Assembly Instructions Item #: L-GZ605PST-A4 IMPORTANT Thank you very much for choosing Sunjoy Group. Please take time to read these instructions thoroughly and follow each step carefully for safe and easy operation. Keep this manual for future reference. We would like to hear from you with any comments or suggestions. You can call us toll-free at 1-866-578-6569 anytime 24 hours / 7 days a week. You can also send the email to customer.care@sunjoygroup.com or visit www.sunjoyonline.com to get tech.
Cautions: 1. Keep all children and pets away from assembly area. Children and pets should be supervised when they are in the area of pavilion construction. 2. The area for assembly should not be less than 6 feet from any obstruction such as fence, garage, house, over hanging branches, laundry line or electrical wires. 3. This unit is heavy. Do not assemble this item alone. Six people are recommended for safe assembly. 4. Some parts may contain sharp edges.
Parts List Front post 1 A1 1 Front post 2 A2 1 Back post 1 A3 1 Back post 2 A4 1 Side beam 1 B1 1 Side beam 2 B2 1 Decorative slot 1 C1 1 Decorative slot 2 C2 1 Junction bar D 1 Back beam 1 E1 1 Back beam 2 E2 1 Beam junction F 2 Middle beam 1 G1 1 Middle beam 2 G2 1 Small beam 1 H1 2 Small beam 2 H2 2 I 2 Back card slot 1 J1 1 Back card slot 2 J2 1 Front card slot 1 K1 2 Small beam junction
Front card slot 2 K2 1 Edge beam 1 L1 1 Edge beam 2 L2 1 Middle beam L3 4 PC panel 1 M1 10 PC panel 2 M2 1 PC panel 3 M3 1 PC panel 4 M4 1 PC panel 5 M5 1 PC penal card slot N 5 Side card slot 1 N1 1 Side card slot 2 N2 1 Post base 1 O1 2 Post base 2 O2 2 Post base cover 1 P1 2 Post base cover 2 P2 2 Curtain-mounting tab Q 4 Middle beam bracket R 2 Connecting piece 1 S1 12 Connecting piece 2 S2 4
Connecting piece 3 S3 1 Connecting piece 4 S4 1 Bracket 1 T1 1 Bracket 2 T2 1 Bracket 3 T3 4 Corner support U 2 Sidestay1 V1 2 Sidestay2 V2 2 Sidestay3 V3 1 Sidestay4 V4 1 Curtain W 1 Mosquito Net Y 1 Hardware Pack 1 AA Bolt M6X20 4PCS BB Flat washer M6 74PCS CC Bolt M6X15 38PCS DD Nut M6 2PCS EE Plastic ring 80PCS FF Bolt M6X15 24PCS GG Bolt M6X35 4PCS HH Bolt M6X15 26PCS Z1 Wrench M6 2PC Z2 Wrench M6 1PC
Fig.1: Install the curtain-mounting tab (Q) to back post 1 (A3) and back post 2 (A4) with bolt (AA) and flat washer (BB). Ensure the narrow surface of the curtain-mounting tab (Q) faces the post with three holes. Fig.2: Set the post base cover 1 (P1) into the back post 1(A3)and back post 2 (A4), then secure post base 1 (O1) to post 4 (A4) and post 3 (A3) with a bolt (HH) and flat washer (BB). Ensure the flat surface of the base 1 (O1) and post base cover 1 (P1) face the post with three holes. Fig.
Fig.4-1: Insert the junction bar (D) into the decorative slot 1(C1) and decorative slot 2 (C2), and secure with bolt (CC) and flat washer (BB). Fig.5: Install the plastic rings (EE) into the runner of side beam 1 (B1) and side beam 2 (B2), 12 plastic rings for each runner. There are 2 Plastic rings to be each inside corner Fig.6: Insert the beam junction (F) into back beam 1 (E1) and beam 2 (E2) and secure with bolt (CC), and flat washer (BB).
Hardware Pack 2 BB Flat washer M6 56PCS CC Bolt M6X15 40PCS DD Nut M6 4PCS II Nut M6 12PCS Fig.13, Fig.13-1: Insert the PC panel 3 (M3)(or PC panel 5 (M5)) to the card slot of edge beam and side beam, then insert PC panel 2 (M2)(or PC panel 4(M4)) to the card slot of edge seam and side beam. Fig.14: Using connecting piece 1 (S1), bolt (CC) and flat washer (BB) to install one side of middle beam (L3) to back beam. Fig.
Fig.14-3: Install another side of middle beam (L3) to decorative slot by using connecting piece 1(S1), bolt (CC) and flat washer (BB). Fig.15: Insert the small beam junction (I) into small beam 1(H1) and small beam 2(H2) and secure them with bolt CC and flat washer BB. Fig.15-1: Set the complete small beam through the 2 group bolts middle beam (L3) and edge beam(L1) and secure them with nut (II) and flat washer (BB).
Fig.16: Settle back card slot 1 (J1) and back card slot 2 (J2) to edge beam and middle beam, and secure one side of back card slot to edge beam by using bolt (HH) and flat washer (BB). Fig.16-1: Fix Back card slot 1(J1) and Back card slot 2 (J2) with Middle beam (L3). Fig.17: Set the side card slot 1 (N1) and side card slot 2 (N2) to side PC panel, and secure them with bolt HH and flat washer BB. Fig.
Fig.21-1: Attached Side stay (V1, V2) to Post (A1, A2) with Bolt (CC) and Flat Washer (BB). Fig.21-2: Slid 1pc Plastic Ring (EE) to be inside of Stay 1(V1), then use Bolt (GG) and Washer (BB) to lock top of Side Stay 1(V1), Decorative slot 1(C1) and Side beam 2(B2) together. Repeat this step, lock Side Stay 2 (V2), Decorative slot 2(C2) and Side beam 1(B1) together. Fig.21-4: Use Bolt (GG) and Washer (BB) to lock Side Stay (V4, V3) onto Back beam (E1, E2). Fig.
Care & Maintenance: Our steel components for garden accessories and furniture are treated with rust inhibiting paint that protects it from rusting. However, due to the nature of steel, surface oxidation (rusting) will occur once these protective coatings are scratched. This is not a defect and thus not covered by the warranty. To minimize this condition, we recommend care when assembling & handling the product to prevent scratching the paint.