Quick Start Guide

ManualsBrandsSUNMI ManualsPOS EquipmentWireless data POS System(T5930)

Quick start

Printer

For printing sales slips in power on mode.

Power button

Short press: wake up the screen, lock the screen.

Long press: long press for 2-3 seconds in power o mode to

switch on the device.

Long press for 2-3 seconds in normal operation mode to select

power o or reboot.

Long press for 11 seconds when system is frozenfor automatic

reboot.

Volume key

Volume adjustment.

Type-C USB

For device recharging and developer debugging.

Camera

For payment scanning and 1D/2D code quick scanning.

Extended interface

Used to connect the base (this accessory needs to be purchased

separately).

SIM Card Slot

Note: To prevent system errors, please make sure the device is

turned o when you insert or remove the SIM card.

This device supports 58mm thermal paper with the specications of

57±0.5mm*Ø50mm.

① Please open the paper container with the uncovering handl ，

Please do not force open the paper container to avoid print head

gear wear;

② Feed the paper correctly into the paper container in the direction

as shown, and pull some paper outside the cutter;

③ Close the cover of the paper container to nish printing paper

feeding.

Note: If the printed paper is blank, please check whether the paper

roll has been installed in the correct direction.

Printing instructions

Notices

Safety Warning

Connect the AC plug to the AC socket corresponding to the marked

input of the power adapter;

To avoid injury, unauthorized persons shall not open the power

adapter;

This is a Class A product. This product may cause radio interference

in living environments.

In that case, the user may be required to take adequate measures

against interference.

Battery replacement:

1.Explosion danger may arise if replacing with the wrong battery!

2.The replaced battery shall be disposed of by maintenance

personnel, and please do not throw it into re!

Signicant Safety Instructions

Do not install or use the device during lightning storms to avoid the

potential risks of lightning shock;

Please turn o the power immediately if you notice abnormal odor,

heat or smoke;

The paper cutter is sharp, please do not touch!

Suggestions

· Do not use the terminal near water or moisture to prevent liquid

from falling into the terminal;

Do not use the terminal in extremely cold or hot environments, such

as near ames or lit cigarettes;

Do not drop, throw or bend the device;

Use the terminal in a clean and dust-free environment if possible to

prevent small items from falling into the terminal;

Please do not use the terminal near medical equipment without

permission.

Statements

The Company does not assume responsibilities for the following

actions:

Damages caused by use and maintenance without complying with

the conditions specied in this guide;

The Company will not assume any responsibilities for the damages or

problemscaused by optional items or consumables (rather than the

initial products or approvedproducts of the Company). The customer

is not entitled to change or modify the product without our consent.

The product’s operating system supports ocial systemupdates, but

if you change the operating system into a third party ROM system or

alter the system les by system cracking, it may cause system

instability and security risks and threats.

Disclaimer

As a result of product upgrading, some details in this document may

not match the product, and the actual product shall govern. The

Company reserves the right of interpretation of this document. The

Company also reserves the right toalter this specication without

prior notice.

Table for Names and Content Identication of Toxic and

Hazardous Substances in this Product

indicates that the content of the toxic and hazardous substance in all homogeneous

materials of the component is below the limit specied in SJ/T 11363-2006.

indicates that the content of the toxic and hazardous substance in at least one

homogeneous material of the component exceeds the limit stipulated in SJ/T

11363-2006. However, as for the reason, because there is no mature and replaceable

technology in the industry at present.

：

The products that have reached or exceeded environmental protection service life should

be recycled and reused according to the Regulations on Control and Management of

Electronic Information Products, and should not be discarded randomly.

Part Name

Toxic or Hazardous Substances and Elements

Circuit Board Component

Structural Component

DBP

Packaging Component

Cr(VI)

PBB PBDE DEHP BBP DIBPHg

CE certication information (SAR)

This device was tested for typical body-worn operations with the back of the handset kept

5mm away. To maintain compliance with RF exposure requirements, use accessories that

maintain a 5mm separation distance between the user's body and the back of the

handset. The use of belt clips, holsters and similar accessories should not contain metallic

components in its assembly. The use of accessories that do not satisfy these requirements

may not comply with RF exposure requirements, and should be avoided.

If you are using pacemaker, hearing aid, cochlear implant or other device, please use the

phone according to the doctor’s advice.

PRODUCT SAFETY WARNINGS

Use responsibly. Read all instructions and safety information before use to avoid

injury.The limit operating ambient temperature of the equipment declared by the

manufacturer is -15~55°C

Battery safety

Charge battery only at ambient temperatures ranging from 40°C.

(1) CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the

same or equivalent type of battery recommended by the manufacturer. Dispose of used

batteries according to battery manufacturer’s instructions.

(2) CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.

DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.

(3) CAUTION:Battery charging temperature upper limit is 40°C.

Adapter safety

When charging, please place the device in an environment that has a normal room

temperature and good ventilation. It is recommended to charge the device in an

environment with a temperature that ranges from 0°C~40°C.

For altitude 2km below use only

Wi-Fi Safety

Turn Wi-Fi o in areas where Wi-Fi use is prohibited or when it may cause interference or

danger, such as in airplanes while ying.

Declaration of Conformity

Hereby, Shanghai Sunmi Technology Co., Ltd. declares that the Wireless data POS

System(Model No.:T5930) is in compliance with the essential requirements and other

relevant provisions of RED 2014/53/EU.

CAUTION: The device is restricted to indoor use when operated in the European

Community using frequency in 5150MHz~5250MHz to reduce the potential for

interference.

5.8G SRD receiver category：1

Technical features and characteristic

Operation Frequency Transmitted

880.0–915.0MHz(TX), 925.0–960.0MHz(RX)

1710.0–1785.0MHz (TX), 1805.0–1880.0 MHz (RX)

1920-1980MHz (TX), 2110-2170MHz (RX)

880-915MHz (TX), 925-960MHz (RX)

1920-1980MHz (TX), 2110-2170MHz (RX)

1710-1785 MHz (TX), 1805-1880MHz (RX)

2500-2570MHz(TX), 2620-2690MHz(RX)

880-915MHz(TX) , 925-960MHz(RX)

832-862MHz(TX),791-821MHz(RX)

2570-2620MHz (TX/RX)

2300-2400MHz (TX/RX)

2402MHz-2480MHz

2412MHz-2472MHz

5.15-5.35GHz

5.725-5.850GHz

32.5dBm

29.5dBm

21dBm

22.5dBm

23dBm

22.5dBm

21.5dBm

22dBm

7dBm

15dBm

16.5dBm

13.5dBm

GSM 900

GSM 1800

WCDMA Band I

WCDMA Band VIII

LTE BAND 1

LTE BAND 3

LTE BAND 7

LTE BAND 8

LTE BAND 20

LTE BAND 38

LTE BAND 40

BT/BLE

2.4G Wi-Fi

5G Wi-Fi

Manufacture

Shanghai Sunmi Technology Co., Ltd.

Room 505, KIC Plaza, No.388 Song Hu Road, Yang Pu District, Shanghai, China

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including

interference that may cause undesired operation.

FCC ID: 2AH25V2

NOTE: Changes or modications not expressly approved by the party responsible for

compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation.

If this equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment o and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

---Reorient or relocate the receiving antenna.

---Increase the separation between the equipment and receiver.

---Connect the equipment into an outlet on a circuit dierent from that to which the

receiver is connected.

---Consult the dealer or an experienced radio/TV technician for help.

Body-worn Operation

This device was tested for typical body-worn operations. To comply With RF exposure

requirements, a minimum separation distance of 1.0cm must be maintained between the

user’s body and the handset, including the antenna.

Third-party belt-clips, holsters, and similar including the antenna. Third-party belt-clips,

holsters, and similar accessories used by this device should not contain any metallic

components. Body-worn accessories that do not meet these requirements may not

comply with RF exposure requirements and should be

avoided.

Specic Absorption Rate (SAR) information:

This wireless data POS System meets the government's requirements for exposure to

radio waves. The guidelines are based on standards that were developed by independent

scientic organizations through periodic and thorough evaluation of scientic studies.

The standards include a substantial safety margin designed to assure the safety of all

persons regardless of age or health.

FCC RF Exposure Information and Statement. The SAR limit of USA (FCC) is 1.6W/kg

averaged over one gram of tissue.

Device types: T5930 has also been tested against this SAR limit. The highest SAR value

reported under this standard during product certication when properly worn on the

body is 1.042W/kg（10gSAR， test distance：0mm，limit 4W/kg）and

0.983W/kg (1gSAR， test distance：5mm，limit 1.6W/kg). This device was tested for

body-worn operations with the back of the handset kept 10mm and 5mm from the body.

To maintain compliance with FCC RF exposure requirements, use accessories that

maintain a 10mm and 5mm separation distance between the user's body and the back of

the handset. The use of belt clips, holsters and similar accessories should not contain

metallic components in its assembly. The use of accessories that do not satisfy these

requirements may not comply with FCC RF exposure requirements, and should be

avoided.

Technical features and characteristic

Operation Frequency Transmitted

GSM 850

GSM 1900

WCDMA BAND II

WCDMA BAND IV

WCDMA BAND V

LTE BAND 2

LTE BAND 4

LTE BAND 7

LTE BAND 17

2.4G Wi-Fi

Bluetooth

BLE

5G Wi-Fi

824-849 MHz(Tx),869-894 MHz(Rx)

1850-1910 MHz(Tx),1930-1990 MHz(Rx)

1710 -1755 MHz(Tx),2110 - 2155MHz(Rx)

824-849 MHz(Tx),869-894 MHz(Rx)

1850-1910 MHz(Tx),1930-1990 MHz(Rx)

1710-1755 MHz(Tx),2110-2155 MHz(Rx)

2500-2570 MHz(Tx),2620-2690 MHz(Rx)

704-716 MHz(Tx),734-746 MHz(Rx)

2412-2462 MHz

2402-2480 MHz

5150-5250 MHz

5725-5850 MHz

32 dBm

30 dBm

23 dBm

23.5 dBm

22.5 dBm

23 dBm

15 dBm

6 dBm

17 dBm

16.5 dBm

Descripción del Producto

Impresora

Se utiliza para imprimir documentos cuando esté encendido.

Botón de encendido

Pulse brevemente: Para encender y bloquear la pantalla. Pulse

prolongada- mente:

Cuando esté apagado, pulse prolongadamente durante 2-3 segundos

para encender;

Durante su uso, mantenga pulsado durante 2-3 segundos, para apagar

o reiniciar el aparato;

En estado muerto, pulse durante 11 segundos y se reiniciará

automáticamente.

Botón de volumen

Ajuste el nivel del volumen

Puerto Tipo-C

Se puede utilizar para cargar el dispositivo y para depurar

desarrolladores.

Cámara

Puede tomar fotos y escaneo rápido de los códigos de barras 1D/2D.

Extensible Interface

Para conectar la base (este accesorio necesita ser adquirido por

separado).

Ranura para tarjeta SIM

Nota: Cuando inserte o extraiga la tarjeta Nano SIM, asegúrese de dejar

el aparato apagado, ya que al enchufar y desenchufar en el estado de

encendido podría causar un fallo en el aparato.

Este aparato se puede usar papel térmico de 58mm, especica- ciones:

57±0.5mm×Ø50mm

Abra el compartimiento del papel de la impresora (ilustrado en la gura1)

no lo abra con fuerza para evitar el desgaste de la rueda dentada de la

impresora; Coloque el papel en el compartimiento del papel

correctamente siguiendo la dirección indicada en la gura y extraiga una

parte del papel fuera del cuchillo (Ilustrado en la gura2);

Cierre la tapa del compartimiento de papel para terminar de instalar

(ilustrado en la gura3).

Nota: Si el contenido impreso está en blanco, compruebe que la

orientación del rollo de papel está o no invertido.

Instrucciones para imprimir