SPT Portable Air Conditioner Instruction Manual WA-1240AE1: 12,000BTU (cooling only) WA-1240H1: 12,000BTU (cooling & heating) WA-1420E1: 14,000BTU (cooling only) WA-1420H1: 14,000BTU (cooling & heating) WA-1484E1: 14,000BTU (cooling only) Thank you for purchasing our Portable Air Conditioner. Before using your air conditioner, please read this instruction manual carefully and keep it for future reference.
| Preparation — control panel horizontal louver blade rar fil LA {swing automatically) hind the rile) | PE des) upper air intake upper drain outlet power cord outlet ar outer lower air filter power cord buckle | air intake lower drain outlet (heating models only) power cord buckle power cord outlet power plug socket bottom tray drain outlet Caster front tear
| Safety Precautions Please read through these instructions before you start the installation process. Improper installation can cause damage fo the uni, your personal property, and also poses a personal safety hazard, «= installation must be performed in accordance fo the installation instructions. Improper installation can cause water leakage, electrical shock or fire. = Use only the included accessories, parts and specified tools for installation.
| Cautions « This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge If they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play the appliance. Cleaning and user maintenance shall not be made by children without supervision.
| Installation Choosing The Right Location Recommend Installation linchpin Your installation location should meet the following requirements: NOTE: -Make sure that you install your unit on an even surface to minimize All the illustrations in the manual are for explanation noise and vibration. purpose only. Your machine may be slightly different. -The unit must be installed near a grounded plug, and the Collection The actual shape shall prevail. Tray Drain (found on the back of the uni) must be accessible.
{ Installation Souls Needed -Medium Philips screwdriver; -Tape measure or ruler; -Knife or scissors; -Saw (optional, to shorten window adapter for narrow windows) Your Window Installation Kit fits windows and can be shortened for smaller windows.
| Installation Note: Once the exhaust hose assembly and adjustable slider kit are prepared, choose from one of the following installation methods. Cut the adhesive foam seal A and B strips fo the proper lengths and attach them to the window sash and frame. Insert the slider kit assembly into window opening. If desired, install the security bracket with 2 screws. Cut the non-adhesive foam seal C to match the width of the window.
! Installation Note: It is necessary to purchase the following parts for through-the-wall installation: Wall Adapter {sold separately, please contact Supervention at 1-800-330-0388 or visit Wwww.sunpentown.com) Screws & expansion plugs me 3855 | (can be purchased at any hardware store) 1. Prepare a hole in the wall and install Wall Adapter to the opening (from outside). Secure with 4 expansion plugs and screws. 2. Attach exhaust hose to the Wall Adapter. Cover the hole using the adapter cap when not in use.
| Operation (om Swing button on) Mode button ; S Fan button Used to initiate the Auto swing feature. Selects the appropriate operating mode. Each press of | Controls the fan speed.
| Operation LED display Displays set temperature, in either °C or °F. Displays auto-timer settings (if any) When unit is in DRY or FAN modes, displays current room temperature. Displays error codes and protection codes: E1: Room temperature sensor error E2: Evaporator temperature sensor error E3: Condenser temperature sensor error E4: Display panel communication error P1: Bottom tray is full. Connect the drain hose to drain and empty the bottom tray.
| Operation TIMER function When the unit is operating: Press the TIMER button to program auto-stop, the TIMER OFF indicator will illuminate. Press the + or buttons to set the time for unit to tum off. Press the TIMER button again within 5 seconds will allow you to program auto-start. The TIMER-ON indicator will illuminate. Press the + or buttons to set the time for unit to turn on. When the unit is off: Press the TIMER button to program auto-start, the TIMER ON indicator will illuminate.
| Operation Water drainage Continuous Drainage for DRY mode Continuous drain hose Remove the upper drain plug from back of unit. Attach drain connector (5/8" universal female mender) to a 3/4" hose (not included, purchase locally). Connect to spout. For models without the drain connector, just attach drain hose to spout. Position the open end directly over drain area. Continuous Drainage for HEAT mode (required) (Heating models only) Remove the lower drain plug from the back of the unit.
| Maintenance Sally Precautions -Always unplug the unit before cleaning or servicing. -DO NOT use flammable liquids or chemicals to clean the unit. -DO NOT wash the unit under running water. Doing so causes electrical danger. -DO NOT operate the machine if the power cord is damaged. Contact Supervention or a qualified electrician. Clan the Alr Filter Clean the filters at least once every two weeks to prevent inferior fan operation due to dust accumulation.
| Trouble Shooting Please check the machine according fo the following before asking for maintenance; ele Unit does not turn on when pressing ON/OFF button Unit does not cool well The unit is noisy and vibrates too much Gee P1 Error Code Hi The Water Collection Tray is full. Turn off the unit, drain the water from the Water Collection Tray and restart the unit.
USING THE REMOTE CONTROLLER Battery Required AAA battery x 2 {not included) Sigma! Receiving Range 3m Operating temperature. 5° ~ 80°C (28°F ~140°F) The design and specifications are subject to change without prior notice for product improvement. Consult with the manufacturer for details NOTE: ® Buttons design is based on typical model and might be slightly different from the actual one you purchased, the actual shape shall prevail.
Before you begin using your new air conditioner, make sure to familiarize yourself with the remote control. The following is a brief introduction to the remote control. For detailed instructions on operation of the air conditioner, refer to the Instruction Manual. ON/OFF Tums the unit on or off. MODE Scrolls through modes: AUTO — COOL — DRY ~ HEAT (heating mode! only) — FAN NOTE: Please do not select HEAT mods if your mode! is cooling only type. lH SHORT CUT [Sets and activates your favorite per-settings.
HOT SURE WHAT 4 FUNCTION DOES Refer 1 the Operation Instructions section of his manual for a detailed description on how io use your ai conditioner Button designs on your unit may differ slightly from the example shown When there are wide differences batsmen Remote controller illustration and USER'S MANUAL an function description the description of USER'S MANUAL shall prevail Inserting and Replacing Batteries The remote controller is powered by two AAA batteries {not included).
Transmission indicator Lights up when remote sends signal to unit MODE display ON/OFF display Displays the current Appears when the unit is fumed on, mess, including: and disappears when it is turned off * AUTO y * COOL% TIMER ON display TIMER OFF display s prey O Displays when TIMER Displays when TIMER o HEAT ON is set OFF is set {Heating models only) + FAN Timer On Timer Off Battery display I Low battery CO Auto| Set Temp.
The operating temperature range for the unit is You can increase or decrease the set temperature in increments AUTO OPERATION In AUTO mode, the unit will automatically select COOL, FAN, HEAT (heating models only), or DRY mode based on the set temperature 1. Press the MODE button to select Auto mode. 2. Set your desired temperature using the Temp Up/Down button. 3. Press the ON/OFF button to start the unit. NOTE: FAN SPEED can t be set in Auto mode. ~~ HEAT OPERATION 1. Press the MODE button to select HEAT.
DDG DRY OPERATION FAN OPERATION 1. Press the MODE button to select DRY 1. Press the MODE button to select FAN mode. mode. 2. Press FAN button to select the fan speed: 2. Set your desired temperature using the AUTO, LOW, MED or HIGH. Temp Up/Down button. 3. Press the ON/OFF button to start the unit. 3. Press the ON/OFF button to start the unit. NOTE: Temperature cannot be set in FAN NOTE: FAN SPEED can not be changed in mode. As a result, LCD screen will not DRY mode. display temperature.
Your air conditioning unit has two timer-related functions: TIMER ON: Set the amount of time after which the unit will automatically turn on. TIMER OFF: Set the amount of time after which the unit will automatically turn off. TIMER ON function: Sets amount of time for unit to tum on, such as when you will return home. ® Press the TIMER ON button. By default, the last set time and "h" (hour) will appear on display. ® Press the TIMER ON button again and repeatedly to set desired time.
Setting combined timers: TIMER ON and TIMER OFF at the same Keep in mind that the time periods you set for both functions refer to hours after the current time. For example, say that the current time is 1:00 PM, and you want the unit to turn on automatically at 7:00 PM (which is 6 hours from current time); operate for 2 hours, then automatically turn off at 9:00 PM (which is 8 hours from current time).
Example: Setting the unit to turn on after 6 hours, operate for 2 hours, then turn off {see the figure below).
The SLEEP function is used to conserve energy while you sleep. When activated, unit will increase set temperature by after 30 minutes; and by another after additional 30 minutes. New temperature will be maintained for 7 hours then unit returns fo originally set temperature. This ends the SLEEP function. B @® DOD Used to restore the current settings or resume previous settings.
If this product is defective or not working properly Please DO NOT return to your retail store Please contact us directly with any Service or Technical Assistance Contact us toll free at: 1-800-330-0388
& Your Guarantee If this product is found to be faulty as a result of faulty materials or workmanship within one year from date of purchase, it will be repaired free of charge. This guarantees is subject to the following terms: Supervention must be notified of the fault. Proof of purchase must be presented to Allentown's nominated representative. The warranty will be void if the product is modified, misused or repaired by an unauthorized person.
