Quick Start Guide

ManualsBrandsSUNMI ManualsPOS EquipmentWireless data POS System

Quick Start Printing Instructions

Notices

NFC Reader

For reading NFC cards, like loyalty cards.

Printer

For printing receipts when the device is on.

Scan Button/LED (optional)

Short press to enable barcode scanning function.

Type-C

For device charging and developer debugging.

Micro SD Card Slot/Nano SIM Card Slot

For installing the Micro SD card and Nano SIM card.

Front Camera (optional)

For video conference, or photo/video taking.

Power Button

Short press: wake up the screen, lock the screen.

Long press: long press for 2-3 seconds to turn on the device

when it is oﬀ. Long press for 2-3 seconds to select to power

oﬀ or reboot the device when it is on. Long press for 11

seconds to reboot a device when the system is frozen.

Volume Button

For volume adjustment.

Scanner (optional)

For barcode data collection.

Rear Camera

For photo taking and quick 1D/2D barcode reading.

Pogo pin

For connecting a barcode scanning accessory, or a cradle for

communication and charging.

PSAM Card Slots (optional)

For installing the PSAM cards.

PSAM1

PSAM2

PSAM3

PSAM4

This device can load a 80mm thermal receipt or label paper roll,

and black label is also optional.

The paper roll spec is 79±0.5mm×Ø50mm.

· Please press to open the printer (see ①). Please do

not force open the printer to avoid printhead gear wear;

· Load the paper into the printer and pull some paper outside

the cutter following the direction shown in ②;

· Close the cover to complete paper loading (see ③).

Notice: If the printer prints blank paper, please check whether

the paper roll has been loaded in the correct direction.

Tips: To clean a label printhead, it is recommended to use a

cotton swab dipped in alcohol or a alcohol prep pad (75%

isopropyl alcohol) to wipe the printhead.

Manufacture

Shanghai Sunmi Technology Co., Ltd.

Room 505, KIC Plaza, No.388 Song Hu Road, Yang Pu District,

Shanghai, China

Safety Warning

Connect the AC plug to the AC socket corresponding to the

marked input of the power adapter;

To avoid injury, unauthorized persons shall not open the

power adapter;

This is a Class A product. This product may cause radio

interference in living environments.

In that case, the user may be required to take adequate

measures against interference.

Battery replacement:

1.Explosion danger may arise if replacing with the wrong

battery!

2.The replaced battery shall be disposed of by maintenance

personnel, and please do not throw it into ﬁre!

Signiﬁcant Safety Instructions

Do not install or use the device during lightning storms to

avoid the potential risks of lightning shock;

Please turn oﬀ the power immediately if you notice abnormal

odor, heat or smoke;

The paper cutter is sharp, please do not touch!

Suggestions

· Do not use the terminal near water or moisture to prevent

liquid from falling into the terminal;

Do not use the terminal in extremely cold or hot environments,

such as near ﬂames or lit cigarettes;

Do not drop, throw or bend the device;

Use the terminal in a clean and dust-free environment if

possible to prevent small items from falling into the terminal;

Please do not use the terminal near medical equipment

without permission.

Statements

The Company does not assume responsibilities for the

following actions:

Damages caused by use and maintenance without complying

with the conditions speciﬁed in this guide;

The Company will not assume any responsibilities for the

damages or problemscaused by optional items or consum-

ables (rather than the initial products or approvedproducts of

the Company). The customer is not entitled to change or

modify the product without our consent.

The product’s operating system supports oﬃcial systemup-

dates, but if you change the operating system into a third party

ROM system or alter the system ﬁles by system cracking, it may

cause system instability and security risks and threats.

Disclaimer

As a result of product upgrading, some details in this

document may not match the product, and the actual product

shall govern. The Company reserves the right of interpretation

of this document. The Company also reserves the right toalter

this speciﬁcation without prior notice.

Table for Names and Content Identiﬁcation of Toxic and Hazardous

Substances in this Product

indicates that the content of the toxic and hazardous substance in all homogeneous materials of

the component is below the limit speciﬁed in SJ/T 11363-2006.

indicates that the content of the toxic and hazardous substance in at least one homogeneous

material of the component exceeds the limit stipulated in SJ/T 11363-2006. However, as for the

reason, because there is no mature and replaceable technology in the industry at present.

：

The products that have reached or exceeded environmental protection service life should be recycled

and reused according to the Regulations on Control and Management of Electronic Information

Products, and should not be discarded randomly.

Part Name

Toxic or Hazardous Substances and Elements

Pb Cd

Cr(VI)

PBB

Circuit Board Component

Structural Component

DBP

Packaging Component

Part Name

Toxic or Hazardous Substances and Elements

Hg PBDE

Circuit Board Component

Structural Component

DEHP BBP DIBP

Packaging Component

FCC Warning:

Please take attention that changes or modification not

expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received,

including interference that may cause undesired operation.

FCC SAR statement

This equipment complies with FCC radiation exposure

limits set forth for an uncontrolled environment. End user

must follow the specific operating instructions for satisfying

RF exposure compliance. This transmitter must not be co-

located or operating in conjunction with any other antenna

or transmitter.

The portable device is designed to meet the requirements

for exposure to radio waves established by the Federal

Communications Commission (USA). These requirements

set a SAR limit of 1.6 W/kg averaged over one gram of

tissue. The highest SAR value reported under this

standard during product certification for use when properly

worn on the body.