SRC-9310/9320 Touch Screen Remote Control User Manual 031021
SRC-93 SERIES User’s Manual Preface About this manual This manual is designed to make using the SRC-93 SERIES Touch Screen Remote Control as easy as possible. Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness of the contents. The information in this document is subject to change without notice. Copyright © Copyright 2003 This document contains proprietary information protected by copyright. All rights are reserved.
Table of Contents Chapter 1 - Introducing the SRC-93 SERIES.....................................1 SRC-93 SERIES Features .......................................................... 2 Unpacking the SRC-93 SERIES ............................................... 2 Identifying Components ....................................................... 3 Chapter 2 - Getting Started .............................................................4 Features Overview ..............................................................
SRC-93 SERIES User’s Manual Chapter 4 - Controlling Devices ................................................... 27 Selecting Device to Control ............................................... 27 Changing Touch Screen Page........................................... 27 Controlling the Device......................................................... 28 Using the AUX Key ................................................................ 28 Chapter 5 - Creating and Using Macros .....................................
Chapter 1 - Introducing the SRC-93 SERIES Congratulations on your purchase of the SRC-93 SERIES Touch-Screen Remote Control. The SRC-93 SERIES is a digital universal remote control that is easy to use, enabling you to control all of your electronic devices equipped with an infrared (IR) remote. The SRC-93 SERIES uses a touch screen panel and control buttons and is simple to use. Simply select a device and the appropriate screen appears.
SRC-93 SERIES User’s Manual SRC-93 SERIES Features The following list identifies the SRC-93’s key features. • • • • • • • Large touch screen display. Macro sequence function—each macro can store 60 commands. Controls up to sixteen devices including DVDs, TVs, Satellite Receivers, VCRs and CDs. Learns the IR codes from your existing remote controls to quickly set up devices. Pre-programmed manufacturer’s codes for many models.
Identifying Components Please refer to the following illustrations to identify the components of the SRC-93 SERIES. Infrared Eye Point the infrared eye at the device you want to operate. Battery Cover Remove this cover to insert Alkaline batteries. Touch Screen The Touch Screen panel enables you to configure and operate your devices by touching the screen. Tap the screen once to turn on the SCR-93 series.
SRC-93 SERIES User’s Manual Chapter 2 - Getting Started This chapter will give you the information you need to know to quickly get using the SRC-93 SERIES as your single remote control. Features Overview The following illustration highlights the different sections of the SRC-93 SERIES.
• • • • • • • • LCD Indicators: LCD stands for Liquid Crystal Display and these indicators at the top of the display give you feedback and information. You can look here to see if the beep is turned on, if the battery has low power, if the infrared signal was sent OK or if there was an ERROR, and also to see which page of Touch Screen buttons you are looking at. UART Port: This port allows you to connect the SRC-93 SERIES to a personal computer.
SRC-93 SERIES User’s Manual Installing Batteries The SRC-9310 operates on four AA Alkaline batteries, SRC-9320 operates on four AAA Alkaline batteries (batteries are not included). Batteries must be inserted before you can operate the SRC-93 SERIES. To insert the batteries, refer to the following illustration: Figure 3: Installing Batteries 1. Turn the remote over, push on the tab and lift the cover off. 2. Insert the batteries, matching the batteries to the (+) and (-) marks inside the battery case. 3.
Battery Low Indicator When the batteries are low, the battery low icon will be displayed in the upper left hand corner just above the SETUP button: When the battery Low Icon appears, you will not allowed to enter Functions Keys (SETUP Menu, DELETE Menu & MACRO Menu). Figure 4: The Battery Low Icon Battery Tips and Precautions • • • • • • • • Immediately replace the batteries when the battery low icon appears.
SRC-93 SERIES User’s Manual Touch Screen The touch screen reduces the number of buttons by changing its configuration for each device selected. In this way, the touch screen can provide a total of 768 buttons (16 devices x 2 pages x 24 buttons per page). Turning the Touch Screen On Using the touch screen is easy. Simply touch the screen to activate it. It will turn itself off after the user programmable power down time period.
immerse it in liquid. • Don't expose the SRC-93 SERIES to extreme temperatures. Keep it away from heat sources. • Avoid dropping the SRC-93 SERIES. • Don't drop anything on the touch screen. • Clean the LCD touch screen with a soft cloth. If needed, dampen the cloth slightly before cleaning. Never use abrasives or cleaning solutions. Touch Screen Buttons The touch screen buttons enable you to operate the SRC-93 SERIES and your external devices.
SRC-93 SERIES User’s Manual • Page / Date Button: Toggles from Page 1 to Page 2 of the Touch Screen buttons. If held down for more than two seconds, the date and year then week will be shown. • Power Button: Can turn off and on your devices but also during Touch Screen Layout (see page 15) will display all possible LCD choices. • Backlight / Sleep Button: Pressing it quickly will turn on the backlight, while holding it down for two seconds will enter the SLEEP Menu.
Setup Menu Menu Item Description page DATE Set the system clock and date. 40 NEW Create a new device from scratch. 13 CODE Assign a preprogrammed manufactures infrared code to a device. 17 LABL Rename a Device. 14 LAY Change the Touch Screen layout to you want to have based on all possible LCD choices. Learn infrared codes from an existing remote control. LRN 15 20 PWDN Set the automatic power off time period. 41 LITE Set the backlight time period.
SRC-93 SERIES User’s Manual Delete Menu Menu Item Description KEY Allow you to delete the infrared codes for a specific Touch Screen or Rubber button. BANK CODE: Allows you to delete all infrared codes for a specific device while leaving the Touch Screen layout the same. page 25 25 ALL: Deletes both infrared codes and the touch screen layout for a specific device. RST Resets the SCR-9310 back to factory settings.
Chapter 3-Setting Up the SRC-93 SERIES to Control a Device Before the SRC-93 SERIES can be used to control a device, it needs to be configured to display your existing remote control buttons and also programmed to send the correct infrared signals. This chapter guides you through the Touch Screen layout and SRC-93 SERIES setup procedure. Choosing a Device The first step is to choose a device to setup.
SRC-93 SERIES User’s Manual 1. Press the device key you wish to use for this device. For example, if this is a new TV you should press the TV button. For a new DVD player, press the DVD button. 2. Give your new Device a label. Use the UP and DOWN arrows to change the letter. Use the LEFT and RIGHT arrows to change the position. (Labels can be four digits long.) Press the OK button. 3. 4. Select one device attribute to load the default device screen. Use the UP and DOWN arrows to choose.
1. Use the device keys to select the device you want to label. 2. Use the arrow keys to give the device a new label. 3. Press OK when finished. Then press EXIT to leave the SETUP menu. Changing Touch Screen Layout The layout edit mode enables you to customize the SRC-93 SERIES's Touch Screen display to match your existing remote controls. The following steps show you how to make the display on the SRC-93 SERIES correspond to an existing remote.
SRC-93 SERIES User’s Manual 1. Press the device keys to select the device you want to modify. (ex. Press TV button) button (Page Button) to Press the change to the Touch Screen page you want to modify. button to show all Press the available LCD choices for all buttons. Press the Power button to show all possible LCD choices. 2. Touch the button that you wish to change. (You may change as many buttons as you wish.) 3. Each time you touch the button its appearance will change. 4.
configure all buttons on the SRC-93 SERIES for use with a specific manufacture model number. This feature is the fastest way to program the SRC-93 SERIES but requires that your device be located in Preprogrammed Code Table as the separate page with this manual. (Some newer or less-common devices may not be pre-programmed and must be learned using the Learning Function.) • Using the Learning Function: Use this method to directly learn the proper infrared signals from another remote control.
SRC-93 SERIES User’s Manual Press and hold the SETUP button on the Touch Screen. Press each number button (2, 4, 6, 8) until it disappears. Use the arrow buttons on the Touch Screen to select CODE and then press the OK button. 1. Use the device buttons to select the device you want to change. You will see the labels changing in the upper right hand corner of the screen. (ex. Press TV button) There are two ways to program the manufacture codes: • Manual Entry: Directly enter the code; go to step 2.
4. You may also use the TUNING buttons to increase or decrease the code. When finished, press the OK button to return to the Setup Menu. When you enter the Manufacture Code , but shows ‘ERROR’ message, two possibilities maybe caused : 1. That code number is not existed among the Manufacture Code table yet. 2. That code number is not in the range of Manufacture Code table reserved for the default device screen . To use automatic search: Automatic Search 5.
SRC-93 SERIES User’s Manual The AUTO mode‘s preprogrammed code circle depends on the range of Manufacture Code table reserved for that default device screen. Ex. TV’s preprogrammed code circle will be from 0 ~255. Using the Learning Function If you have the original remote, the SRC-93 SERIES has the ability to directly learn infrared codes.
Learning from Another Remote Control To teach the codes from your remote, set both remotes on a flat surface facing each other. Be sure to point your device’s remote control at the SRC-93 SERIES’s learning eye, which is located at the bottom of the unit. Do not use the other eye located at the top of the SRC-93 SERIES. You do not have to turn on the actual device (TV, VCR, etc…). Refer to the following illustration.
SRC-93 SERIES User’s Manual To learn infrared codes directly from a device’s remote control, follow these steps: Press and hold the SETUP button on the Touch Screen. Press each number button (2, 4, 6, 8) until it disappears. Use the arrow buttons on the Touch Screen to select LRN and then press the OK button. 1. Use the device keys to select the device you want to program. Make sure the other remote control is pointed directly at the SRC-93 SERIES’s Learning eye. Keep them 2~4 inches apart.
3. Press and hold the button on the other remote control for 2 seconds. 4. Check to see whether ERROR or OK on the top of the SRC-93 SERIES Touch Screen is displayed. If ERROR is displayed, try again. (You have to hold the other remote control’s button for about 2 seconds before letting go.) The SRC-93 SERIES will automatically guide you to the next button to program by flashing it on the Touch Screen. When all buttons are programmed on the current page it will automatically switch to the next page.
SRC-93 SERIES User’s Manual Collecting Unrecognized Infrared Codes Use this procedure if the SRC-93 SERIES is unable to recognize the infrared signals from another remote control. (You only see the ERROR indicator when Using the Learning Function on page 20.) Once collected you can use the Remote Connector (see Appendix B - Accessories on page 44 for more info) to upload the unrecognized codes to your personal computer and then email them to SUNWAVE for analysis.
Deleting a Specific Key To erase the infrared codes for a specific Touch Screen or Rubber key, follow these steps: Press and hold the DELETE button on the Touch Screen. Press each number button (2, 4, 6, 8) until it disappears. Use the arrow buttons on the Touch Screen to select KEY and then press the OK button. 1. Select the device that has the key that you want to erase. (ex. Press TV button) 2. 3. Select the key you want to erase. If you want to erase more keys, you may select them now. 4.
SRC-93 SERIES User’s Manual To delete a device from the SRC-93 SERIES follow these steps: Press and hold the DELETE button on the Touch Screen. Press each number button (2, 4, 6, 8) until it disappears. Use the arrow buttons on the Touch Screen to select BANK and then press the OK button. 1. Use the Arrow keys to chose: CODE: Erase infrared codes only but keep Touch Screen display the same. ALL: Erase both codes and Touch Screen layout. 2. Select the device you wish to delete.
Chapter 4 - Controlling Devices The SRC-93 SERIES is designed to be simple and straight forward to operate. This chapter explains how to use the SRC-93 SERIES to control all your devices. This Chapter assumes you have already setup the SRC93 SERIES and assigned Infrared codes to different buttons. See Chapter 3-Setting Up the SRC-93 SERIES to Control a Device on page 13 for more information on assigning codes. Selecting Device to Control 1. Press one of the eight device buttons to pick the device.
SRC-93 SERIES User’s Manual Controlling the Device Make sure the SRC-93 SERIES is pointing at the device you are trying to control and simply press the button you want to send: • Press the Touch Screen buttons. • Press one of the rubber buttons on the bottom half of the SRC-93 SERIES’s. Record Button Must Be Held Down for 2 Seconds: As a safety feature, the record button needs to be pressed for 2 seconds. This is to prevent accidentally pressing the VCR record button and overwriting a tape.
Chapter 5 - Creating and Using Macros Introduction to Macros A macro is simply a series of commands. The MACRO feature enables you to initiate a sequence of up to 60 commands with a single button. You can create a macro on any control button and also insert time delays into the sequence. Remember, however, assigning a macro eliminates the button's original function.
SRC-93 SERIES User’s Manual Set up the macro using the following steps: Press and hold for two seconds the MACRO button on the Touch Screen. Press each number button (2, 4, 6, 8) until it disappears. Use the arrow buttons on the Touch Screen to select KEY and then press the OK button. 1. Select a device using the device buttons on the SRC-93 SERIES. (ex. Press TV button) 2. On the Touch Screen select one of the buttons to assign the macro to. You will hear two beeps.
6. 7. Press the DVD device button. Press the POWER button. 8. Press the TIME DELAY button. 9. Use the UP and DOWN arrows to select a time delay (in seconds). Press OK to confirm time delay. 10. Press the PLAY button. 11. Press OK to save the Macro. Then press EXIT to leave the MACRO Menu.
SRC-93 SERIES User’s Manual Using Macros To start a Macro for a specific device, first select the device and then simply press the key assigned to the Macro. If you forget which keys have Macros assigned to them, press the MACRO button and all keys with valid Macros will be shown. During the Macro transmission, all commands will be shown on the Touch Screen as they are sent. Deleting a Macro Deleting a Macro is actually simply a matter of deleting the key that the Macro has been assigned to.
Chapter 6 - Other Features The SRC-93 SERIES has the following additional features: • Timers: Can be used to start a macro or send a command at a later time. Many timers are available including: daily, weekly, weekends only, weekdays only, or specific days and times. • Quick Channel Lists: Used to group certain TV or Satellite channels together. For example, group all news channels together to make it easy to cycle through only the news channels.
SRC-93 SERIES User’s Manual Setting Up a New Timer Press and hold the MACRO button on the Touch Screen. Press each number button (2, 4, 6, 8) until it disappears. Use the arrow buttons on the Touch Screen to select TIMR and then press the OK button. 1. Choose one of the eight available timers by pressing the number on the Touch Screen. 2. 3. 34 Use the arrow keys to select the timer type. Press OK to confirm timer type.
4. 5. Use the arrow keys to select the time. Press OK Note: If you used SPEC (Specific Day/Time) you will also set the date. 6. Select the key that the timer will press. If you want you can switch devices (use device keys) or Touch Screen pages. (Use the button.) At the selected time and date, the SRC-93 SERIES will send the infrared code or start the macro associated with the key selected in step 6. When finished press the EXIT key to leave the MACRO Menu.
SRC-93 SERIES User’s Manual Setting up Quick Channel Lists Press and hold the MACRO button on the Touch Screen. Press each number button (2, 4, 6, 8) until it disappears. Use the arrow buttons on the Touch Screen to select Q CH and then press the OK button. 1. Use the device keys to select a device and the Page button to select a Touch Screen page. 2. Use the number keys to enter a channel number (0~9,10,ENTER).
Deleting Channels from a Quick Channel List Press and hold the DELETE button on the Touch Screen. Press each number button (2, 4, 6, 8) until it disappears. Use the arrow buttons on the Touch Screen to select Q CH and then press the OK button. 1. Use the device keys to select a device and the Page button to select a Touch Screen page. 2. Select the Quick channel you want to delete. (The selected classification will flash.) 3.
SRC-93 SERIES User’s Manual Using Quick Channel Lists Press the Quick Channel button you wish to use. (It will begin to flash.) Now use the Channel Up and Channel Down buttons to scroll through all channels in this classification. When finished, press the Exit button again to return to normal operation. Transmitting System Setup The SRC-93 SERIES allows transmission of system setup to a personal computer or another SRC-93 SERIES.
Using Sleep Mode Sleep mode allows the SRC-93 SERIES to send a command or start a Macro after a specified time delay. One example is you could use sleep mode to shut off a TV after you have already fallen asleep. To use sleep mode: 1. 2. 3. Press and hold the BACKLIGHT (SLEEP) key for two seconds. Use the arrow keys to specify the sleep timeout period. (24 hours maximum) Press OK to confirm. Select the Device using the device keys 4.
SRC-93 SERIES User’s Manual Displaying Version Number For technical support reasons, the version number might be needed by SUNWAVE. To display the two version number of PROG and DATA, use the VER selection in the SETUP Menu. Chapter 7 Changing SRC-93 SERIES Parameters Many of the SRC-93 SERIES parameters can be changed. This chapter explains the different customizations you can make.
Power Down Time Period This setting specifies the time delay the SRC-93 SERIES will wait until it automatically shuts down. (The touch screen will go blank to conserve battery usage.) This setting can be changed from 1 minute to 90 minutes by using the PWDN selection of the SETUP menu: 1. Use the arrow keys to set the power down time. Press OK when finished and EXIT to leave to the SETUP Menu.
SRC-93 SERIES User’s Manual Beep Toggling This setting specifies whether you want the SRC-93 SERIES to beep each time a button is pressed. Use the BEEP selection in the SETUP Menu to change this setting: 1. Use the OK button to toggle the beep from ON to OFF. Resetting to Factory Defaults This setting will erase all user specified settings (ex. PWDN, LITE…) and reset the SRC-93 SERIES back to factory defaults. Also the learning codes, Q CH will be erased.
Appendix A - Specifications Model SRC-9310 SRC-9320 3.2" x 7.3" x 1.2" 3.2" x 7.3" x 1.1" (8.2cm x18.5cm x 3.2cm) (8.2cm x18.5cm x 2.9cm) Weight (Without Batteries): 7.8oz (220g) 7.8oz (220g) Number of Device: 16 devices 16 devices 2.7" x 3.2" 2.7" x 3.2" (6.0cm x 8.0cm) (6.0cm x 8.
SRC-93 SERIES User’s Manual Appendix B - Accessories SLC–2080 USB cable Transmit wire The SLC–2080 is an optional link cable that enables transmission of system setup to a personal computer or another SRC-9310/9320. With the RemoteComm software enables user to customize the remote control, create macros and timers. With the Upgrade Tools enables user to upgrade program and Preprogrammed code. ● Upgrade Memory: Memory include Preprogrammed code & User’s setup data.
Appendix C - Troubleshooting Problem Solution LCD does not show anything when you touch it or press the rubber buttons. Batteries may be dead. Replace the batteries with 4 new AA Alkaline Batteries. (page 6) The SRC-93 SERIES doesn’t operate a device. Make sure that the desired device screen on the SRC-93 SERIES LCD panel has been selected. Check that the batteries are properly installed. Move closer to the device. The maximum operating distance is approximately 30 feet.
SRC-93 SERIES User’s Manual Problem Solution You cannot operate a device even after teaching the device using the learning function. Make sure that you have correctly “taught” your device’s remote control to the SRC-93 SERIES. (page 21) Delete the device data from the SRC-93 SERIES and carry out the learning function again. (page 25) Make sure you did not program more than one remote for a given device. You see “ERROR” display on the LCD during the learning procedure.
Problem Solution A button of your existing remote performs two or more functions Some remotes issue multiple commands when a button is held down. Please be sure to teach different buttons of SRC-93 SERIES for these different commands. Each button of SRC-93 SERIES can only learn one command. The LCD screen turns off. The SRC-93 SERIES is preset automatically to switch the LCD off after the Power Down time. Just tap the LCD screen or any button to turn the SRC-93 SERIES back on again.
