SRC-7000 Touch Screen Smart Remote Control User’s Manual 041201
Preface Preface About this manual This manual is designed to make using the SRC-7000 Smart Remote Control as easy as possible. Information in this document has been carefully checked for accuracy and is subject to change without notice. Copyright © Copyright 2005 This document is protected by the international copyright law. No part of this publication may be reproduced by any means without the permission of SUNWAVE Technology Corporation in Taiwan.
Table of Contents Preface ................................................................................... i Table of Contents ................................................................. 1 Chapter 1 Introduction to the SRC-7000 ............................ 4 1.1 SRC-7000 Features....................................................... 5 1.2 Unpacking the SRC-7000............................................. 5 1.3 Battery Installation ....................................................... 6 1.3.
Chapter 3 How to Set Up Your SRC-7000........................ 21 3.1 Add a Device ............................................................... 21 3.1.1 Create a New Device ........................................................................ 21 3.1.2 Load the Codes for the Newly-added Device.................................... 23 A. Pre-code ....................................................................................................... 23 B. Learning............................................
Chapter 4 Menus ............................................................... 52 4.1 Set Up the Remote ..................................................... 52 4.2 Key Layout .................................................................. 56 4.3 Code Setting ............................................................... 57 4.4 Timer Macro ................................................................ 58 4.5 Duplicate .....................................................................
Chapter 1 Introduction to the SRC-7000 Congratulations on purchasing SRC-7000 Smart Remote Control (SRC-7000). The SRC-7000 is a digital Universal Remote Control with smart design that is easy to configure and use, enabling you to control all your IR equipped electronic devices. One of the main features is the touch screen control panel, which can integrate a number of remote controls in one and reduce the number of buttons for each device. The design makes it easy for you to find the function you want.
Chapter 1 Introduction to the SRC-7000 1.1 SRC-7000 Features This following list identifies SRC-7000 key features. For more information on getting the most, please refer to the following chapters. 1. Control up to 64 devices including VCD/DVD, TV, Satellite, VCR, CD/MD, Receiver/Tuner, Tape, etc. 2. Large LCD touch-screen display with automatic backlighting for visibility in low light environments. 3.
SRC-7000 User’s Manual 1.3 Battery Installation Please refer to the following illustration and instructions for inserting the batteries 1. Remove battery cover. 2. Insert batteries. Ensure that you insert the batteries according to the marking inside the battery case. Figure 1-1: Inserting the batteries The battery compartment is located at the back of SRC-7000. 1. 2. 3. Put your thumb in the battery cover slot and pull to remove the cover.
Chapter 1 Introduction to the SRC-7000 1.3.1 Battery Precautions Please pay attention to the following instructions: 1. Be sure that the positive (+) and negative (-) polarities of each battery match the polarities indicated in the compartment. 2. Do not expose the batteries to excessive heat or flame. 3. Keep the batteries away from children. 4. Low power batteries will reduce the effective distance of the unit. 5. Do not mix different type of batteries or mix new and used batteries at the same time.
SRC-7000 User’s Manual 1.5 Identifying Components Please refer to the following illustrations to identify the components of SRC-7000. This section provides you an overview of the SRC7000. For the detailed description on operation, please refer to Chapter 3. 1.5.1 Top of SRC-7000 1. Light sensor (P.54) The Light Sensor will detect the ambient brightness to control the backlight whether turn on or not. 2. Touch screen LCD (P.
Chapter 1 Introduction to the SRC-7000 1.5.2 Botton of SRC-7000 1. IR port This needs to be pointed to the IR receiver of the targeted device. 2. Reset switch You can reset the SRC-7000 when the SRC-7000 does not work properly or hangs up (freezes). 3. Rear label The rear label marks the model number and the brief specifications. 4. Buzzer opening Beep tone signals are transmitted through here. 5. Battery compartment Contains the 3xAAA Alkaline batteries or Ni-MH rechargeable batteries. 6. Learning eye (P.
SRC-7000 User’s Manual 1.5.3 Direct Access Buttons ( Rubber Keys) The Direct Access Buttons provide you with easy access to oftenused functions such as volume, channel control, skip to the next, skip to the previous, reverse, play and stop… etc. Before use, these functions must be set. (Refer to Chapter 3: How to Set Your SRC-7000, Page21.
Chapter 1 Introduction to the SRC-7000 1.5.4 LCD Touch Screen The LCD (Liquid Crystal Display) touch screen enables you to configure and operate your SRC-7000 with the touch of a finger. 1.5.5 Precautions When Using the Touch Screen Please pay attention to the following instructions to avoid damaging your SRC-7000. 1. 2. 3. 4. 5. 6. 7. 11 Do not tap hard on the LCD touch screen. Tap the LCD touch screen gently. Do not use a pen or any sharp object to tap the screen. Do not immerse it in liquid.
SRC-7000 User’s Manual 1.5.6 Touch Screen Keys The touch screen keys enable you to control your devices as you would do with your original remote control. You can also set up macros, program timers, cycle keys and configure the LCD screens as you want. Figure 1-6: Touch screen buttons It is very easy to use the touch screen. You just need to tap the soft buttons to activate the specific function. Before use, you have to set up the SRC-7000. (Refer to Chapter 3 How to Set Your SRC-7000, Page 21.
Chapter 1 Introduction to the SRC-7000 Introducing the frequently used LCD Layout as followed: y Main Menu Press the Menu button Main Menu. n o p to call up the Accesses Timer Macro. (P.45.) Accesses basic information about the remote. (P.14.) Device key q Tap the right or left icon to change the pages. r Page indicator. It reads that you are in the first page of a total of 2 pages. You can input 8 pages in the Main Menu. y Device Layout Tap the device key directly to enter the device page.
SRC-7000 User’s Manual y Basic Information Layout After pressing the icon, you can get the basic information as follow: n Date information (P.52) o Time information (P.52) p Buzzer information (P.52) q Batteries power indicator (P.52) r Program version s Pre-programmed code version y Timer Macro Layout After pressing the icon, you can get the Timer Macro layout as follow: n Tap the Timer Macro key directly to start the macro function. (P.
Chapter 1 Introduction to the SRC-7000 y Setup Menu Layout When you are under the setup status you will see the icons as follows: n Help Guide: Tap this icon to get the setup process information. You can press or reading the tips, press o to read the information pages. After button to exit. Quick Icon: Under the setup mode you will see the icons show on the top right of the screen. The fastest way to edit SRC-7000 is tapping the icon directly to change the edit functions directly.
SRC-7000 User’s Manual Timer Macro Setup Mode o Tap the icon directly to change the functions in Timer Macro. Add / Edit the Timer Macro (P.45) Re-label the Timer Macro (P.48) Delete Timer or Macro (P.47) View Macro processes (P.49) * When you are adding or editing the macro processes two icons appear as below: n When setting the Macro processes tap this icon to go back to last Macro step. (P.45) o Set delay between two commands. (P.
Chapter 2 Quick Start This chapter shows you how to quickly set up the SRC-7000, for a more detailed set up please refer to Chapter 3. At turn on, the SRC-7000 will show the welcome greeting message on the screen. From now on, you formally enter the setup procedure. Please operate by the following instructions step by step. 2.1 Re-calibrating the Screen You will need to re-calibrate SRC-7000’s touch panel in three conditions: a. When you insert the batteries at the first time. b.
SRC-7000 User’s Manual 2.2 Date / Time Setting 1. Press button for 2 seconds for entering Setup Menu. 2. Scroll the press or buttons to choose Setting item and button for entering “Setting” menu. 3. Scroll the or buttons to select Date item and press button for confirmation. After you will find the year column underlined, meaning it is ready for current date to be entered by pressing and button. To move the underline forward and backward to target any +column press and button. 2. 3. 5. 4.
Chapter 2 Quick Start 2.3 Device Setting SRC-7000 will automatically get through the setup mode when you operate the SRC-7000 for the first time. 1. Select the targeted device you wish to set up. Please tap the target device key in the Main Menu to enter “Setup device” menu. (ex. “TV” device) 1. 2. 3. * Pre-code: load pre-programmed IR code from the factory default (no guarantee being able to control all brand devices). 2.
SRC-7000 User’s Manual If the codes are not correct please repeat steps and select “All”. Repeat the ~ again to find the proper code for your target device. 4. Finally, press the button to load the code and exit. If you didn’t get the correct remote codes from the “Pre-programmed code list” item, or you did the wrong steps, please try the other ways to re-setup or supplement. a. Use Pre-code function to load current remote codes. (Please refer to 3.1.2 A. Pre-code P.23.) b.
Chapter 3 How to Set Up Your SRC-7000 In this chapter, you can find all the topics about how to setup the SRC7000. Each topic has its detailed instruction. You can easily customize the SRC-7000 by the procedures. 3.1 Add a Device With this function, you are able to create a new device for the SRC7000. There are two main stages for you to add a device successfully. The first one is to create a new device in the main menu. The second one is to load the specific codes for your newly-added device. 3.1.
SRC-7000 User’s Manual 4. 4. 5. Please choose two points within the desired block on LCD & . A “v” symbol will appear where you tapped. After you determine the second point , the key frame will show up on the screen automatically. Tap the frame to confirm the location. If you want to relocate the points, you can press the button to quit. 5. a. The size of the key will depend on the points you choose. b. You cannot setup a device that will overlap the adjacent key.
Chapter 3 How to Set Up Your SRC-7000 6. 7. 6. Please decide the “Device Category” for your device by pressing the or buttons. Press the to confirm and enter next step. 7. Finally, please decide how you will load the IR remote codes for the device. There are three choices for you: “Pre-code”, “Learning” and “Done”. For more detail please refer to the following sections to get further understanding. 3.1.
SRC-7000 User’s Manual 1. 2. 3. 1. Decide the “Device Category” for your device by pressing the or buttons. Press the to confirm and enter to next step. 2. Decide how you will load the IR remote codes for the device. to confirm. Select “Pre-code” press Choose the first letter of targeted device brand (ex. “S” on behalf of Sony, Samsung…etc), and point the SRC-7000 at the targeted device. After selecting “Brand” item, please turn on your target device. Tap soft button to start auto searching.
Chapter 3 How to Set Up Your SRC-7000 B. Learning With this function, the SRC-7000 is able to learn IR remote codes directly from your original remote. You can also learn codes if you fail to get the right remote codes in the pre-programmed code database. When using the learning function, please have your original remote pointed to the “Learning Eye” at the bottom of SRC-7000 as the Figure 3-1.
SRC-7000 User’s Manual When you have successfully added a new device, and want to learn the codes for the device, choose the “Learning” item to program the unit. 1. 2. 1. Decide the “Device Category” for your device by pressing the or buttons. Press the to confirm and enter to next step. 2. Decide how you will load the IR remote codes for the device. Select “Learning” press to confirm. = 3. 3. The first page will guide you to learn the rubber keys on SRC7000.
Chapter 3 How to Set Up Your SRC-7000 4. Learning successfully Learning fail 4. 5. Press the corresponding key on your original remote for about 2-3 seconds until the symbol shows up on the LCD to make sure the SRC-7000 has learnt the code. 5. If the symbol shows up, it means that the SRC-7000 has failed to learn the remote codes. If the SRC-7000 fails to copy the remote code, please repeat step 3 again. 6. Press the button when you have finished learning all keys.
SRC-7000 User’s Manual 1. Please press the button for about 2 seconds to enter Setup Menu. And then enter “Key Layout” menu. Add Key” item and then enter the submenu. On 2. Select the “ tapping the soft key, you will see the indication for the function. After button to go to next step. reading the tips, please press the 3. Select the device you want to add the key. After entering the device, please choose two points from the blocks on LCD to determine the key location & .
Chapter 3 How to Set Up Your SRC-7000 3.3 Adding Text With this function, you are able to add a text for description. 1. 2. 3. 1. Press the button for 2 seconds to enter Setup Menu. And then enter “Key Layout” menu. 2. Choose the “ Add Text” item and then you will enter the submenu. On tapping the soft key, you will see the indication for the function. After reading the tips, please press the button to go to next step. 3.
SRC-7000 User’s Manual 6. You will be able to see the new-added text on the LCD layout. 7. If you intend to add another text, please repeat step 3~6. a. The length of text you can add to the description will depend on the points you choose. b. You can add text to not only just a specific device but a soft key also. To add a description to a soft key, you simply need to choose the specific device in advance and follow the former steps. 3.
Chapter 3 How to Set Up Your SRC-7000 3. Please select the device you want to rename. 4. 4. 5. 6. Next you will need to make a decision: to re-label the device itself or to go into the device to re-label its soft keys. Re-label device: If you decide to re-label the device, please key button to confirm in the new name. And then press the your decision. Into device: If you decide to re-label the soft key in the device, please choose the key you want to rename and key in the new name. 31 5.
SRC-7000 User’s Manual 3.5 Re-size a Device, Key or Text With this function, you are able to re-size a device, soft key or text. You can also use the function to change the locations for them. 1. 2. 3. 1. Press the button for 2 seconds to enter Setup Menu. And then enter “Key Layout” menu. 2. Re-size” item and then you will enter the Choose the “ submenu. On tapping the soft key, you will see the indication for the function. After reading the tips, please press the button to go to next step. 3.
Chapter 3 How to Set Up Your SRC-7000 6. After you determine the second point, the key frame will show up on the screen automatically. Tap the frame to confirm the location. 7. After finished the edit, press the decision. 8. If you intend to re-size another key, please repeat step 3~7. button to confirm your The way to re-size a soft key is similar to the way to add a soft key. You cannot revise a soft key device that will overlap the adjacent keys. 3.
SRC-7000 User’s Manual 4. 5. 6. 4. Then you will need to make a decision: to delete the device itself or button to to go into a device to delete the soft keys. Press the confirm the selection. 5. If you select a device to delete, you will see a message to confirm your decision. Please choose “Yes” or “No” then press the to confirm your decision. 6. If you intend to delete another device, please repeat step 3~5. 7.
Chapter 3 How to Set Up Your SRC-7000 3.7 Pre-programmed Code SRC-7000 is equipped with a large pre-programmed code database. With this function, you are able to load the code for your device. It also enables you to control your device even if you lose your original remote. 1. 2. 3. 1. Press the button for 2 seconds to enter Setup Menu. And then enter “Code Setting” menu. 2. Choose the “ Pre-code” item and then you will enter the submenu.
SRC-7000 User’s Manual Tap soft button to start auto searching. When you see the targeted device has been turned off, tap or press any button to test the immediately to stop auto searching. Then press power key. If it can’t work, please go through step as below. Tap or gently to figure out the correct remote code (Code number as shown on the top middle position of the LCD.) until the targeted device has been turned on again. Press the power key or the hard key to test and to confirm the codes.
Chapter 3 How to Set Up Your SRC-7000 3.8 Learning With this function, you are able to use the SRC-7000 to learn IR remote codes directly from your original remote. You are able to control your devices with the SRC-7000, even if the code for your device is not included in the database. a. Although the learning function is able to copy almost all the IR remote codes, there are still some special codes that the SRC7000 cannot learn. b.
SRC-7000 User’s Manual 1. 2. 3. 1. Press the button for 2 seconds to enter the Setup Menu, then enter the “Code Setting” menu. button to enter 2. Select the “ Learning” item then press the the submenu. You will need to see the help guide for the learning button to go function. After reading the tips, please press the to the next step. 3. Select the device for which you want to learn the remote codes. = 4. 5. 4. The first page will guide you to learn the rubber keys on SRC-7000.
Chapter 3 How to Set Up Your SRC-7000 Learning successfully Learning fail 6. 7. 6. Press the corresponding key on your original remote for about 2-3 seconds until the symbol shows up on the LCD to make sure the SRC-7000 has learnt the code. 7. If the symbol shows up, it means that the SRC-7000 has failed to learn the remote codes. If the SRC-7000 fails to copy the remote code, please repeat this step again. 8. Press the button when you have finished learning all keys. 9.
SRC-7000 User’s Manual 3.9 Learn a Cycle Key Some devices save a circle of commands in one button. The SRC-7000 is equipped with a special Cycle function; with this function you are able to replicate the circle of commands. 1. 2. 3. 1. Press the button for 2 seconds to enter the Setup Menu, and then enter the “Code Setting” menu. Cycle” item and then press the 2. Choose the “ enter the submenu. button to 3. Choose the device where you want to put the Cycle key. 4. 5. 6. 4.
Chapter 3 How to Set Up Your SRC-7000 this Cycle key. (You can save up to 6 cycle commands in the Cycle key.) button when you have finished learning all the 6. Press the circle of commands. 7. If you intend to setup another “Cycle key”, please repeat step 4~6. When you have saved some commands in a Cycle key, a sign will be marked on the Cycle key. 3.10 Delete Device / Key Codes With this function, you can delete the “Codes” in the keys. 1. 2. 3. 1.
SRC-7000 User’s Manual 4. And then you will need to make a decision: to either delete all of the codes for the device, or to go into the device to delete the codes for the keys. If you select a device to delete, you will see a message to confirm your decision. Please choose “Yes” or “No” to confirm your decision. 5. If you go into the device to delete the codes for its keys, you can delete the codes by tapping the soft keys directly. 6.
Chapter 3 How to Set Up Your SRC-7000 1. 2. 3. 1. Press the button for 2 seconds to enter the Setup Menu, and then enter the “Code Setting” menu. 2. Choose the “ Macro” item and then enter the submenu. On pressing the soft key, you will see instructions on how to use the button to go to the function. After reading the tips, press the next step. 3. Select the device where to set the Macro key. 4. a. 5. 4. Select the commands you want to save in the Macro key step by step.
SRC-7000 User’s Manual An Example of setting a Macro Basic device operation for watch DVD: 1. 2. 3. 4. 5. Turn the TV on. Switch the TV to video mode. Turn the DVD on. Create a two-second delay. Instruct the DVD to play a disc. The commands for the Macro key. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. Press the TV device button. Press the Power button. Press the TV/Video button. Press the DVD device button. Press the Power button. Press the Time Delay icon.
Chapter 3 How to Set Up Your SRC-7000 3.11.2 Timer Macro A. Create a Timer Macro The “Timer Macro” function enables you to set devices to turn on at specified times, or to operate a Macro function automatically at a specific time. The function helps you to record movies, turn on music, act as an alarm clock, or implement Home Automation. You can enjoy this marvelous convenience after setting the Timer Macro. The SRC-7000 is quipped with 32 sets of Timer Macros. 1. 1. 2. 3. 4. 45 2. 3.
SRC-7000 User’s Manual 4. 5. 6. Select any key in devices for the commands to use for the Macro. You can save up to 60 commands in one Macro. Select the operation processes between any devices. Select the commands to use. a. You can press the icon to set up the delay between two commands from 0 ~30 seconds. b. You can press the icon to go back to the former command you selected. Press the 7. button to confirm the Macro processes setting. 8. 9. 7.
Chapter 3 How to Set Up Your SRC-7000 B. Delete Your Timer Macro With this function, you are able to delete Timer Macros. 1. 1. 2. 3. 4. 4. 2. 3. Press the button for 2 seconds to enter Setup Menu, and then enter the “Timer Macro” menu. Choose the “ Delete” item and then enter the submenu. Select the Macro/Timer key you intend to delete. 5. Decide if you want to delete the Macro or the Timer. You can only delete the Timer only. Choose “Yes” to confirm the delete.
SRC-7000 User’s Manual C. Re-label Your Timer Macro With this function, you can easily re-label your Timer Macros. 1. 2. 3. 1. Press the button for 2 seconds to enter Setup Menu, and then enter the “Timer Macro” menu. 2. Choose the “ Re-label” item and then enter the submenu. 3. Select the Timer Macro you intend to re-label. 4. 5. 4. Key in the new name for the Timer Macro, and then press button to confirm your decision. the 5. The new label for the Timer Macro will show on the list.
Chapter 3 How to Set Up Your SRC-7000 D. View Your Timer Macro With this function, you are able to view all the Macro commands and the timer in the Timer Macro you selected. 1. 2. 3. 1. Press the button for 2 seconds to enter Setup Menu, and then enter the “Timer Macro” menu. view” item and then you will enter the 2. Choose the “ submenu. and 3. Select the Time Macro you intend to view. Press to view the commands in turns. 4. Tap the icon to view the timer.
SRC-7000 User’s Manual 3.12 Set Up Your Favorite Channels You can use the Macros to save your favorite channels. This enables you to get to your favorite channels just by tapping Macros. There are two main steps you need complete: Add some soft keys as Macros and set these Macros as your favorite channels. 3.12.1 Add Favorite Channel Keys Decide where your favorite channels will be located. You can create these keys in any device or just in the Main Menu. 1. 2. Refer to Section 3.
Chapter 3 How to Set Up Your SRC-7000 3.12.2 Set Your Favorite Channels as Macros This is done in the same way as you set a Macro (refer to 3.11.1 Macro on page 42). Enter “Macro” in “Code Setting”, and then choose one of the soft keys you can just create as your Macro key. 1. Press the button to go back to the MENU list, select “TV” and input the favorite channel number in this Macro key. (ex: CNN channel 97; HBO channel 56) nSelect the CNN key to assign as a Macro start key.
Chapter 4 Menus 4.1 Set Up the Remote The steps for entering detailed settings in the setting menu are as follows: 1. Press the button for 2 seconds to enter the Setup Menu. or and choose the “ Setting” item, button for entering the “ Setting” menu. 2. Scroll the cursor then press the 3. Select the items as follows to set up your SRC-7000. 2. 3. or buttons or tap the screen to select the item. 4. Press the The item you select will be marked in black. 5. You can press or to change the pages. 6.
Chapter 4 Menus Date Time Buzzer Power Contrast 53 Use this function to set the date for your remote. or to choose the year, month and date. 1. Use or to change the date values. 2. Use to save your settings or press to exit 3. Press without saving any changes. Use this function to set the time for your remote. or to choose the time system (24hr / 12hr). 1. Use or to change the time values. 2. Use to save your settings or press to exit 3. Press without saving any changes.
SRC-7000 User’s Manual LCD Off Light Sensitivity Light Period Use this function to change the idle time (when no functions are used) before turning off the Display. or to change the idle time before the LCD 1. Use turns off. 2. Idle time can be set up to 600 seconds. (Disable/10sec ~600sec). 3. You can use this function to increase battery life (lower time for increased battery life). to save your settings or press to exit 4. Press without saving any changes.
Chapter 4 Menus Motion The Motion Detector will sense any movement and turn on the Display automatically. Use this function to change the sensitivity of the Motion detector (Off/Slow/Medium/Fast). or to change the sensitivity of the Motion 1. Use Detector. 2. The more sensitive (eg: Fast), the more easily the SRC7000 will turn on its LCD. 3. You can use this function to conserve battery power (a faster setting will decrease amounts of accidental activation). to save your settings or press to exit 4.
SRC-7000 User’s Manual 4.2 Key Layout Add Device Use to add your devices to the SRC-7000. You can use “Pre-code” or “Learning” to load the codes for the device (Please refer to Chapter 3.1 Add a Device on page 21). Add Key Use to add new keys to your devices on the SRC-7000. You can use “Pre-code” or “Learning” to load the codes for the device (Please refer to 3.2 Add a Soft Key on page 27). Add Text Use to add a description for a specific device key or key (Please refer to 3.3 Adding Text on page29).
Chapter 4 Menus 4.3 Code Setting Pre-code Use to load the pre-programmed codes for your devices. (Please refer to 3.7 Pre-programmed Code on page 35). Learning Use this function to learn the IR codes from your remotes. (Please refer to 3.8 Learning on page 37). Macro Cycle Del. Code 57 Use to add Normal Macros to your SRC-7000. You can use all keys except device keys as your Normal Macros. *You cannot set a timer for a Normal Macro. (Please refer to 3.11 Create a Macro on page 42).
SRC-7000 User’s Manual 4.4 Timer Macro Add / Edit Delete Re-label View Use to add or edit your Timer Macros on your SRC-7000. You can set the Timer for the Macro at the same time. There are 32 sets of Timer Macros you can use. (Please refer to 3.11.2 A. Create a Timer Macro on page 45). Use to delete your Timer Macros on your SRC-7000. (Please refer to 3.11.2 B. Delete Your Timer Macro on page 47). Use to rename your Timer Macros on your SRC-7000. (Please refer to 4.
Chapter 4 Menus 4.5 Duplicate You can connect two SRC-7000s with the Transmit Cable (Appendix B P.71) to duplicate the settings on one remote and transfer them to another unit. Duplicate With this function, you are able to transfer your settings to another SRC-7000 using the Transmit Cable. 1. Connect two SRC-7000s, “A” and “B”, by using the Transmit Cable. 2. If you intend to transfer the settings on the SRC-7000 unit “A” to unit “B”, use the SRC-7000 unit “A” to start the duplication. 3. 4. 5. 3.
SRC-7000 User’s Manual 5 6. 6. If the duplication is completed successfully, a message will show up to tell you the completion. If the duplication is not successful, please repeat from step 1 again. If a message “Duplicate Fail” shows up, please check the following points: a. The cable is properly connected at both ends. b. The batteries in both remotes with sufficient power.
Chapter 5 Install USB Cable and Software Chapter 5 Install USB Cable and Software 5.1 Introduce SLC-2080 USB Cable SLC-2080 is a cable that enables the SRC-7000 to connect with a PC. Besides, you can also duplicate the settings in one SRC-7000 and transfer data to another SRC-7000 by this cable. 5.1.1 Install the SLC-2080 USB Driver 1.Locate the SLC-2080 USB driver from the CD enclosed with the package, or download the driver from http://www.sun-wave.com . 2.
SRC-7000 User’s Manual 2. After the program has finished installing the driver, a window will appear as shown below. Click “Finish” to complete the setup processes. The SLC-2080 USB driver is installed completely.
Chapter 5 Install USB Cable and Software 5.2 Install Upgrade Tools The Upgrade Tools enable you to upgrade your firmware and preprogrammed codes through the internet. 1. Locate the program from the CD enclosed with the package or download the program from http://www.sun-wave.com 2. Double click the icon below to install Upgrade Tools, and you will see the window below. Click “Next” to continue. 3. Choose the directory you wish the program to be installed into then click “Next”.
SRC-7000 User’s Manual 4. Choose a Start menu folder for your Upgrade Tools shortcuts then click “Next”. 5. After finishing all steps above, click “Install” to start installing the program.
Chapter 5 Install USB Cable and Software 6. You have now successfully installed Upgrade Tools. Click “Finish” to exit the installation.
SRC-7000 User’s Manual 5.3 Upgrade VMCU Firmware and VMCF Preprogrammed Codes With the SLC-2080 and the Upgrade Tools, you can easily upgrade your SRC-7000 via Internet. There are two types of files you can upgrade: VMCU Firmware and VMCF Pre-programmed Codes. A. VMCU Firmware: This file controls the operation of the SRC-7000. You can load updated VMCU Firmware files to allow your SRC7000 to operate more effectively. B. VMCF Pre-programmed Codes: This file is the database of preprogrammed codes.
Chapter 5 Install USB Cable and Software 3. Select “Data Source” you will load the files from : * From Internet This option will download the latest database files from Internet. The PC needs to be connected with Internet. Please refer to step 4 for following procedure. * From File Select this option will load the data from existing *.vmcu / *.vmcf file. Open the file which you selected and download the data into the remote control. * Backup Remote Select this option will back up your settings.
SRC-7000 User’s Manual 5. There are two choices in “Upgrade type”, “All (Reset to factory default)” and “Pre-programmed code” If you select “All (Reset to factory default)”, you will upgrade your pre-programmed code database and erase all your settings on the SRC-7000 simultaneously. If you select “Pre-programmed code”, you will upgrade your pre-programmed code database and keep your settings on the SRC-7000. 6.
Appendix A Features 64 Devices in One: 64 in 1 remote control, no more running out of device buttons. Customization: Users can customize the size, text or icon for buttons. Pre-Programmed Code: Users can access the specific codes for their devices 69 from pre-programmed codes. Powerful Learning Function: The SRC-7000 is able to copy almost all IR codes by its powerful learning function.
SRC-7000 User’s Manual Specifications Model SRC-7000 Battery 3 x AAA 1.5V Alkaline batteries or Ni-MH rechargeable batteries (not included) Dimensions (WxHxD) 2.7” x 8.3” x 0.9” / 68 x 210 x 24 mm ) Weight 6 oz / 170g (without batteries) Keys 64 Keys / 8 Pages Display Touch liquid crystal display LCD Resolution 160 x 105 black/white dot matrix LCD. LCD Screen (WxH) 1.7” x 2.8” / 4.2.4 x 70.
Appendix B Optional Accessories SLC-2080 USB Cable Transmit Cable The SLC-2080 is an optional USB cable that enables transmission of system setup between a PC and the SRC-7000. With the Transmit Cable, the SRC-7000 also can duplicate the user setup data from one unit to another. RemoteComm: With the “RemoteComm” software, users can customize the remote control text, icon, create macros and setup timers.
Appendix C Troubleshooting Tables Problem Solution LCD does not show anything when you touch it. • • • • Batteries may be dead. Replace the batteries with three new AAA Alkaline batteries. Check the batteries are properly insert with the + - indications. Reset the SRC-7000 by press the reset switch. (P.9 o.) The SRC-7000 doesn’t operate a device. • Make sure that the desired device on the SRC-7000 LCD panel has been selected. Move SRC-7000 closer to the device.
Problem You see an “error” display during operation. Solution • • IR Learning is not successful. • • • • • Macro does not work. • • A key of your existing remote performs two or more functions • • The LCD screen turns off. The touch panel isn’t sensitivity 73 • The key that you pressed has not been taught or input the IR code. Teach the key via learning procedure. (P.37) Do not use the learn function near an incandescent lamp. Memory capacity is full (64 keys for each device.).
