DF3600U Universal Flash SUNPAK DF3600U
Thank you for purchasing this Sunpak flash. Before using the DF3600U, please take a moment to read this manual and your camera’s instruction manual to familiarize yourself with the flash operations. Safety instruction 1, Never trigger the flash around flammable gas or liquid gas (such as gasoline and solvents)! There is risk of explosion! 2, Neither shoot with the flash at drivers who are driving cars, buses or trains, nor the rider of motor and bicycle.
Description of Parts Built-in bounce card Flash head tilt angle scale Built-in wide-angle diffuser Flash head Serial number Liquid crystal display Synchronous sockets Press two button at the same time restore factory settings High-speed synchronous / Rear-curtain sync / Ordinary flash switch button Parameter Settings button / MASTER select button Backlight / LED Mode switch button MODE select buttons / SLAVE select button Focal length/ Wireless parameter settings button / Custom function settings but
Auto-focus auxiliary AF assist lamp When shooting under a dark conditions, the Automatic AF Assist which is built into the flash light may temporarily project red light to assist focusing. In some cases it may interfere with your subject. If this happens, you can switch to Manual focus (M) or to the Custom function (Fn - 08) close focus light.
Applicable batteries and power supply. Install the battery The following batteries are applicable to the flash. Lithium battery installation 1, AA battery A:4 (AA) Alkaline manganese battery (1.5V). The battery can meet demand of medium power without maintenance, but it can not be recharge. B:4 (AA) Nickel-cadmium battery (1.2V). The battery recycles quickly and can be recharged, so it is economic and practical. 1, Open the battery cover.
Install flash to camera 1.Prepare to install the fkash According to the direction indicated by an arrow will spin lock dial to the left side. 2.Install the flash According to the direction indicated by an arrow will flash installed foot completely inserted into the camera's hot shoe. 3.Lock the flash According to the direction indicated by an arrow will spin lock dial to the right to lock the flash. Turn on the power Press the Power button (ON/ OFF ) for two seconds to turn on/off the flash.
FEB setting value Common flash mode Divided into Automatic flash mode, TTL mode, M manual flash and Stroboscopic flash mode Multi. Automatic TTL flash mode Set the camera's shooting mode to < P > (Program Auto Exposure) or Green frame < □ > (Auto), fully Automatic flash will make flash photography and modes of the < P > and < □ > as simple as Ordinary TTL Mode flash. Select the flash mode 1.Press MODE flash mode select button in common flash mode. 2.Press 【MODE】 mode button until the LCD display .
3, Complete setup After set up press again the【 Parameter Settings button 】to exit the set status. If FEB value is not 0 displays, as shown by the custom function can be set FEB exposure sequence.
1/X sec.is the camera's maximum flash sync speed. Note: The Canon camera mode: P, TV, AV, M, A - DEP, green frame Nikon mode: P, S, A, M Manual flash mode M When you need to manually exposure, You can set the flash brightness according to your own needs. From 1/128 power to 1/1 full power to adjust the incremental setting the flash output. more than 10 consecutive frequency glint light shoot. Between exposure operation, please let the flash have enough time to call back.
Note: ·Stroboscopic mode, Use the following formula to determine the shutter speed, and then use the step is smaller than the shutter speed of one or more long shutter speed. ·The shutter speed = Times of flash÷Flash frequency (Hz) ·The shutter speed, can be used with B door “ ”High speed “ ” Rear-Curtain sync Settings High-speed synchronous: Synchronous operation of flash and camera with high shutter speed, The maximum shutter speed of up to 1/8000s.
【ZOOM】settings Press ‘ZOOM button’ to display flicking. The flash will default to A (Automatically zooms with the lens). To manually change to a different focal length, press the Right Button to go to Manual, them continue pressing until you reach the desired setting. Use the Left Button to decrease the focal length and keep pressing until it goes back to A. Press "ZOOM button" to exit setup.
trigger to MASTER light.Before shooting ,we need set up the same channel about flash light and MASTER light. Short press (Zoom button): until channel or group twinkle as for SLAVE unit ,setting Communication channel of SLAVE unit (1.2.3.4) and SLAVE unit group (A.B.C) S1 S2 Note: 1, Short press 【Flash model select button】 only change SLAVE flash model in Wireless SLAVE flash model.
Wireless optical flash model(S1,S2) Rotating the flash lamp, the signal transmitter should toward to the MASTER speedlight in S1, S2 mode. Setting optical flash model: 1, Press 【Flash model select button】 until LCD display S1/S2 model in Wireless flash model.These two models are suitable for the side effect of the machine, to create a variety of lighting effects. They are suitable for manual flash and TTL flash environment. 2, In these two modes, the output brightness is adjusted to the same as the M mode.
2, Wireless optical flash Using built-in flash light or outlay flash light as MASTER MASTER flash light.Please put different angel. wireless channel will be reflect back by wall in indoor.So please choose more space to put flash light. After improved Wireless trigger inductor ,the trigger induction faster , S1 and S2 model availbe for outdoor.The distance 15 meters by wireless trigger inductor.Put SLAVE light ,please test S1 or S2 whether is work before shooting.
According to your request to set up customer menu. Automatic save function Customer menu setting:Long press 【Customer menu button】” as left picture ; Press
Bounce Flash Use the built-in wide-angle diffuser Reflection flash is by putting a flash head toward the wall or ceiling, flash be metope reflect in front of the illuminated by the object. This can reduce the shadow on the reverse of the subject object, in order to obtain more natural photographic effect. When the camera to the subject's distance is less than 2m, you can use the wide angle diffuser plate more naturally close-up.
Specification Circuit design: Insulated gate bipolar transistor (IGBT) Guide Number: 118 (ISO100,180 mm) Flash coverage: Manual/Automatic zoom18 ~ 180 mm Flash head rotation to achieve reflection flash TTL flash mode: Automatic mode, Manual mode M, Stroboscopic mode Multi, LED lighting, canon master,Nikon Master models, Slave light SLAVE c, SLAVE n, Light flash mode S1, S2, Surrounded by flash exposure (FEB) Wireless trigger: Light pulse, Induction flash light Wireless flash distance: Indoor 20 ~ 30 meters,
