D.C.C. 2017.09.04 SUNON SPECIFICATION FOR APPROVAL DRAWN CUSTOMER : MOTOR TYPE : DESCRIPTION : MagLev Motor Fan DIMENSIONS : 80X80X25 mm MODEL : PF80251V1-10000-S99 SUNON SPEC. NO. : D08058480G-01 CUSTOMER APPROVAL NO. APPROVED BY CUSTOMER (AUTHORIZED) : yoKung 07/26 CHECKED : Kelly Chin-Jung APPROVED SPEC.NO D08058480G-01 ISSUE DATE 07.26.2017 Gavinlee EDITION 0 REVISION DATE E.SPEC E11400311 建準電機工業股份有限公司 SUNONWEALTH ELECTRIC MACHINE INDUSTRY CO., LTD. NO. 30, LN.
D.C.C. 2017.09.04 I.
D.C.C. 2017.09.04 II. SPECIFICATION 1. MECHANICAL CHARACTERISTIC MOTOR DESIGN Single phase, 4-poles Brushless DC motor BEARING SYSTEM Vapo bearing system DIMENSIONS See Page 6 MATERIALS OF FRAME Thermoplastic PBT of UL 94V-0 MATERIALS OF FAN BLADE Thermoplastic PBT of UL 94V-0 DIRECTION OF ROTATION Counter-clockwise viewed from front of fan blade MOUNTING HOLES Diameter 4.3 mm in 8 holes WEIGHT 91 g 2. ELECTRIC CHARACTERISTIC RATED VOLTAGE 12 VDC RATED CURRENT 310 mA / MAX.
D.C.C. 2017.09.04 3. PERFORMANCE CHARACTERISTIC RATED SPEED 4800 RPM ± 10% at rated voltage AIR FLOW 60 CFM STATIC PRESSURE 0.41 Inch-H 2 O ACOUSTIC NOISE 44.7 dB(A) AIR FLOW V.S. PRESSURE See Page 5 INSULATION CLASS UL Class A INSULATION RESISTANCE 10M ohm at 500 VDC between internal stator and lead wire (+) PLASTIC HOUSING DIELECTRIC STRENGTH Applied AC 500 V for one minute or AC 600 V for 2 Seconds between housing and lead wire (+) LIFE EXPECTANCY 60,000 hrs at 40 deg.
D.C.C. 2017.09.04 MODEL : PF80251V1-10000-S99 PERFORMANCE 0 0.28 0.56 0.84 1.12 CURVES 1.4 0.4 10.16 0.3 7.62 0.2 5.08 0.1 2.54 mm-H2O Static Pressure (Inch-H2O) 0.5 1.68 m3/min 12.
D.C.C. 2017.09.04 DIMENSIONS Screw Type (Pan head) Torque Machine screw Self-tapping screw Screw Spec Size Standard 3～4 Kgf-cm M4.0 JIS B1111-1974 5～6 Kgf-cm ∮5.0 JIS B1122 Type 2 Note: SUNON recommends the screw and torque as above. Please contact SUNON, if any new requirement is requested.
D.C.C. 2017.09.
D.C.C. 2017.09.
D.C.C. 2017.09.04 PWM INPUT SIGNAL System System Fan Fan Vcc Vcc = = rated rated volt. volt. +6V +6V 10K 10K PWM PWM Input Input Isource Isource 4.7K 4.7K 10K 10K Ground Ground ★PWM INPUT WAVEFORM V VH H VLL tt1 1 t2 T T 1. Period : T 2. Duty Cycle（D.C.） : = 1 f = t1 + t2(sec) . PWM t1 t1 ∗100 = ∗100(% ) . T t1 + t2 3.PWM Duty Cycle VS Speed (at Ta = 25℃,Vcc =Rated Volt.,fpwm= 25 KHz) PWM Duty Cycle (%) FAN Speed（ R.P.M.）(REF.
III. OTHER SPECIFIED TESTING The following is a general description of certain tests that are performed on representative SUNON fans. Nothing in this document is intended to suggest that these tests are performed on every model of SUNON fan. Moreover, the descriptions that follow each test are meant only to provide a general explanation of each test. If you would like a more detailed explanation as to any test identified in this Section, SUNON can provide such an explanation upon request. 1.
IV. CHARACTERISTIC DEFINITION The following is a general description of certain tests that are performed on representative SUNON fans in order to determine the specifications of the fan. Nothing in this document is intended to suggest that these tests are performed on every model of SUNON fan. Moreover, the descriptions that follow each test are meant only to provide a general explanation of each test.
4. RATED SPEED Measured after continuous 10 minute operation at rated voltage in clean air ( STATIC PRESSURE=0), and at ambient temperature of 25 degrees C under shaft horizontal condition. 5. STARTING VOLTAGE Measured the voltage which enables to start the fan in the clean air (static pressure = 0 ) by switching on at the voltage under shaft horizontal condition. It is not at continuously increasing voltage adjustment. 6. LOCKED ROTOR CURRENT Measured immediately after the fan blade is locked. 7.
D.C.C. 2017.09.04 V. NOTE Ⅰ.SAFETY 1. DO NOT use or operate this fan in excess of the limitations set forth in this specification. SUNON is not responsible for the non-performance of this fan and/or any damages resulting from its use, if it is not used or operated in accordance with the specifications. 2. SUNON recommends adding a protection circuit to the product or application in which this fan is installed, such as a thermo-fuse, or current-fuse or thermo-protector.
II. SPECIFICATION MODIFICATION 1. SUNON offers engineering assistance on fan installation and cooling system design. 2. All changes, modifications and/or revisions to the specifications, if any, are incorporated in the attached specifications. 3. No changes, modifications and/or revisions to these specifications are effective absent agreement, by both SUNON and the customer, in writing. 4.
7. Unless otherwise noted, all testing of this fan is conducted at 25°C ambient temperature and sixty-five percent (65%) relative humidity. 8. DO NOT store this fan in an environment with high humidity. This fan must be stored in accordance with the attached specifications regarding storage temperature. If this fan is stored for more than 6 months, SUNON recommends functional testing before using. 9. SUNON reserves the right to use components from multiple sources at its discretion.
D.C.C. 2017.09.04 Declaration of RoHS Control declaration of environment-related substances/materials 1. In accordance with the Restriction of Hazardous Substances (RoHS) Directive 2011/65/EU, SUNON product have complied with law and discipline not to employ the forbidden substances, and restrict the allowable concentration of some limited substances deliberately in our components.
