuration The following North Bridge Configuration submenu items will display: Memory Multiplier Configuration Performance Memory Profiles Use this feature to set Performance Memory Profiles which may cause impact on memory behavior due to different sizes of memory used in the system. Select Automatic to allow the BIOS to automatically set Performance Memory Profiles. Select Manual to manually configure Performance Profiles.
C7Z87-OCE User’s Manual tWR This option configures the Minimum Write Recovery Time. Enter a number between 1-38. The default is 12. tRFC This option selects the Minimum Refresh Recovery Delay Time. Enter a number between 1-9363. The default is 128. tWTR This option configures the Minimum Internal Write to Read Command Delay Time. Enter a number between 1-38. The default is 6. tRRD This option selects the Minimum Row Active To Row Active Delay Time. Enter a number between 1-38. The default is 5.
Chapter 4: AMI BIOS Memory Voltage Use this feature to select the Memory Voltage. The options are 1.35V, 1.40V, 1.45V, 1.50V, 1.55V, 1.60V, 1.65V, 1.70V, 1.75V, 1.80V, 1.85V, 1.90V, 1.95V and Auto. Intel Graphics Configuration Graphics Core Ratio Limit Use this feature to set graphics core ratio limit. The default setting is dependent on the type of CPU installed.
C7Z87-OCE User’s Manual RING Voltage Offset (mV) Use this feature to set to set the RING Voltage Offset value from -1000mV to 998mV. Enter 0 to use the manufacture default value. Offset Prefix Use this feature to set the Offset value as a positive (+) number or a negative (-) number. Press "+" or "-" on your keyboard to make a selection. The default setting is "+".
Chapter 4: AMI BIOS GT Voltage Offset (mV) Use this feature to set the GT Voltage Offset value between -1000mV and 998mV. Enter 0 to use the default setting. Offset Prefix Use this feature to set the GT Voltage Offset value as a positive (+) number or a negative (-) number. Press "+" or "-" on your keyboard to make a selection. The default setting is "+".
C7Z87-OCE User’s Manual Offset Prefix Use this feature to set the Offset value as a positive (+) number or a negative (-) number. Press "+" or "-" on your keyboard to make a selection. The default setting is "+". Overclocking Button Option The following Overclocking Button Option submenu items will display.
Chapter 4: AMI BIOS RING Voltage Offset (mV) Use this feature to set to set the RING Voltage Offset value from -1000mV to 998mV. Enter 0 to use the manufacture default value. Offset Prefix Use this feature to set the Offset value as a positive (+) number or a negative (-) number. Press "+" or "-" on your keyboard to make a selection. The default setting is "+". IOA Voltage Offset (mV) Use this feature to set the IOA Voltage Offset value between -1000mV and 998mV. Enter 0 to use the default setting.
C7Z87-OCE User’s Manual Memory Timing Configuration Memory Clock Multiplier This option selects the Memory Clock Multiplier. The options are 1.33 and 1.00. Memory Multiplier This option selects the Memory Multiplier value. The options are 8, 10, 12, 14, 16, 18, 20, 22, 24, 26 and 28. tCL This option configures the Cas Latency Range. Enter a number between 4-18. The default is 9. tRP This option selects the Ras Precharge Range. Enter a number between 1-38. The default is 11.
Chapter 4: AMI BIOS tRRD This option selects the Minimum Row Active To Row Active Delay Time. Enter a number between 1-38. The default is 5. tRTP This option configures the Internal Read to Precharge Command Delay Time. Enter a number between 1-38. The default is 6. tCWL Value This option selects the Minimum CAS Write Latency Time. Enter a numeric value. The default is 8. tREFI Value This option configures the Maximum tREFI Time (Average Periodic Refrech Interval). Enter a numeric value.
C7Z87-OCE User’s Manual Intel Graphics Configuration Graphics Core Ratio Limit This option allows the configuration of the Graphics Core Ratio limit. Please enter a numeric value. The default is 24. Case LED The following setting will enable the LED lamp that is mounted on the chassis to flash when Over-Clocking is enabled. The options are Enabled and Disabled.
Chapter 4: AMI BIOS Security Level This option selects the security level for the Intel Thunderbolt port(s) . The options are Legacy Mode, Unique ID, One Time Saved Key, and DP+++ only. Wake From Thunderbolt Devices This option enables the wake-up feature from Thunderbolt devices. The options are Disabled, and Enabled. Thunderbolt PCIe Cache-Line Size This option configures the cache-line size value to be configured on the Thunderbolt PCIe subtree. The options 0, 1, 2, 4, 8, 16, 32, 64, and 128.
C7Z87-OCE User’s Manual Device Settings This feature displays the base I/O port address and the Interrupt Request address of Serial Port 1. Change Port 1 Settings This option specifies the base I/O port address and the Interrupt Request address of Serial Port 1. Select Auto to let the BIOS automatically assign the base I/O and IRQ address.
Chapter 4: AMI BIOS H/W (Hardware) Monitor PC Health Status Fan Speed Control Mode This feature allows the user to decide how the system controls the speeds of the onboard fans. The CPU temperature and the fan speed are correlative. When the CPU on-die temperature increases, the fan speed will also increase for effective system cooling. Select "Full Speed" to allow the onboard fans to run at full speed (of 100% Pulse Width Modulation Duty Cycle) for maximum cooling.
C7Z87-OCE User’s Manual 4-4 Boot Settings Use this feature to configure Boot Settings: Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Chapter 4: AMI BIOS Delete Boot Option Use this feature to remove a pre-defined boot device from which the system will boot during startup. The settings are [any pre-defined boot device] Delete Driver Option Use this feature to remove a pre-defined driver from which the system will boot during startup.
C7Z87-OCE User’s Manual 4-5 Security Settings This menu allows the user to configure the following security settings for the system. Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc. Main Advanced Boot Security Exit Password Description Set Administrator Password. If ONLY the administrator’s password is set, then this only limits access to Setup and is only asked for when entering Setup.
Chapter 4: AMI BIOS 4-6 Save & Exit Select the Exit tab from the BIOS Setup Utility screen to enter the Exit BIOS Setup screen. Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc. Main Advanced Boot Security Exit Exit system setup after saving the changes.
C7Z87-OCE User’s Manual Save As User Defaults To set this feature, select Save as User Defaults from the Exit menu and press . This enables the user to save any changes to the BIOS setup for future use. Restore User Defaults To set this feature, select Restore User Defaults from the Exit menu and press . Use this feature to retrieve user-defined settings that were saved previously. Boot Override Listed on this section are other boot options for the system (i.e., Built-in EFI shell).
Appendix A: POST Error Beep Codes Appendix A BIOS Error Beep Codes During the POST (Power-On Self-Test) routines, which are performed each time the system is powered on, errors may occur. Non-fatal errors are those which, in most cases, allow the system to continue with bootup. The error messages normally appear on the screen. Fatal errors will not allow the system to continue to bootup. If a fatal error occurs, you should consult with your system manufacturer for possible repairs.
C7Z87-OCE User’s Manual Notes A-2
Appendix B: Software Installation Instructions Appendix B Software Installation Instructions B-1 Installing Drivers After you've installed the Windows Operating System, a screen as shown below will appear. You are ready to install software programs and drivers that have not yet been installed. To install these software programs and drivers, click the icons to the right of these items. (Note: To install the Windows Operating System, please refer to the instructions posted on our website at http://www.
C7Z87-OCE User’s Manual B-2 Configuring SuperDoctor® III The SuperDoctor III program is a Web-based management tool that supports remote management capability. It includes Remote and Local Management tools. The local management tool is called the SD III Client. The SuperDoctor III program included on the CDROM that came with your motherboard allows you to monitor the environment and operations of your system.
Appendix B: Software Installation Instructions SuperDoctor III Interface Display Screen-II (Remote Control) Note: The SuperDoctor III software and manual may be downloaded from our Website at: http://www.supermicro.com/products/accessories/software/SuperDoctorIII.cfm. For Linux, we still recommend that you use SuperDoctor II, this version is also available for download at the link above.
C7Z87-OCE User’s Manual Notes B-4
Appendix C: UEFI BIOS Recovery Appendix C UEFI BIOS Recovery Instructions Warning: Do not upgrade the BIOS unless your system has a BIOS-related issue. Flashing the wrong BIOS can cause irreparable damage to the system. In no event shall Supermicro be liable for direct, indirect, special, incidental, or consequential damages arising from a BIOS update. If you need to update the BIOS, do not shut down or reset the system while the BIOS is updating to avoid possible boot failure.
C7Z87-OCE User’s Manual To perform UEFI BIOS recovery using a USB-attached device, follow the instructions below. 1. Using a different machine, copy the "Super.ROM" binary image file into the disc Root "\" Directory of a USB device or a writeable CD/DVD. Note: If you cannot locate the "Super.ROM" file in your driver disk, visit our website at www.supermicro.com to download the BIOS image into a USB flash device and rename it "Super ROM" for BIOS recovery use. 2.
Appendix C: UEFI BIOS Recovery 6. After the process of BIOS Recovery is complete, press any key to reboot the system. 7. Using a different system, extract the BIOS package into a bootable USB flash drive. 8. When a DOS prompt appears, enter AMI.BAT BIOSname.### at the prompt. Note: Do not interrupt this process until BIOS flashing is completed.
C7Z87-OCE User’s Manual 9. After seeing the message that BIOS update is completed, unplug the AC power cable from the power supply to clear CMOS, and then plug the AC power cable in the power supply again to power on the system. 10. Press continuously to enter the BIOS Setup utility. 11. Press to load default settings. 12. After loading default settings, press to save the settings and exit the BIOS Setup utility.
Appendix D: Dual Boot Block Appendix D Dual Boot Block D-1 Introduction This motherboard supports the Dual Boot Block feature, which is the last-ditch mechanism to recover the BIOS boot block. This section provides an introduction to the feature. BIOS Boot Block A BIOS boot block is the minimum BIOS loader required to enable necessary hardware components for the BIOS crisis recovery flash that will update the main BIOS block.
C7Z87-OCE User’s Manual D-2 Steps to Reboot the System by Using Jumper JBR1 1. Power down the system. 2. Close pins 2-3 on Jumper JBR1, and power on the system. 3. Follow the BIOS recovery SOP listed in the previous chapter (Appendix C). 4. After completing the steps above, power down the system. 5. Close pins 1-2 on Jumper JBR1, and power on the system.
(Disclaimer Continued) The products sold by Supermicro are not intended for and will not be used in life support systems, medical equipment, nuclear facilities or systems, aircraft, aircraft devices, aircraft/emergency communication devices or other critical systems whose failure to perform be reasonably expected to result in significant injury or loss of life or catastrophic property damage.
