TM SUPERSAW MANUAL Cut any Surface!
SUPERSAW TM To reduce the risk of injury to your eyes never operate your power tool unless wearing goggles or, or properly fitted protective glasses with adequate top and side protection complying with ANSI Z87 "+" (or your applicable national standard). If there is a risk of injury to your face, SuperbrandTools recommends that you also wear a face shield or face screen over your goggles or protective glasses. Wear an approved safety hard hat to reduce the risk of injury to your head.
SUPERSAW TM thereafter at regular intervals (whenever the saw is shut off). If the saw chain becomes loose while cutting, switch off the motor, disconnect the chain saw from the power supply and then tighten. Never try to adjust the saw chain while the battery is connected! WARNING: After adjusting a saw chain, start the chain saw, let it run for a while, then switch motor off and recheck saw chain tension. Proper saw chain tension is very important at all times.
SUPERSAW TM when working on slopes or uneven ground. Watch for hidden obstacles such as tree stumps, roots, rocks, holes and ditches to avoid stumbling. There is increased danger of slipping on freshly debarked logs. For better footing, clear away fallen branches, scrub and cuttings. Use extreme caution when cutting small-size brush, branches and saplings because slender material may catch the saw chain and be whipped toward you or pull you off balance.
SUPERSAW TM issue, consult your employer, governmental agencies such as OSHA and NIOSH and other sources on hazardous materials. California and some other authorities, for instance, have published lists of substances known to cause cancer, reproductive toxicity, etc. asbestos or asbestos-containing products. If you have any reason to believe that you might be cutting asbestos, immediately stop cutting and contact your employer or a local OSHA representative.
SUPERSAW TM WARNING: When sawing, make sure that the saw chain does not touch any foreign materials such as rocks, fences, nails and the like. Such objects may be flung off, damage the saw chain or cause the chain saw to kickback. WARNING: If the rotating saw chain strikes a rock or other hard object, sparks may be created, which can ignite flammable materials under certain circumstances. Flammable materials can include dry vegetation and brush, particularly when weather conditions are hot and dry.
SUPERSAW TM the chain saw in a direction opposite to the saw chain movement at the point where the saw chain is slowed or stopped. This may fling the bar up and back in a lightning fast reaction mainly in the plane of the bar and can cause severe or fatal injury to the operator. Kickback may occur, for example, when the saw chain near the upper quadrant of the bar nose contacts the wood or is pinched during limbing or when it is incorrectly used to begin a plunge or boring cut.
SUPERSAW TM b) Do not operate power tools in explosive environments, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. c) Keep others away while operating. Operate only in an appropriate safety zone with adequate space between you and others. 2. ELECTRICAL SAFETY a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with grounded power tools.
SUPERSAW TM on the switch or energising power tools that have the switch on invites accidents. d) Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second. 5. BATTERY TOOL USE AND CARE a) Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pac may create a risk of fire when used with another battery pack.
SUPERSAW TM circuit each other or be short-circuited by other metal objects. When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or fire. i) Keep battery pack out of the reach of children. j) Seek medical advice immediately if a cell or battery has been swallowed.
SUPERSAW TM 1 8 2 3 4 5 6 7 COMPONENT LIST 1. GUIDE CHAIN 2. COMPRESSION NUT 3. GLAND NUT 4. SIDE COVER 5. POWER SWITCH 6. NON-SLIP HANDLE 7. LITHIUM BATTERY 8. GUIDE PLATE Inspect all components and accessories prior to first use to ensure there are no missing parts or visible damage/defect ACCESSORIES Screwdriver Original charger Original battery Wrench Only use the appropriate accessories intended for this tool.
SUPERSAW TM OPERATING STEPS 2 1 3 4 1 5 Loosen the screw nut counterclockwise and remove the side cover Align the hole, then install the guide plate and chain 2 3 Install the side cover and tighten the screw gland nut 4 Adjust Chain Tension Twist the Adjusting Screw Clockwise to tighten tension. Make sure the chain is not loose on the guide plate. 5 Insert the battery pack Note regarding Step #3: Tightening to an extreme level can cause contact between the side cover and chain.
SUPERSAW TM WORKING HINTS FOR YOUR CORDLESS RECIPROCATING SAW If your power tool becomes too hot, run no-load for 2-3 minutes to cool the motor. Avoid prolonged usage at very low speeds. Always use a blade suited to the material and material thickness to be cut. Always ensure the work-piece is firmly held or clamped to prevent movement. Any movement of the material may affect the quality of the cut.
