Installation Guide

ManualsBrandsSunlite ManualsCommercial Lighting48 in. Selectable Wattage Integrated LED White Strip Light Fixture Selectable CCT Dimmable

8~10m m

U L1 4~ 18A W G

8~10m m

U L1 4~ 18A W G

8~10m m

U L1 4~ 18A W G

8~ 1 0m m

U L14~ 1 8A W G

8~ 1 0m m

U L14~ 1 8A W G

8~ 1 0m m

U L14~ 1 8A W G

J-BOX(not provided)

1. Insert J-Box cover in to slots on the

bottom of the fixture like shown below

4. Insert anchors into drilled holes from

step3 and install fixture using provided

screws.

4FT 8FT

972±4mm 2172±4mm

2FT 3FT

538±4mm 838±4mm

Please read and understand this entire manual before attemptiong to assemble, operate or install the produc.

WARNINGS & CAUTIONS: Risk of fire or electric shock. Turn power off before inspection, installation code by a persion familiar with

the construction and operation of the product and the hazards involved. if you do not have sufficient electrical wiring experience,

please consult a qualified electrician. To prevent wiring damage of abrasion, do not expose wiring to edges of sheet metal or other

sharp objects. Do not install this fixture where there is risk of rain or moisture exposure. Install this kit only in the luminaires that have

construction features and dimnstions shown in the instructions. Ambient operation temperature -20℃~50 ℃(-4℉ ~122F). Min 90℃

supply conductors, Suitable for damp locations.

Remark: Ambient operation temperature -0℃~50 ℃(32℉ ~122F) for Emergency Battery.

Installation

2. Open the lens section. the lens will

hang off of the fixture hinge.

3. Drill mounting holes in ceiling using

reference guide

8~1 0m m

U L14~ 18A W G

8~1 0m m

U L14~ 18A W G

8~1 0m m

U L14~ 18A W G

8~ 10m m

U L14~ 18A W G

8~ 10m m

U L14~ 18A W G

8~ 10m m

U L14~ 18A W G

5. Connect supply wires to fixture wires. Black to

bllac, white to white, and green to green. for 0-

10v diming, connect the violet wire to the

positive dimming wire and the grey wire to the

negative dimming wire

CCT/W selectable switch

6. Select color temperature and wattage on

switches on the side of the fixture(shown below)

Suspended mount kit (sold seperately) 85636-SU

What the holes used for?

for Suspension installation(V-Hook).

for Surface installation(ceiling) and cornner bracket installation.

for Surface installation(ceiling with J-box).

Ceiling Mount

1. Attach V-Hooks to existing keyholes on the fixture. 2. Hang the v-hook on the chain.

3. Wiring method is the same as ceiling mount. All of the wiring

must to through a conduit.

Conduit (not provided)

Summary of content (4 pages)

PAGE 1
Please read and understand this entire manual before attemptiong to assemble, operate or install the produc. WARNINGS & CAUTIONS: Risk of fire or electric shock. Turn power off before inspection, installation code by a persion familiar with the construction and operation of the product and the hazards involved. if you do not have sufficient electrical wiring experience, please consult a qualified electrician.
PAGE 2
Linking Bracket for suspended mount(Sold seperately) 1. Insert the linking brakect on fixture then secure with screw as we provided Linking brakect Corner Bracket for corner mount(Sold seperately) 1. Drill mounting holes on the wall using the reference guide below. Corner brakect L 2FT 598±4mm 2. Insert anchors into the mounting holes then attach the corner bracket on the wall by screwing. screws into anchors. 3FT 898±4mm 4FT 8FT 1032±4mm 2232±4mm 3.
PAGE 3
With Emergency battery-4W （Sold seperately） Female connector to connect the male connector from the LED board Male connector to connect the female connector from the Driver output M4 screw nut Fast connector with black wire White wire to wiring to the connector from the fixture LED Driver 4W EM installed in the fixture by screw and nut 15mm knockout hole for install the test switch M4 screw for install the EM Test switch With Emergency battery-6W OR 8W （Sold seperately） Female connector to connect the
PAGE 4
1. Wiring(When fixture was installed EM). Input L black wire to wiring the EM connector. input L black wire to wiring the fixture connector. input N white wire to wiring the fixture connector. input Grond wire to wiring the fixture. 6 or 8W EM Wiring Diagram 8~10m m U L14~ 18A W G Fast connector from fixture Fast connector from EM charge Motion Sensor (Sold seperately） 1. install the 12V sensor on the fixture. and wiring to the driver by fast connector.