Instruction Manual Pulse Oximeter RES5102 Manufactured for Sunset Healthcare Solutions 180 N Michigan Ave Ste 2000 Chicago, IL 60601 IFU-00054 REV 1.
1. Product Introduction and Operation Guide 1.1 Front View Figure 1 Front View of RES5102 1.2 Battery Installation A. Put the two AAA batteries into battery compartment in correct polarities (Figure2). B. Push the battery cover horizontally in the direction of the arrow WARNINGS: • Battery polarities should be correctly installed, otherwise, damage may be caused to the equipment. • Please remove the batteries if the equipment will not be used for a long time.
Figure 2 Battery Installation 1.3 Lanyard installation A. Pass the thinner end of the lanyard through the hanging hole. B. Loop the thicker end of the lanyard through the thinner end and tighten the lanyard (Figure 3).
1.4 Before Operating A. Before use check and confirm that the user’s finger size is appropriate B. Before use check and confirm that the environment contains only non-combustible material, and avoid high or low temperature and humidity. Pay attention to the following: a) Avoid glare and exposure to direct sunlight. b) Avoid infrared radiation or ultraviolet radiation. c) Avoid contact with the organic solvent, mist, dust, corrosive gas. C.
Figure 4 Finger Placement Diagram 1.5 Operation A. Press the bottom of the equipment to open the probe, then insert one finger into the probe. B. Turn on the oximeter by pressing and holding the power button for about 2 seconds. C. After about 8 seconds, the measurement result can be read directly from the display screen. D. Before reading the parameters, make sure that the pulse oximeter numbers have remained stable for more than 4 second. E.
On parameter interface 1 • Move”*” to the corresponding option, and hold the button to set alarm or beep to on or off. • When alarm is set to on and the measured SpO2 or PR Values go beyond the upper limit or lower limit, the oximeter gives off an alert sound. • When alarm is set to off and the measured values go beyond the limit, the Oximeter will not give any alert sound.
Interface 1 Interface 2 Figure 5 The setting interfaces of the oximeter
2. Specification 2.1 Classification Type of protection against electric shock: II (Internally powered equipment) Degree of protection against electric shock: Type BF-Applied part Operating mode : Spot checking Application: Sport use only Degree of protection against hazards of explosion: IP22 2.2 Power Requirements Specification of alkaline batteries: Two AAA (LR03) Operating current: 25-50mA 2.3 Physical Specifications Width*Height*Depth: 57×30×31 mm Weight: 28g (Bare machine) 2.
2.5 Environmental Specifications Temperature Temperature Operating: +50~+104°F / +10~ +40°C Storage/Transportation: -4~+140°F / -20~+60°C Humidity Operating: 15~95%, noncondensing Storage/Transportation: 10~95%, noncondensing Atmosphere Pressure Operating: 70~106kpa Storage/Transportation: 50~107.4kpa 2.6 Display Display Color: 1.3”,Blue Display content: SpO2%, Pulse Rate, PI%, Bar Graph Battery Indicator, Pulse Wave Notes: 1.
3. Maintenance, Cleaning, Disinfection 3.1 Maintenance The equipment’s design life expectancy is about 2 years. Keep equipment and accessories free of dust and dirt, and observe the following rules: A. Please clean the equipment before use according to chapter 6.2. Remove the batteries inside the battery cassette if the equipment will not be operated for a long time. B. Replace the batteries when the battery voltage indicates lamps are empty. C.
3.2 Cleaning Equipment should be cleaned on a regular basis. If there is heavy pollution, dust or sand in its storage environment, it should be cleaned more frequently. Before cleaning the equipment, consult your hospital’s regulations. Recommended cleaning agents are: A. Mild soap (diluted). B. Ethanol (70%). To clean your equipment, follow these rules: A. Shut down the pulse oximeter. B. Clean the display screen using a soft, clean cloth dampened with a glass cleaner. C.
erosive cleaners (such as acetone or acetone-based cleaners). • If you spill liquid onto the equipment, contact your service personnel. 3.3 Disinfection Clean the pulse oximeter before disinfecting it. The recommend disinfectant is ethanol 70%. Disinfection steps are the same as cleaning. CAUTION • Never use ETO or formaldehyde for disinfection. 3.4 Disposal Dispose of the pulse oximeter in accordance with local environment and waste disposal laws and regulations. 4. Accessories One lanyard.
5. Troubleshooting Trouble The equipment can’t be turned on. Possible Reason Solution The battery is depleted or almost depleted. Please replace batteries. The battery installation is incorrect. Install the battery over again. The device is damaged. Please contact product distributor. The finger size is too big or small. Select the suitable size finger to measure. The Spo2 and PR are Excessive ambient not displayed normally light. Aviod excessive ambient light irradiation.
Trouble Possible Reason Solution The finger is not Replace the finger and inserted deep enough. try again. The finger is shaking Try to keep still. or the body is moving. The Spo2 and Pulse Rate are unstable. Device is not being used in environment required by this manual. Please use in normal working environment. The device is damaged. Please contact the product distributor. 6.
3 4 5 6 7 Emissions test RF emissions CISPR 11 RF emissions CISPR 11 Harmonic emissions Compliance Group 1 Class B Not applicable IEC 61000-3-2 Voltage fluctuations Not appli/ flicker cable emissions IEC 61000-3-3 Electromagnetic environment – guidance The Model RES5102 uses RF energy only for its internal function. Therefore, its RF emissions are very low and are not likely to cause any interference in nearby electronic equipment.
Guidance and manufacturer´s declaration – electromagnetic immunity The Model RES5102 is intended for use in the electromagnetic environment specified below. The customer or the user of the Model RES5102 should assure that it is used in such an environment. Immunity test IEC 60601 test Compliance Electromagnetic level level environment guidance ± 8 kV contact ± 8 kV contact Floors should be Electrostatic wood, concrete discharge (ESD) ±2 kV, ±4 kV, ±2 kV, ±4 kV, or ceramic tile.
Voltage dips, short interruptions and voltage variations on power supply input lines 0% UT (100 % dip in UT ) IEC 61000-4-11 0% UT (100% dip in UT ) for 1 cycle at 0° N/A N/A for 0.
Guidance and manufacturer’s declaration – electromagnetic immunity The RES5102 is intended for use in the electromagnetic environment specified below. The customer or the user of the RES5102 should assure that it is used in such an environment.
where P is the maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer and d is the recommended separation distance in metres (m). Field strengths from fixed RF transmitters, as determined by an electromagnetic site survey, a should be less than the compliance level in each frequency range b Interference may occur in the vicinity of equipment marked with the following symbol: NOTE 1 At 80 MHz and 800 MHz, the higher frequency range applies.
A. The ISM (industrial, scientific and medical) bands between 0,15 MHz and 80 MHz are 6,765 MHz to 6,795 MHz; 13,553 MHz to 13,567 MHz; 26,957 MHz to 27,283 MHz; and 40,66 MHz to 40,70 MHz. The amateur radio bands between 0,15 MHz and 80 MHz are 1,8 MHz to 2,0 MHz, 3,5 MHz to 4,0 MHz, 5,3 MHz to 5,4 MHz, 7 MHz to 7,3 MHz, 10,1 MHz to 10,15 MHz, 14 MHz to 14,2 MHz, 18,07 MHz to 18,17 MHz, 21,0 MHz to 21,4 MHz, 24,89 MHz to 24,99 MHz, 28,0 MHz to 29,7 MHz and 50,0 MHz to 54,0 MHz. B.
