- Sunpentown Intl. Inc. Telephone User Manual

ManualsBrandsSunpentown Intl ManualsTelephoneSunpentown Intl. Inc. Telephone FM-8800D/8800S

VHF RADIOTELEPHONE

FM-8800D/8800S

Summary of content (129 pages)

PAGE 1
VHF RADIOTELEPHONE FM-8800D/8800S
PAGE 2
The paper used in this manual is elemental chlorine free. FURUNO Authorized Distributor/Dealer 9-52 Ashihara-cho, Nishinomiya 662-8580, JAPAN Telephone : 0798-65-2111 Fax 0798-65-4200 : All rights reserved. Printed in Japan FIRST EDITION : SEP. 2004 F : FEB. 02, 2007 Pub. No.
PAGE 3
CANCELING DISTRESS ALERT If less than three seconds has elapsed since the [DISTRESS] key was pressed, the distress alert may be canceled by pressing the [CANCEL] key. Otherwise, do the following: 1. Switch off equipment immediately. 2. Switch equipment on and set to Channel 16. 3. Transmit message to “All Stations” giving your vessel's name, callsign and DSC number to cancel the distress alert. Example message: All Stations, All Stations, All Stations This is VESSEL'S NAME, CALLSIGN, DSC NUMBER, POSITION.
PAGE 4
SAFETY INSTRUCTIONS WARNING Do not open the equipment. Hazardous voltage which can cause electrical shock, burn or serious injury exists inside the equipment. Only qualified personnel should work inside the equipment. Do not approach the antenna closer than 0.9 m (MPE by FCC) when it is transmitting. The antenna emits radio waves which can be harmful to the human body. WARNING Do not operate the equipment with wet hands. Electrical shock can result. Keep heater away from equipment.
PAGE 5
Important Notices • No part of this manual may be copied or reproduced without written permission. • If this manual is lost or worn, contact your dealer about replacement. • The contents of this manual and equipment specifications are subject to change without notice. • The example screens (or illustrations) shown in this manual may not match the screens you see on your display. The screen you see depends on your system configuration and equipment settings.
PAGE 6
TABLE OF CONTENTS FOREWORD ....................................................................................................... vii SYSTEM CONFIGURATION................................................................................ ix SPECIFICATIONS........................................................................................... SP-1 1. OPERATIONAL OVERVIEW 1.1 Controls Keys and LCD Indication............................................................................. 1-1 1.1.1 Front panel...
PAGE 7
TABLE OF CONTENTS 3. DSC OPERATION FOR NON-DISTRESS CASES 3.1 Coast or Ship Call ....................................................................................................... 3-1 3.1.1 Sending a coast or ship call.............................................................................. 3-2 3.1.2 Receiving acknowledgement of coast or ship call ............................................ 3-4 3.1.3 Receiving a coast or ship call .................................................................
PAGE 8
5. SYSTEM SETUP 5.1 Displaying Self ID ...........................................................................................................5-1 5.2 Displaying Group ID List.................................................................................................5-1 5.3 Naming Intercom ............................................................................................................5-2 5.4 Displaying Program Version ......................................................................
PAGE 9
FOREWORD A Word to FM-8800D/FM-8800S Owners Congratulations on your choice of the FURUNO FM-8800D/FM-8800S VHF Radiotelephone. We are confident you will see why the FURUNO name has become synonymous with quality and reliability. For over 50 years FURUNO Electric Company has enjoyed an enviable reputation for quality marine electronics equipment. This dedication to excellence is furthered by our extensive global network of agents and dealers.
PAGE 10
FOREWORD Features The FURUNO FM-8800D/FM-8800S is a cost-effective all-in-one marine VHF radio system consisting of a 25 W VHF radiotelephone, a DSC modem, and a CH 70 watch receiver. It complies with GMDSS carriage requirements for safety and general communications. The FM-8800D offers full-duplex voice communications and the FM-8800S offers simplex voice communication on ITU channels in the marine mobile VHF band.
PAGE 11
SYSTEM CONFIGURATION The FM-8800D/FM-8800S is a highly advanced 25 W VHF transceiver with DSC terminal. It is designed to satisfy the stringent requirements of marine communications, and complies with GMDSS carriage requirements for safety and general communications.
PAGE 12
SYSTEM CONFIGURATION This page is intentionally left blank.
PAGE 13
SPECIFICATIONS OF MARINE VHF RADIOTELEPHONE FM-8800D/FM-8800S 1. GENERAL (1) Number of Channels INTL: 57 USA: 55 (57)* Weather: 10 Canada: 55 (57)* INLND-WA: 55 (57)* Private: 20 *: CH75&76 can be included MEMORY CH: 50 for some countries. Within ±1.5 kHz FM-8800S: Simplex/Semi-duplex FM-8800D: Simplex/Full-duplex 16K0G3E (Voice) 16K0G2B (DSC) 50 ohms (2) Frequency Stability (3) Communication System (4) Class of Emission (5) Antenna Impedance 2.
PAGE 14
5. CH70 WATCH RECEIVER (1) Receiving Frequency (2) Sensitivity (3) Conducted Spurious Emission 156.525 MHz Symbol error rate: Less than 1% (at 0 dBμV) Less than 2 nW 6. POWER REQUIREMENTS (1) Power Supply (2) Power Consumption 24 VDC (-10%/+30%) FM-8800S Waiting Receive Transmit FM-8800D Waiting Receive Transmit DUP Transmit 7. DIGITAL INTERFACE 0.5 A 1.6 A at 4 W audio output 1.6 A at 1 W output, 4.7 A at 25 W output 0.5 A 1.6 A at 4 W audio output 2 A at 1 W output, 6 A at 25 W output 3.
PAGE 15
1. OPERATIONAL OVERVIEW The FM-8800D/FM-8800S system consists of a transceiver block and two antennas. The transceiver block contains a VHF transmitter, receiver, and channel 70 watch receiver module. FM-8800D additionally provides a duplexer block. All operations are controlled on its front panel. 1.1 Controls Keys and LCD Indication 1.1.1 Front panel LoundSpeaker Transmits the distress alert. Press this button three seconds continuously. LCD Keep pressed for 4 s in case of DISTRESS.
PAGE 16
1. OPERATIONAL OVERVIEW 1.1.2 Controls The functions of keys of the transceiver unit and the remote station are almost the same. The table below shows the controls and keys for the transceiver unit. Controls Functions • Selects a channel. • Moves the cursor at menu opened. CHANNEL (PUSH TO ENTER) • Register a selected item when pressed. • While pressing down the SHIFT key, adjust the contrast of the display. SQUELCH • Mutes the receiver when no signal is presented on the channel selected.
PAGE 17
1. OPERATIONAL OVERVIEW 1 • Enters 1, ., ,, ”, :, ;, -, +, *, #, entry mode. , (, ), !, $, &, / character at • Turns the loudspeaker on or off. Pressing the SHIFT and then this key turns loudspeaker on or off. In the off state, the loudspeaker icon appears. However, the key click actives and the alarm sounds when a distress or urgent call is activated. 2 ABC 3 TEST • Enters alphanumeric data (2, A, B, C, a, b, c). • Adjusts panel illumination when proceeded by the SHIFT key.
PAGE 18
1. OPERATIONAL OVERVIEW 0 HI/LO ▲ * SHIFT • Enters “0”. • Changes the output power high(25 W) or low(1 W). However, the following channels are always 1 W. INTL mode: CH15, CH17, CH75, CH76 USA mode: CH13, CH15, CH17, CH67 • Press to activate secondary function. • Moves the screen to previous item. • Moves cursor backward for editor field. ▼ • Displays transmitting/receiving messages. LOG • Enters # character at numeric entry mode. # • Moves the screen to next item.
PAGE 19
1. OPERATIONAL OVERVIEW 1.1.3 Indications on the LCD Below are all the indications which appear on the standby display on the transceiver unit. INTL 1 SHIFT 4 Hi 5 Rx 7 6 DUP 14 AUTO ACK * LAT: 34 °45' N LON: 135° 45' E 8 116 SCAN 10WATCH 9 2 CH70 * 10:45 UTC AUTO 13 11 3 12 Standby display on the transceiver unit Reference no. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Meaning Displays the channel mode.
PAGE 20
1. OPERATIONAL OVERVIEW Below are the indications which appear on the standby display on the remote handset. SHIFT INTL Hi Rx SCAN DUP 03 WATCH CH70** LAT: 12 34' N LON: 123 45' E 12:34 UTC AUTO MANUAL ACK** 3* GPS ERROR If you press at the left-hand screen, right-hand screen appears. If you press at the right-hand screen, the left-hand screen appears immediately. The indications are the same as those on of the transceiver unit. The *- marked number is the terminal number of the remote station.
PAGE 21
1.
PAGE 22
1. OPERATIONAL OVERVIEW 1.2.3 Adjusting volume of loudspeaker The VOLUME control adjusts the volume of the loudspeaker. 1.2.4 Adjusting squelch The SQUELCH control adjusts the squelch threshold level. Adjust it so that white noise heard in the loudspeaker just fades out. Perform this operation when no traffic is being received. AUTO squelch automatically reduces white noise. Usually select the AUTO position. Avoid turning the squelch too far clockwise — you may miss a long distance communication.
PAGE 23
1. OPERATIONAL OVERVIEW 1.2.8 Quick selection of CH16 Press the CH16 key to select CH16, the International Calling and Safety Channel. The use is limited to distress, safety and calling. The transmission on CH16 (156.800 MHz) should be limited to within 1 minute except for distress calling. Avoid calling on CH16 for purposes other than distress, urgency and very brief safety communications when another calling channel is available. 1.2.
PAGE 24
1. OPERATIONAL OVERVIEW 1.3 DSC Operational Overview Digital Selective Calling (DSC) is the global calling system adopted by the ITU-R and IMO for selective calling of coast station and ship radio stations. The DSC system is used for both safety and routine calling. The GMDSS requires the use of DSC for distress alerting and safety calls. 1.3.1 LED warnings The LED below the DISTRESS key lights continuously when the distress signal is transmitted.
PAGE 25
1. OPERATIONAL OVERVIEW Preparing and transmitting DSC messages There are two methods by which you can prepare and transmit DSC messages, and they are shown below. ● Preparing message for immediate transmission 1. Press the CALL key at the standby display. 2. Select the call type. 3. Select other party (ID) if necessary. 4. Select the communications category. 5. Select the communications channel. 6. Press the CALL key more than three seconds.
PAGE 26
1. OPERATIONAL OVERVIEW 1.4 Priority If one or more remote stations are installed, the transceiver unit (main unit) has the highest priority. You can interrupt remote station operation at any time with the handset of the main unit. When you hook off the handset of the main unit, “OCCUPIED FM8800” (default. This may be change. See section 5.3) is indicated on all remote stations. Each remote station has its own priority. The remote station ID (1-4) indicates its priority.
PAGE 27
2. DSC DISTRESS COMMUNICATION 2.1 Distress Alert Transmission from the DISTRESS Key If a distress situation occurs, do as follows: 1. Open the DISTRESS key cover and press the DISTRESS key more than three seconds. The alarm sounds and the red lamp in the key blinks. The lamp will light steadily three seconds later and at the same time the distress alert is transmitted for three seconds. The screen changes as follows.
PAGE 28
2. DSC DISTRESS COMMUNICATION 3) The screen changes to “distress acknowledge (DIST ACK) waiting” display. In this condition, distress communication with CH16 may be possible. ** Compose Message ** CALL TYPE: DISTRESS NATURE: UNDESIGNATED POS : 12 ° 34’N 123 ° 45’E AT : 12 : 34 Waiting for distress acknowledgement. CH16 Now available. TIME TO GO : 4M 12S 4) When the DIST ACK is received, Distress acknowledge received.
PAGE 29
2. DSC DISTRESS COMMUNICATION 3. Press the ENT key. The standby display with CH16 and Hi appears. 4. Provide the following information to the coast station, using a handset on the transceiver unit or remote stations (if connected): Distress communication (1) Press the PTT switch and speak slowly and distinctly, “MAYDAY, MAYDAY, MAYDAY,” pronounced as the French expression “m’aider.” (2) This is; "the name of your vessel and call sign" three times.
PAGE 30
2. DSC DISTRESS COMMUNICATION 2. Rotate the channel knob to choose the nature of distress. On the remote handset, press the up or down arrow key. S Sinking UNDESIGNATED Disabled & Adr Fire Abandoning Flooding Piracy Collision Man over board Grounding T Listing 3. Press the ENT key. The screen changes as follows.
PAGE 31
2. DSC DISTRESS COMMUNICATION 2.3 Distress Alert Transmission from CALL Key You can transmit the distress alert with nature of distress by using CALL key. 1. Press the CALL key. ** Compose Message ** CALL TYPE : COAST CALL TO : COAST AAA COAST ID : 003456789 ROUTINE TCmd1 : SIMPLEX TP TCmd2 : NO INFO CH : 12 Transceiver unit screen * Compose message * CALL TYPE : COAST CALL T Remote handset screen 2. Press the ENT key to show the call type selection window.
PAGE 32
2. DSC DISTRESS COMMUNICATION 5. Rotate the CH knob (or press up / down arrow key) to choose nature of distress and press the ENT key. ** Compose Message ** CALL TYPE : DISTRESS NATURE : Abandoning POS : 12 ° 34’N 123 ° 45’E AT : 12 : 34 SIMP TP 6. Press the ENT key to show the position setup window. INPUT TYPE : AUTO LAT : 34 ° 41’N LON : 134 ° 30’E TIME : 08 : 00 If a position fixing device is not connected, press the ENT key, choose Manual and enter your position.
PAGE 33
2. DSC DISTRESS COMMUNICATION 2.5 Receiving Distress Alert from Other Vessel, Transmitting DIST ACK Signal In no case is a ship permitted to transmit a DSC distress relay call upon receipt of a DSC distress alert on VHF channel 70. Procedure when in area A1 1. When the FM-8800D/8800S receives a distress alert from another vessel, the ALARM LED (red) blinks and the FM-8800D/8800S sounds the distress alarm. 2. Silence the alarm by pressing the CANCEL key. 3.
PAGE 34
2. DSC DISTRESS COMMUNICATION Flow chart for determining if you should/should not transmit DIST ACK signal DSC Distress alert received. Press [CANCEL] key to silence alarm. Listen on CH16 for 5 minutes. Did you receive acknowledge from CS and/or RCC? No Is distress traffic in progress? Yes Yes Is own vessel able to assist? No CS = Coast Station RCC = Rescue Co-ordination Center Enter details in log.
PAGE 35
2. DSC DISTRESS COMMUNICATION Transmitting DIST ACK over CH16 Select VHF CH16 and transmit DIST ACK to vessel in distress. Reply received No reply Transmit DIST ACK to vessel in distress over DSC CH70. Communicate with vessel in distress. Relay the distress alert to a coast station over DSC. Follow the instructions of the coast station. Begin search and rescue operation for the vessel in distress.
PAGE 36
2. DSC DISTRESS COMMUNICATION 1. Press the CANCEL or ENT key to silence the alarm. The following message appears. ** Received Message ** MAY10/’04 08:03 ECC : OK DISTRESS ID IN DIST : 123456789 NATURE : UNDESIGNATED POS : 12 ° 34’N 123 ° 45’E AT : 12 : 34 SIMP TP PRESS ENT TO ACK 2.
PAGE 37
2. DSC DISTRESS COMMUNICATION 2.6 Sending Distress Relay on Behalf of a Ship in Distress When you should relay a distress alert You may relay a distress alert in the following conditions: 1) When the station in distress is not itself in a position to transmit the distress message, or 2) When the master or person responsible for the vessel not in distress, or the person responsible for the coast station, considers that further help is necessary.
PAGE 38
2. DSC DISTRESS COMMUNICATION 4. Press the ENT key. ** Compose Message ** CALL TYPE : RELAY SEL COAST ID : 00 ID IN DIST : NO INFO TCmd : DISTRESS RELAY NATURE : UNDESIGNATED POS : 12 ° 34’N 123 ° 45’E AT : 12 : 34 SIMP TP 5. Press the ENT key again. The COAST ID entry window appears. 6. Key in a coast station ID with numeric keys and press the ENT key. 7. Press the ENT key again. The ID IN DIST entry window appears. 8. Key in the ID number of ship in distress with numeric keys and press the ENT key.
PAGE 39
2. DSC DISTRESS COMMUNICATION 12. Press the CALL key more than three seconds to transmit the distress relay. ** Compose Message ** CALL TYPE : RELAY SEL COAST ID : 003456789 ID IN DIST : NO INFO TCmd : DISTRESS RELAY NATURE : UNDESIGNATED POS : 12 ° 34’N 123 ° 45’E AT : 12 : 34 SIMP TP When CALL key is pressed, this message appears and timer counts down. KEEP PRESSED FOR 3S The message will be transmitted and “Waiting for acknowledgement” will appear. 2.6.2 Sending distress relay to all ships 1.
PAGE 40
2. DSC DISTRESS COMMUNICATION 4. Press the ENT key. ** Compose Message ** CALL TYPE : RELAY ALL ID IN DIST : NO INFO TCmd : DISTRESS RELAY NATURE : UNDESIGNATED POS : 12 ° 34’N 123 ° 45’E AT : 12 : 34 SIMP TP 5. Press the ENT key again. The ID IN DIST entry window appears. 6. Key in the ID number of ship in distress with numeric keys and press the ENT key. If you do not know the ID, simply press the ENT key without entering ID; NO INFO is displayed. 7.
PAGE 41
2. DSC DISTRESS COMMUNICATION 10. Press the CALL key to transmit the call. ** Compose Message ** CALL TYPE : RELAY ALL ID IN DIST : NO INFO TCmd : DISTRESS RELAY NATURE : UNDESIGNATED POS : 12 ° 34’N 123 ° 45’E AT : 12 : 34 SIMP TP KEEP PRESSED FOR 3S When CALL key is pressed, this message appears and timer counts down. After the call is transmitted, the standby display appears. 2.7 Receiving Distress Relay 2.7.
PAGE 42
2. DSC DISTRESS COMMUNICATION 2. Press the CANCEL key or ENT key to silence the alarm and the display changes as below. * Received Message * APR01/ 04 12 : 34 ECC : OK DISTRESS RELAY ALL FROM : 123456789 ID IN DIST : 234567890 TCmd : DISTRESS RELAY NATURE : UNDESIGNATED POS : 12 ° 34’N 123 ° 45’E AT : 12 : 34 SIMP TP PRESS ENT 3. Press the ENT key to return to the standby display with CH16. 4. Watch CH16. 2.7.
PAGE 43
2. DSC DISTRESS COMMUNICATION 2. Press the CANCEL key to silence the alarm and the display changes as below. ** Received Message ** APR01/ 04 12 : 34 ECC : OK DISTRESS RELAY ALL FROM : 003456789 ID IN DIST : 123456789 TCmd : DISTRESS RELAY NATURE : UNDESIGNATED POS : 12 ° 34’N 123 ° 45’E AT : 12 : 34 SIMP TP PRESS ENT 3. Press the ENT key to return to the standby display with CH16. 4. Watch CH16.
PAGE 44
2. DSC DISTRESS COMMUNICATION This page is intentionally left blank.
PAGE 45
3. DSC OPERATION FOR NON-DISTRESS CASES 3.1 Coast or Ship Call The coast or ship call is for sending message to a specific coast or ship station. After transmitting message (called ACK RQ transmission), wait to receive the acknowledge back (ACK BQ) signal from the receiving station. You should receive it within five minutes.
PAGE 46
3. DSC OPERATION FOR NON-DISTRESS CASES 3.1.1 Sending a coast or ship call 1. Press the CALL key. The display changes from the standby display to the COMPOSE MESSAGE screen and the CALL TYPE is displayed in reverse video. ** Compose Message ** CALL TYPE : COAST CALL TO : COAST AAA*1 COAST ID : 003456789 ROUTINE TCmd1 : SIMPLEX TP TCmd2 : NO INFO CH : 12 * Compose message * CALL TYPE : COAST CALL T *1: If the coast or ship ID is registered in FILE, the registered name is displayed.
PAGE 47
3. DSC OPERATION FOR NON-DISTRESS CASES 9. Choose SIMPLEX TP, DUPLEX TP, DATA or FAX as appropriate followed by pressing the ENT key. If you chose SIMPLEX, DUPLEX or FAX, NO INFO appears in the Tcmd2 field. Go to step 12. If you chose DATA, go to the next step. 10. TCmd2 is selected; press the ENT key. V. V. V. V. T V. S V. 26 ter 21 22 22 bis 23 26 bis V. 27 ter V. 32 11. Choose the data type and press the ENT key. 12. Choose CH and press the ENT key. The following window appears.
PAGE 48
3. DSC OPERATION FOR NON-DISTRESS CASES 3.1.2 Receiving acknowledgement of coast or ship call 1. After a coast or ship call is sent, the equipment waits for acknowledgement of the call, showing the display below. Waiting for acknowledgement. COAST ID : 003456789 ROUTINE TCmd1 : SIMPLEX TP TCmd2 : NO INFO CH : 12 TIME TO GO : 3M30 S The timer starts counting down the maximum time to wait for acknowledgement, five minutes. 2. One of the following three messages appears.
PAGE 49
3. DSC OPERATION FOR NON-DISTRESS CASES Able acknowledge call received a) The audio alarm sounds; press the CANCEL key to silence it, and the display changes as below. ** Received Message ** APR01/ 04 12 : 34 ECC : OK COAST ACK FROM : 003456789 ROUTINE TCmd1 : SIMPLEX TP TCmd2 : NO INFO CH : 12 If a file is registered, its registered name is displayed instead of ID. PRESS ENT b) Press the ENT key to go to the standby display. The working channel is automatically set; you may start voice communications.
PAGE 50
3. DSC OPERATION FOR NON-DISTRESS CASES Acknowledging the call automatically or manually by doing one of the following: 1) Send automatic acknowledge (ACK BQ) with comply status “ABLE.” See the procedure below. 2) Sending automatic acknowledge (ACK BQ) with comply status "UNABLE." See the procedure on page 3-7. 3) Manually acknowledging individual call with "ABLE." See the procedure on page 3-8. 4) Manually acknowledging a coast or ship call with "UNABLE.
PAGE 51
3. DSC OPERATION FOR NON-DISTRESS CASES 2) Sending automatic acknowledge (ACK BQ) with comply status "UNABLE." 1. When the automatic acknowledge feature is active (AUTO ACK), the comply status is "UNABLE" and a coast or ship call is received, the display shown below appears, indicating that the auto acknowledge call with UNABLE (ACK BQ) has been sent. The alarm sounds and the ALARM LED blinks two minutes. Unable acknowledge transmitted. ROUTINE TCmd1 : UNABLE TCmd2 : BUSY CH : NO INFO CANCEL ALARM 2.
PAGE 52
3. DSC OPERATION FOR NON-DISTRESS CASES 3) Manually acknowledging individual call with "ABLE." 1. When the equipment is set up with manual acknowledge (MANUAL ACK), the comply status is "ABLE" and a coast or ship call is received, the alarm sounds and the display looks like the one below. Individual request call received. FROM : 123456789 ROUTINE TCmd1 : SIMPLEX TP TCmd2 : NO INFO CH : 08 CANCEL ALARM 2. Press the CANCEL key to silence the alarm. The following display appears.
PAGE 53
3. DSC OPERATION FOR NON-DISTRESS CASES 4. Choose ABLE and press the ENT key. The display changes as shown below. ** Send Message ** SHIP ACK TO : 123456789 ROUTINE TCmd1 : SIMPLEX TP TCmd2 : NO INFO CH : 08 PRESS CALL TO SEND 5. Press the CALL key more than three seconds to transmit the ACK BQ. The display changes to the standby display with a channel specified. 4) Manually acknowledging a coast or ship call with "UNABLE." 1.
PAGE 54
3. DSC OPERATION FOR NON-DISTRESS CASES 3. To send the ACK BQ manually, press the ENT key. The pop-up window shown below is displayed. ABLE UNABLE 4. Choose UNABLE and press the ENT key. The following pop-up screen appears. NO REASON BUSY EQUIP DISBLD MODE UNAVAIL CH UNAVAIL 5. Press the ENT key. ** Send Message ** SHIP ACK TO : 123456789 ROUTINE TCmd1 : UNABLE TCmd2 : NO REASON CH : NO INFO PRESS CALL TO SEND 6. Press the CALL key more than three seconds to transmit the ACK BQ.
PAGE 55
3. DSC OPERATION FOR NON-DISTRESS CASES 2. Press the ENT key to open the call type list. G COAST CALL SHIP CALL GROUP CALL PSTN CALL ALL SHIPS AREA CALL POSITION F POLLING NEUTRAL MEDICAL RELAY ALL RELAY SEL DISTRESS 3. Rotate the CH knob (or press up / down arrow key) to choose GROUP CALL and press the ENT key. 4. GROUP ID is selected; press the ENT key. 5. Key in a group ID and press the ENT key. 6. ROUTINE is selected; press the ENT key. ROUTINE BUSINESS SAFETY URGENCY DISTRESS 7.
PAGE 56
3. DSC OPERATION FOR NON-DISTRESS CASES 13. Choose SELECT CH or NO INFO as appropriate followed by pressing the ENT key. If you chose SELECT CH, the following channel list appears. (The example shown is the international, duplex channel list.) Rotate the CH knob (or press up / down arrow key) to choose a channel you wish to communicate and press the ENT key. DUP CHANNEL 01 02 03 04 05 07 18 19 20 21 22 23 24 25 26 27 28 60 61 62 63 64 65 66 78 79 80 81 82 83 84 85 86 14.
PAGE 57
3. DSC OPERATION FOR NON-DISTRESS CASES 3.3 PSTN Call The PSTN call allows the making and receiving of telephone calls over public switched telephone networks. To use the PSTN call feature, use a handset which has a HOOK ON/OFF function. The standard supply handset has this feature. 3.3.1 Sending a PSTN call 1. Press the CALL key. The display changes from standby display to the COMPOSE MESSAGE screen and the CALL TYPE is displayed in reverse video. 2. Press the ENT key to open the call type list.
PAGE 58
3. DSC OPERATION FOR NON-DISTRESS CASES If a response from the coast station is received within five seconds, transmit PSTN CALL (EOS) signal and then carrier frequency during two seconds. Then your phone rings. Press the CANCEL key to stop the calling sound and change to standby display. Hook off and communicate with other party. Note: If using a hand-microphone, pressing the CANCEL key is equal to off-hook. 3.3.2 PSTN call disconnection (ship disconnects line) 1.
PAGE 59
3. DSC OPERATION FOR NON-DISTRESS CASES 3.3.3 PSTN call disconnection (coast station disconnects line) 1. The PSTN line is disconnected by the coast station when it finds no evidence of communications or the land subscriber hangs up. The coast station then sends charge information as below. PSTN end of call received. FROM : 003456789 TCmd1 : END CALL TCmd2 : NO INFO TEL : 1234567890123456 CHARGE TIME : 00h06m18s PRESS ENT 3.3.4 Receiving a PSTN call 1.
PAGE 60
3. DSC OPERATION FOR NON-DISTRESS CASES 3.4 All Ships Call When an urgent but not life-endangering situation arises on your ship, for example, engine trouble, send an all ships call to request assistance. After sending the call, you can communicate by voice over the radiotelephone. Do the following before beginning actual communications: URGENCY priority: Say PAN three times followed by your call sign. SAFETY priority: Say SECURITE three times followed by your call sign. Coast Station Own Ship 3.4.
PAGE 61
3. DSC OPERATION FOR NON-DISTRESS CASES 7. Choose SIMPLEX TP, DUPLEX TP, DATA or FAX as appropriate followed by pressing the ENT key. If you chose SIMPLEX, DUPLEX, or FAX, the NO INFO appears in the Tcmd2 field. Go to the step 10. If you chose DATA, go to the next step. 8. TCmd2 is selected; press the ENT key. V. V. V. V. T V. S V. 26 ter 21 22 22 bis 23 26 bis V. 27 ter V. 32 9. Choose the data type and press the ENT key. 10. Choose CH and press the ENT key. The following window appears.
PAGE 62
3. DSC OPERATION FOR NON-DISTRESS CASES 3.4.2 Receiving an all ships call In case of ON HOOK 1. When an all ships call is received, the audio alarm sounds and the display looks something like the one shown below. All ships call received. FROM : 123456789 SAFETY TCmd1 : SIMPLEX TP TCmd2 : NO INFO CH : 16 CANCEL ALARM 2. Press the CANCEL or ENT key to silence the alarm. The display changes as follows.
PAGE 63
3. DSC OPERATION FOR NON-DISTRESS CASES 3.5 Geographical Area Call The geographical area call is for sending a call to all ships within the area you designate in your geographical area call. In the figure below, for example, the call will be sent to all ships within 24-34°N, 135-140°W. Reference point (For example, 34°N 140°W) 34°N 10° 24°N 140°W 3.5.1 5° 135°W Sending a geographical area call 1. Press the CALL key.
PAGE 64
3. DSC OPERATION FOR NON-DISTRESS CASES 8. TCmd1 is selected; press the ENT key. 9. Choose SIMPLEX TP, DUPLEX TP, DATA or FAX as appropriate followed by pressing the ENT key. If you chose SIMPLEX, DUPLEX, or FAX, NO INFO appears in the Tcmd2 field. Go to step 12. If you chose DATA, go to the next step. 10. TCmd2 is selected; press the ENT key. V. V. V. V. T V. S V. 26 ter 21 22 22 bis 23 26 bis V. 27 ter V. 32 11. Choose the data type and press the ENT key. 12.
PAGE 65
3. DSC OPERATION FOR NON-DISTRESS CASES 3.5.2 Receiving a geographical area call 1. When a geographical area call is received, the alarm sounds and the ALARM LED blinks two minutes. Geographical area call received. FROM : 123456789 AREA : 12 ° N 123 ° E ↓ 01 ° → 01 ° ROUTINE TCmd1 : SIMPLEX TP TCmd2 : NO INFO CH : 10 CANCEL ALARM 2. Press the CANCEL key to silence the alarm. The following display appears.
PAGE 66
3. DSC OPERATION FOR NON-DISTRESS CASES 3.6 Position Call There are two types of position calls: other station requires your ship's position and your ship requests position of another ship. Finding position of other station Sending own ship's position to other station Other Station Own Station 3.6.1 Position call: requesting other ship's position 1. Press the CALL key. The display changes from standby display to the COMPOSE MESSAGE screen and the CALL TYPE is displayed in reverse video. 2.
PAGE 67
3. DSC OPERATION FOR NON-DISTRESS CASES 8. Press the CALL key more than three seconds to transmit position request. The following display appears. The timer counts down until a response is received. Waiting for acknowledgement. SHIP ID : 123456789 ROUTINE TCmd1 : POSITION REQUEST TCmd2 : NO INFO If a file is registered, its registration name is displayed. If not, this field is blank. TIME TO GO : 3M30 S 9. When an acknowledge call is received, the following display appears and the audio alarm sounds.
PAGE 68
3. DSC OPERATION FOR NON-DISTRESS CASES 3.6.2 Position call: other ship requests your position You may turn automatic acknowledge of position request on or off with POSITION CALL in the system setup menu. For further details, see page 4-3. Automatic reply 1. When another ship requests your position, the status of the 5 ACK key is AUTO ACK and the setting of POSITION CALL on the system setup menu is ON, the FM-8800D/S transmits own position data, showing the display below. Position auto ack transmitted.
PAGE 69
3. DSC OPERATION FOR NON-DISTRESS CASES 2. Press the CANCEL key to silence the alarm. ** Received Message ** APR01/ 04 12 : 34 POSITION CALL FROM : 123456789 ROUTINE TCmd1 : POSITION TCmd2 : NO INFO ECC : OK PRESS ENT TO ACK. 3. To send your position manually, press the ENT key. The following pop-up menu appears. ANSWER NO ANSWER 4. Choose ANSWER by the CH knob and press the CALL key to send your position data. Then, the standby display appears.
PAGE 70
3. DSC OPERATION FOR NON-DISTRESS CASES 3. Rotate the CH knob (or press up / down arrow key) to choose POLLING and press the ENT key. ** Compose Message ** CALL TYPE : POLLING SHIP ID : ROUTINE TCmd1 : POLLING TCmd2 : NO INFO 4. SHIP ID is selected; press the ENT key. 5. Key in a station ID with the numeric keys and press the ENT key. 6. ROUTINE is selected; press the ENT key. ROUTINE BUSINESS SAFETY URGENCY DISTRESS 7.
PAGE 71
3. DSC OPERATION FOR NON-DISTRESS CASES 9-2. When "No response! Try calling again?" is displayed, do one of the following: Re-send call: Push the ENT key followed by the CALL key. Cancel call: Press the CANCEL key to return to the standby display. 3.7.2 Receiving a polling call Automatic reply 1.
PAGE 72
3. DSC OPERATION FOR NON-DISTRESS CASES Manual reply 1. When a polling request call is received and the setting of POLLING CALL on the system setup menu is OFF, the display changes as shown in the illustration below and the audio alarm sounds. Position request call received. FROM : 123456789 ROUTINE TCmd1 : POLLING TCmd2 : NO INFO CANCEL ALARM 2. Press the CANCEL key to silence the alarm. The display changes as below.
PAGE 73
3. DSC OPERATION FOR NON-DISTRESS CASES 3.8 Neutral Craft Call The neutral craft call, which contains own ship position and ID, informs all ships that your ship is not a participant in armed conflict. Send the call BEFORE entering an area of armed conflict. 3.8.1 Sending a neutral craft call 1. Press the CALL key. The display changes from the standby display to the COMPOSE MESSAGE screen and the CALL TYPE is displayed in reverse video. 2. Press the ENT key to open the call type list. 3.
PAGE 74
3. DSC OPERATION FOR NON-DISTRESS CASES 2. Press the CANCEL or ENT key. The audible alarm is silenced and the display changes as below. ** Received Message ** APR01/ 04 12 : 34 ECC : OK NEUTRAL CALL FROM : 123456789 SAFETY TCmd1 : SIMPLEX TP TCmd2 : NEUTRAL CRAFT CH : 16 PRESS ENT TO CHANGE CH 3. Press the ENT key. The display changes to the standby display, indicating CH16. 3.
PAGE 75
3. DSC OPERATION FOR NON-DISTRESS CASES 3.9.2 Receiving a medical transport call 1. When a medical call is received, the alarm sounds and the display changes as below. Medical call received. FROM : 123456789 URGENCY TCmd1 : SIMPLEX TP TCmd2 : MEDICAL CH : 16 CANCEL ALARM 2. Press the CANCEL or ENT key. The audible alarm stops and the display changes as below.
PAGE 76
3. DSC OPERATION FOR NON-DISTRESS CASES 3.10 Log File Three log files are provided for storage of calls: received ordinary log, received distress log and transmitted log. Each log file stores 50 calls, on a first-in, first-out basis. This means that the latest call is saved as log no.1 and the log no. of all previous calls in that log increments by one. When the storage capacity is exceeded, the oldest call is deleted to make room for the latest. A letter mark shows unread or unacknowledged calls.
PAGE 77
3. DSC OPERATION FOR NON-DISTRESS CASES 4. Press the ENT key to open the message. Below is a sample message. ** Received Message ** APR 10/’04 18:30 ECC : OK SHIP CALL FROM : 123456789 ROUTINE TCmd1 : SIMPLEX TP TCmd2 : NO INFO CH : 16 T DELETE T ANSWER For a received message which requires a reply, ANSWER is displayed (for 4.5 minutes). To reply choose it and press the ENT key. 5. Press ▲ or ▼ key to open previous or next page on the log. 6.
PAGE 78
3. DSC OPERATION FOR NON-DISTRESS CASES This page is intentionally left blank.
PAGE 79
4. BASIC SETUP 4.1 Alarm Setup This section provides the procedures for setting up various alarms. The alarm menu enables/disables internal and external alarms. Note that the Distress/Urgency alarm cannot be disabled. Old position alarm in manual position entry mode This alerts the operator when manually entered position data is older by the number of hours or minutes set. 1. Press the MENU key.
PAGE 80
4. BASIC SETUP To set type of alarm to output 1. Rotate the CH knob (or press up / down arrow key) to choose EXT ALARM from the ALARM MENU and press the ENT key. The following setting window appears. DIST/URG : ON SAFETY : OFF ROUTINE : ON Aleays ON 2. Rotate the CH knob (or press up / down arrow key) to choose an appropriate option. Alarm is output to external device. DSTRS/URG: Distress or urgency call output upon receipt. SAFETY: Safety call output upon receipt.
PAGE 81
4. BASIC SETUP 4.2 Auto ACK Setup The Auto Ack Menu enables/disables automatic acknowledgement of ship, coast, position and polling calls. Comply status Set of [5 ACQ] AUTO ACK MANUAL ACK ABLE UNABLE Can send acknowledge automatically. Can send acknowledge manually Can send UNABLE automatically. Can send UNABLE manually. To set COMPLY TYPE 1. Press the MENU key. 2. Rotate the CH knob (or press up / down arrow key) to choose AUTO ACK and press the ENT key. The following menu appears.
PAGE 82
4. BASIC SETUP To set reason for unable If you have chosen UNABLE as the COMPLY STATUS, set the reason as follows: 1. Rotate the CH knob (or press up / down arrow key) to choose UNABLE REASON from the AUTO ACK MENU and press the ENT key. The following menu appears. NO REASON BUSY EQUIP DISBLD MODE UNAVAIL CH UNAVAIL 2. Rotate the CH knob (or press up / down arrow key) to choose a reason for UNABLE. 3. Press the ENT key. Note: This menu is the same as manual acknowledgement.
PAGE 83
4. BASIC SETUP 4.3 Erasing Logs Erasing received ordinary log 1. Press the MENU key. 2. Rotate the CH knob (or press up / down arrow key) to choose the ERASE LOG and press the ENT key. The following window appears. *** ERASE LOG MENU *** RCVD ORDINARY RCVD DISTRESS TRANSMITTED 3. RCVD ORDINARY is selected; press the ENT key to erase the received ordinary log. 4. Choose YES and press the ENT key to erase the received ordinary log. Erasing received distress log 1. Press the MENU key. 2.
PAGE 84
4. BASIC SETUP 4.4 Memory Channel Setup You can save up to 50 channels as follows. 1. Press the MENU key. 2. Rotate the CH knob (or press up / down arrow key) to choose MEMORY CHANNEL and press the ENT key. * Memory Channel 1/7* 01 CH-02 : CH-03 : CH-04 : CH-05 : CH-06 : CH-07 : CH-T 08 : CH-- --------------------------------------------------------- 3. Rotate the CH knob (or press up / down arrow key) to choose a vacant CH number and press the ENT key.
PAGE 85
4. BASIC SETUP 4.5 Message File Entry In this section you will learn how to prepare and store ship, coast, PSTN, group, and area calls for future transmission. 100 calls can be stored. 1. At the standby display, press the MENU key to open the SETUP MENU. **** SETUP MENU **** ALARM AUTO ACK ERASE LOG MEMORY CHANNEL T MESSAGE FILE ENTRY 2. Rotate the CH knob (or press up / down arrow key) to choose MESSAGE FILE ENTRY and press the ENT key. * MESSAGE FILE 1/13 * 1: 2: 3: 4: 5: 6: 7: T 8: 3.
PAGE 86
4. BASIC SETUP 4. Rotate the CH knob to choose the call type and press the ENT key. One of the following display appears depending on the call type selected above.
PAGE 87
4. BASIC SETUP 5. Press the ENT key and key in each ID or AREA followed by the ENT key. To enter area 1: N/E 2: S/W -- ° N --- ° E ↓ -- ° → -- ° a) Enter latitude (degrees) and 1 for north or 2 for south of reference point. b) Enter longitude (degrees) and 1 for east or 2 for west. c) Enter southerly degrees of area. d) Enter easterly degrees of area. e) Press the ENT key. 6. TCmd1 is selected; press the ENT key. 7.
PAGE 88
4. BASIC SETUP 12. Choose a channel with the CH knob (or up / down arrow key) and press the ENT key. 13. Press the ENT key to open the name entry window. 14. Enter a name with the alphanumeric keys. To change a digit, rotate the CH knob. Press the ENT key. '( ) '( !" #$ # !% && 15. REGIST is selected; press the ENT key to register.
PAGE 89
4. BASIC SETUP Position Setup This is where you enter your position, automatically or manually. 1. Press the MENU key at the standby display. 2. Rotate the CH knob (or press up / down arrow key) to choose POSITION from the second page of the main menu. **** SETUP MENU **** T 4.6 POSITION PRINT OUT VOLUME SYSTEM 3. Press the ENT key. The following menu appears. INPUT TYPE: AUTO LAT : -- ° --’LON : --- ° --’TIME : -- : -4. INPUT TYPE is selected; press the ENT key. The following setting window appears.
PAGE 90
4. BASIC SETUP 4.7 Print Out Setup The PRINT MENU enables/disables automatic printing of all transmitted and received calls and the results of the daily test. 1. Press the MENU key at the standby display to open menu. 2. Rotate the CH knob (or press up / down arrow key) to choose PRINT OUT from the second page of the main menu and press the ENT key. **** PRINT MENU **** XMTD CALL MANUAL RCVD CALL MANUAL DAILY TEST MANUAL 3.
PAGE 91
4. BASIC SETUP Volume Setup The VOLUME menu enables/disables key beep (acknowledges correct key input) and adjusts the volume of the earpiece, intercom and off-hook loudspeaker. 1. Press the MENU key at the standby display. 2. Rotate the CH knob (or press up / down arrow key) to choose VOLUME and press the ENT key. **** VOLUME MENU **** KEY CLICK EARPIECE LEVEL INTERCOM VOLUME OFF HOOK SPKR 8 9 8 ON Follow the appropriate procedure to adjust volume of desired item. Key click 1.
PAGE 92
4. BASIC SETUP Intercom volume 1. Choose INTERCOM VOLUME and press the ENT key. INTERCOM SETUP LEVEL (1-16) < < 8 EXT: ENT 2. Rotate the CH knob (or press up / down arrow key) to set the intercom volume level. The setting range is 1 to 16. 3. Press the ENT key. Off-hook loudspeaker You can set the loudspeaker(s) (internal and external) on or off, according to off-hook condition. 1. Choose OFFHOOK SPKR and press the ENT key. 2. Choose ON or OFF and press the ENT key.
PAGE 93
5. SYSTEM SETUP 5.1 Displaying Self ID 1. Press the MENU key. ALARM AUTO ACK ERASE LOG MEMORY CHANNEL T MESSAGE FILE ENTRY **** SETUP MENU **** T **** SETUP MENU **** POSITION PRINT OUT VOLUME TEST SYSTEM 2. Rotate the CH knob (or press up / down arrow key) to choose SYSTEM from page 2 of the menu and press the ENT key. The following window appears. The self ID is displayed on the first line.
PAGE 94
5. SYSTEM SETUP 5.3 Naming Intercom 1. Press the MENU key. **** SETUP MENU **** **** SETUP MENU **** ALARM AUTO ACK ERASE LOG MEMORY CHANNEL T MESSAGE FILE ENTRY POSITION PRINT OUT VOLUME TEST SYSTEM T 2. Rotate the CH knob (or press up / down arrow key) to choose SYSTEM from page 2 of the menu and press the ENT key. The following window appears. * SYSTEM SETUP MENU * SELF ID --------------------GROUP ID LIST INTERCOM NAMING PROGRAM VERSION 3.
PAGE 95
5. SYSTEM SETUP Displaying Program Version 1. Press the MENU key **** SETUP MENU **** ALARM AUTO ACK ERASE LOG MEMORY CHANNEL T MESSAGE FILE ENTRY **** SETUP MENU **** T 5.4 POSITION PRINT OUT VOLUME TEST SYSTEM 2. Rotate the CH knob to choose the SYSTEM and press the ENT key. The following window appears. * SYSTEM SETUP MENU * SELF ID ------------------GROUP ID LIST INTERCOM NAMING PROGRAM VERSION 3. Rotate the CH knob to choose PROGRAM VERSION and press the ENT key to show program version number.
PAGE 96
5. SYSTEM SETUP This page is intentionally left blank.
PAGE 97
6. MAINTENANCE & TROUBLESHOOTING WARNING Do not open the equipment. Hazardous voltage which can cause electrical shock, burn or serious injury exists inside the equipment. Do not work inside the equipment unless familiar with electrical circuits. 6.1 Maintenance Periodic checks 1) 2) 3) 4) 6.2 Check that each connector is firmly connected. Clean corroded or soiled connectors. Check coaxial cable for damage. If damaged, replace. Check that bolts fixing the antenna are firmly tightened.
PAGE 98
6. MAINTENANCE & TROUBLESHOOTING 6.3 Daily Test Authorities require that the DSC be checked daily for proper operation to ensure that it will function properly in the event of distress. Execute the daily test as below. 1. At the standby display, press the SHIFT key and TEST key in that order. The following display appears for test. And distress alarm (visual and audible) occurs. Test in progress (Pop-up display appears momentarily.
PAGE 99
8. MAINTENANCE & TROUBLESHOOTING 6.4 Error Message The table below shows all the error messages which may appear. Error message 6.5 Meaning PLL1 Unlock PLL circuit on the TX/RX pcb 05P0774 has unlocked. PLL2 Unlock PLL circuit on the DUP RX pcb 05P0777 has unlocked (only FM-8800D). ANT ERROR The antenna is abnormal. In this condition, if the transmission continues more than five seconds, the output power is reduced to approximately 10W.
PAGE 100
8.
PAGE 101
APPENDIX Menu Tree Bold: Default [MENU] POSITION OLDER EXT ALARM ALARM 4H/3H/2H/1H/0.
PAGE 102
APPENDIX 1 [CALL] COAST CALL SHIP CALL GROUP CALL PSTN CALL ALL SHIPS AREA CALL POSITION 1 AP-2 COAST ID ROUTINE BUSINESS SAFETY URGENCY DISTRESS TCmd1 SIMPLEX TP DUPLEX TP DATA FAX NO INFO TCmd2 CH SELECT CH / NO INFO SHIP ID ROUTINE BUSINESS SAFETY URGENCY DISTRESS TCmd1 SIMPLEX TP DUPLEX TP DATA FAX NO INFO TCmd2 CH SELECT CH / NO INFO GROUP ID ROUTINE BUSINESS SAFETY URGENCY DISTRESS TCmd1 SIMPLEX TP DUPLEX TP DATA FAX NO INFO TCmd2 SELECT CH / NO INFO CH COAST ID TCmd1 SIMPLEX TP DUPLEX TP
PAGE 103
APPENDIX Marine VHF Channel Lists 1) International Channels CH 01 02 03 04 05 06 07 08 09 10 11 12 13 14 TX MHz 156.050 156.100 156.150 156.200 156.250 156.300 156.350 156.400 156.450 156.500 156.550 156.600 156.650 156.700 RX MHz 160.650 160.700 160.750 160.800 160.850 156.300 160.950 156.400 156.450 156.500 156.550 156.600 156.650 156.700 15 156.750 156.750 16 17 18 19 20 21 22 23 24 25 26 27 28 156.800 156.850 156.900 156.950 157.000 157.050 157.100 157.150 157.200 157.250 157.300 157.350 157.
PAGE 104
APPENDIX 2) USA Channels TX MHz CH 01 156.050 02 03 04 05 156.250 06 156.300 07 156.350 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 156.400 156.450 156.500 156.550 156.600 156.650 156.700 156.800 156.850 156.900 156.950 157.000 157.050 157.100 157.150 157.200 157.250 157.300 157.350 157.400 RX MHz 156.050 156.250 156.300 156.350 Remark 156.400 156.450 156.500 156.550 156.600 156.650 156.700 156.750 156.800 156.850 Low PWR Low PWR 156.900 156.950 157.000 157.050 157.100 157.
PAGE 105
APPENDIX 3) Canadian Channels CH 01 02 03 04 05 TX MHz 156.050 156.100 156.150 156.200 156.250 RX MHz 160.650 160.700 160.750 156.200 156.250 06 07 08 09 10 11 12 13 14 156.300 156.350 156.400 156.450 156.500 156.550 156.600 156.650 156.700 156.300 156.350 156.400 156.450 156.500 156.550 156.600 156.650 156.700 15 16 156.750 156.800 156.750 156.800 17 156.850 156.850 18 19 156.900 156.950 156.900 156.950 20 21 22 23 24 25 26 27 28 157.000 157.050 157.100 157.150 157.200 157.250 157.300 157.
PAGE 106
APPENDIX 4) Inland waterways (INLND-WA) Channels CH 01 02 03 04 05 06 07 08 09 TX MHz 156.050 156.100 156.150 156.200 156.250 156.300 156.350 156.400 156.450 RX MHz 160.650 160.700 160.750 160.800 160.850 156.300 160.950 156.400 156.450 10 156.500 156.500 11 156.550 156.550 12 156.600 156.600 13 156.650 156.650 14 156.700 156.700 15 16 156.750 156.800 156.750 156.800 17 156.850 156.850 18 19 20 21 22 23 24 25 26 27 28 AP-6 156.900 156.950 157.000 157.050 157.100 157.150 157.
PAGE 107
APPENDIX 5) Private Channels Note: Bold for FM-8800D duplex TX frequencies TX RX FM-8800S FM-8800D Simplex Sim/Dup FM-8800S FM-8800D Simplex Duplex CH NO（current） Simplex Semi-dup 155.000 155.000 159.600 180 155.025 155.025 159.625 181 155.050 155.050 159.650 182 155.075 155.075 159.675 183 155.100 155.100 159.700 184 155.125 155.125 159.725 185 155.150 155.150 159.750 186 155.175 155.175 159.775 187 155.200 155.200 159.800 188 155.225 155.225 159.
PAGE 108
APPENDIX TX RX FM-8800S FM-8800D FM-8800S FM-8800D Simplex Sim/Dup Simplex Semi-dup Simplex Duplex 155.975 155.975 155.975 160.575 155.975 156.000 156.000 156.000 160.600 156.000 160.600 156.025 156.025 156.025 160.625 156.025 160.625 156.050 156.050 156.050 160.650 156.050 160.650 156.075 156.075 156.075 160.675 156.075 160.675 156.100 156.100 156.100 160.700 156.100 160.700 156.125 156.125 156.125 160.725 156.125 160.725 156.150 156.150 156.150 160.
PAGE 109
APPENDIX TX RX FM-8800S FM-8800D FM-8800S FM-8800D Simplex Sim/Dup Simplex Semi-dup Simplex Duplex 156.975 156.975 156.975 161.575 156.975 161.575 157.000 157.000 157.000 161.600 157.000 161.600 157.025 157.025 157.025 161.625 157.025 161.625 157.050 157.050 157.050 161.650 157.050 161.650 157.075 157.075 157.075 161.675 157.075 161.675 157.100 157.100 157.100 161.700 157.100 161.700 157.125 157.125 157.125 161.725 157.125 161.725 157.150 157.150 157.
PAGE 110
APPENDIX TX RX FM-8800S FM-8800D FM-8800S FM-8800D Simplex Sim/Dup Simplex Semi-dup Simplex 157.975 157.975 157.975 162.575 157.975 158.000 158.000 158.000 162.600 158.000 158.025 158.025 162.625 158.025 158.050 158.050 162.650 158.050 158.075 158.075 162.675 158.075 158.100 158.100 162.700 158.100 158.125 158.125 162.725 158.125 158.150 158.150 162.750 158.150 158.175 158.175 162.775 158.175 158.200 158.200 162.800 158.200 158.225 158.225 162.825 158.
PAGE 111
APPENDIX TX RX FM-8800S FM-8800D Simplex Sim/Dup FM-8800S FM-8800D Duplex CH NO（current） Simplex Semi-dup Simplex 158.975 158.975 163.575 158.975 159.000 159.000 163.600 159.000 200 159.025 159.025 159.025 201 159.050 159.050 159.050 202 159.075 159.075 159.075 203 159.100 159.100 159.100 204 159.125 159.125 159.125 205 159.150 159.150 159.150 206 159.175 159.175 159.175 207 159.200 159.200 159.200 208 159.225 159.225 159.225 209 159.250 159.250 159.
PAGE 112
APPENDIX TX RX FM-8800S FM-8800D Simplex Sim/Dup FM-8800S Simplex Semi-dup FM-8800D Simplex Duplex CH NO（current） Remark 159.975 159.975 159.975 239 160.000 160.000 160.000 240 160.025 160.025 160.025 241 160.050 160.050 160.050 242 160.075 160.075 160.075 243 160.100 160.100 160.100 244 160.125 160.125 160.125 245 160.150 160.150 160.150 246 160.175 160.175 160.175 247 160.200 160.200 160.200 248 160.225 160.225 160.225 249 160.250 160.250 160.
PAGE 113
APPENDIX TX RX FM-8800S FM-8800D Simplex Sim/Dup FM-8800S Simplex Semi-dup FM-8800D Simplex Duplex CH NO（current） 160.975 160.975 160.975 159 161.000 161.000 161.000 160 161.025 161.025 161.025 161 161.050 161.050 161.050 162 161.075 161.075 161.075 163 161.100 161.100 161.100 164 161.125 161.125 161.125 165 161.150 161.150 161.150 166 161.175 161.175 161.175 167 161.200 161.200 161.200 168 161.225 161.225 161.225 169 161.250 161.250 161.250 170 161.
PAGE 114
APPENDIX Digital Interface (IEC 61162-1 Edition 2) Input sentences GGA, GLL, RMC, ZDA, GNS Schematic diagram R70 10 05P0773 J2 TXD-H 7 TXD-C 8 RXD-H 9 RXD-C 10 Isolation Input impedance Max.
PAGE 115
APPENDIX GGA - Global positioning system (GPS) fix data
PAGE 116
APPENDIX GLL - Geographic position - latitude and longitude !"# $%& '"( )* $+ ,$ $% # - . / 0. %/ 1$ % 2 $34 %$ 5 26 !7*' 8$ $% %& 1$ % 2 $3. $%$ $ 9 . 9 ++ 3 % ' .
PAGE 117
APPENDIX RMC - Recommemded minimum specific GPS/TRANSIT data $--RMC,hhmmss.ss,A,llll.lll,a,yyyyy.yyy,a,x.x,x.x,xxxxxx,x.
PAGE 118
APPENDIX TLL – Target latitude and longitude $--TLL,xx,llll.lll,a,yyyyy.yyy,a,c--c,hhmmss.ss,a,a*hh | | | | | | | | | | | | | | | | | | | +--------- 8 | | | | | | | | +----------- 7 | | | | | | | +------------- 6 | | | | | | +-------------------- 5 | | | | | +-------------------------- 4 | | | +-----+------------------------------ 3 | +----+------------------------------------------ 2 +----------------------------------------------------- 1 1. Target number 00 - 99 2. Latitude, N/S 3.
PAGE 119
APPENDIX Thermal Printer UTP-80FK 1. Printer usage cautions • Do not disassemble or attempt to repair the printer. • Do not allow water to enter the printer. • Do not drop or jar the printer. • Fix a paper jam after turning off the power. • Turn off the power when there is some problem (for example, strange smell or smoke), and confirm that the trouble is not continuous. 2.
PAGE 120
APPENDIX Parts Paper feed slot Shaft VR for adjusting printing density Case Vent DIP switch Guard plate A Guard plate B Front panel Cutter Lock lever Feeder Frame of printer Frame of case Rear panel Screw hole for fixing case I/O connector 4. Operation Loading roll paper 1) Unlocking the Slide lock Slide the Lock lever at the right bottom of the panel to the FREE position to unlock the front panel1. 2) Pushing the panel Push the center of the front panel about 2 mm inward.
PAGE 121
APPENDIX 5) Attaching roll paper Insert roll paper into the shaft. NOTE) Insert the paper so it feeds from above as shown in the figure at right. 6) Inserting paper Turn on the POWER and confirm that the PE LED lights red. Insert paper through paper feed slot. The PE LED goes off then paper is fed. Feeding stops after the paper is fed a certain amount. 7) Pulling down the panel After setting paper, pull the bottom of the panel downward to fix the panel. Confirm that a click sounds.
PAGE 122
APPENDIX • Lock lever: the front panel. Cutter: Paper feed slot: • • Locks the front panel. The LOCK position prevents opening of Cuts paper. Pull up the paper to cut it. Feeds paper. Setting the DIP switch The DIP switch at the top of the frame functions to change printer specifications. Default specifications are shown in the table below.
PAGE 123
APPENDIX Printing test Turn on the power while pressing and holding down the FEED switch to start the test printing. All standard characters and six lines of filled squares are printed and then the equipment goes into ON-LINE. To stop printing during the test, hit the SEL key. NOTE1: Below are samples for 20 digits printing. NOTE2: The program number and date will be different on your printout. Remedy for paper jam 1) Turn off power When paper jam, turns off power immediately.
PAGE 124
APPENDIX 4) Removing jammed paper a) Remove paper carefully from the paper feed slot. b) If torn paper cannot be removed with fingers use a tweezers, being careful not to scratch parts. NOTE) Scratched printing head, platen or rubber roller can cause printing or paper feed malfunction. c) If torn paper cannot be removed, consult a FURUNO dealer for advice. Rubber roller (one each right and left) Platen Retainer plate (SUS) Head 5) Setting paper Set paper as mentioned earlier. 5.
PAGE 125
APPENDIX Thermal Printer UTP-58E For general operation notice, see Thermal printer UTP-80FK. UTP-58E for RC-8800S/D-B (Rack Console) and PP-8800A (Printer) Push the upper part of POWER switch and the READY lamp goes on. If the READY lamp does not light, set a roll paper as shown below. When the lamp is on, data received from the radiotelephone is printed. After completion of printing, feed paper out by pressing the FEED button.
PAGE 126
APPENDIX This page is intentionally left blank.
PAGE 127
INDEX A L Able acknowledge call.................................3-5 ACK BQ .......................................................3-7 Alarm setup..................................................4-1 All ships call...............................................3-16 Audio alarms................................................1-6 Auto ACK setup ...........................................4-3 Automatic acknowledge .....................1-11, 3-7 LCD..............................................................
PAGE 128
INDEX U V Unable acknowledge call.............................3-5 Volume.........................................................1-8 Volume setup.............................................
PAGE 129
FURUNO ELECTRIC CO., LTD. 9-52 Ashihara-Cho, Nishinomiya City, 662-8580, Hyogo, Japan Tel: +81 798-65-2111 Fax: +81 798-65-4200 Pub NO. DOC-913 Declaration of conformity We FURUNO ELECTRIC CO., LTD.