Install Instructions

ManualsBrandsSuntouch ManualsElectric Radiant HeatProMelt PM-5 Detector (120/208/240V)

Limited Warranty: Watts Radiant (the “Company”) warrants each product to be free from defects in material and workmanship under normal usage for a period of one year from the date of original shipment. In

the event of such defects within the warranty period, the Company will, at its option, replace or recondition the product without charge.

THE WARRANTY SET FORTH HEREIN IS GIVEN EXPRESSLY AND IS THE ONLY WARRANTY GIVEN BY THE COMPANY WITH RESPECT TO THE PRODUCT. THE COMPANY MAKES NO OTHER WARRANTIES,

EXPRESS OR IMPLIED. THE COMPANY HEREBY SPECIFICALLY DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

The remedy described in the first paragraph of this warranty shall constitute the sole and exclusive remedy for breach of warranty, and the Company shall not be responsible for any incidental, special or consequen-

tial damages, including without limitation, lost profits or the cost of repairing or replacing other property which is damaged if this product does not work properly, other costs resulting from labor charges, delays,

vandalism, negligence, fouling caused by foreign material, damage from adverse water conditions, chemical, or any other circumstances over which the Company has no control. This warranty shall be invalidated

by any abuse, misuse, misapplication, improper installation or improper maintenance or alteration of the product.

Some States do not allow limitations on how long an implied warranty lasts, and some States do not allow the exclusion or limitation of incidental or consequential damages. Therefore the above limitations may not

apply to you. This Limited Warranty gives you specific legal rights, and you may have other rights that vary from State to State. You should consult applicable state laws to determine your rights. SO FAR AS IS

CONSISTENT WITH APPLICABLE STATE LAW, ANY IMPLIED WARRANTIES THAT MAY NOT BE DISCLAIMED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE, ARE LIMITED IN DURATION TO ONE YEAR FROM THE DATE OF ORIGINAL SHIPMENT.

Product Amp

Rating

Minimum Lead

Wire Gauge

Maximum Allow-

able Distance

0-14 amps 14 ga 50 ft. (15.24 m)

15+ amps 10 ga 50 ft. (15.24 m)

Recommended Switch Settings

Function Trigger LTC DEL RAIN SNOW

Snow sensor

w/o LTC

TT>AT OFF OFF OFF ON

Snow sensor

w/LTC

TT>AT>15°F (9.5°C) ON OFF OFF ON

Snow controller w/o LTC TT>AT OFF ON OFF ON

Snow controller w/LTC TT>AT>15°F (9.5°C) ON ON OFF ON

Do Not set the Rain switch to "ON". Possible overheating

of the snow melt cables may result.

Specifications

Supply Voltage

100 - 120 VAC

200 - 240 VAC

Trigger Temperature

Range (TT)

340F to 440F (10C to 6.50C)

Configuration Modes

Snow Only

Rain Only

Snow or Rain

Delay Settings (post melting) 30 to 90 minutes

Low Temperature

Cutoff (LTC)

Prevents system operation when

Ambient Temperature (AT) is

below 15°F (9.50C)

Operation Modes

Automatic

Standby/Reset

Manual

Sensor Maintenance

At least once every four months the PM 5 should be powered

down and the sensor grid be wiped clean with clear water. Heavy

deposits left behind by evaporated water may be removed by

gently scrubbing with a non-metallic scouring pad.

SNOW

RAIN

DEL

LTC

120 240 120

R2B R1B

R1A

R2A

CONFIGURATION SWITCH

CONTROL/MONITOR JACK

SWITCH JACK

VOLTAGE SELECT

INPUT POWER

LOAD 2

GRID JACK

PROBE JACK

TEMP ADJUST

DELAY ADJUST

LOAD 1

CDP-2

Deice On

Snow Sensor

Control/Display Panel

Standby

Automatic

Manual On

SYSTEMS

AUTOMATED

ENGINEERING

Indoor monitoring

and control of the PM 5

is available with

the optional PM DP

snow melt sensor

remote control.

For more information see

the PM DP submittal or

installation instructions.