ASSEMBLY INSTRUCTION Item#:L-GZ636PST-B
SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate or install the product. WARNING This product is intended for outdoor use only and should be placed on flat, horizontal ground. Ensure enough clearance around the product. Anchor the gazebo to the ground with stakes for added safety. Stakes are provided to secure the gazebo in the ground.
Parts List Post A 4 Top Screen 1 B 4 Top Screen 2 C 4 Big Top Slanting Bar D 4 Big Top Beam E 4 F 4 Big Top Beam Connector G 4 Big Top Bar H 4 Big Top Connector I 4 Big Roof Top Beam 1 (left) J1 4 J2 4 J3 4 J4 4 Small Roof Top Beam J5 4 Small Top Support Bar K1 4 Big Top Left Support Bar K2 4 Big Top Right Support Bar K3 4 Small Top Slanting Bar M 4 Big Top Slanting Bar Connector Big Roof Top Beam 1 (right) Big Roof Top Beam 2 (left) Big Roof Top Beam 2 (ri
Small Top Cover O 1 Hook P 1 Small Top Connector Q 1 Small Top Roof Panel R1 4 Big Top Roof Panel 1 R2 4 Big Top Roof Panel 2 R3 4 Small Top Cover 1 S1 4 Big Roof Panel Cover 1 S2 4 Big Roof Panel Cover 2 S3 4 Small Top Cover 2 T2 4 Big Roof Panel Cover 3 T3 4 Big Roof Panel Cover 4 T4 8 Hardware Pack 1 AA M6*15 Bolt 44 BB M6 Flat Washer 44 ZZ M6 Wrench 2
1. Insert the Top Screen 2 2. Attach the Big Top Slanting 3. Attach the assembled (C) into the Top Screen 1 (B), Bar Connector (F) to the Post screens (B、C) to the Post (A) and then install the Big Top (A) with Bolts (AA) and Flat with Bolts (AA) and Flat Beam Connector (G) onto Washers (BB). Washers (BB). the screens and securing with Bolts (AA) and Flat Washers (BB).
Hardware Pack 2 AA M6*15 Bolt 44 PCS BB M6 Flat Washer 68 PCS DD M6*55 Screw 12 PCS EE M6 Nut 12 PCS 4. Insert the Big Top Bar (H) 5. Attach the Big Top Slanting 6. Attach the Big Top Slanting into the Big Top Connector Bar (D) to the Big Top Bar (D) to the Big Top (I) and securing with Bolts Connector (I) with Bolts (AA) Slanting Bar Connector (F) (AA) and Flat Washers (BB). and Flat Washers (BB). with Screws (DD), Nuts (EE) and Flat Washers (BB).
. 7.Attach Attachthe theBig BigTop TopBeam Beam 8. Attach the Big Top Beam 9. Attach the Small Top Slanting Bar (E) (E)to tothe theBig BigTop TopBar Bar(H) (H) (E) to the Big Top Beam (M) to the Small Top Connector (Q) with withBolts Bolts(AA) (AA)and andFlat Flat Connector (G) with Screws with Screws (DD), Nuts (EE) and Washers Washers(BB). (BB). (DD) , Nuts (EE) and Flat Flat Washers (BB). Then attach the Washers (BB).
13. Put the Small Top Roof Panel 14. Attach the Small Top 15. Attach the Small Top (R1) onto the small top and put Cover 1 (S1) to the Small Cover (O) to the Small Top the Small Top Cover 2 (T2) onto Top Slanting Bar (M) with with Nut (II). the Small Top Roof Panel (R1), Screws (GG) and Flat then attach both of them (R1 & Washers (BB). T2) to the Small Top Support Bar (K1) with Screws (FF) and Flat Washers (BB). 16. Attach the Big Roof Top Beam 17. Attach the Big Roof Top Beam 18.
19. Attach the Big Top Left Support Bar (K2) and the Big Top Right Support Bar (K3) to the Big Top Slanting Bar (D) with Bolts (AA) and Flat Washers (BB).
20. Put the Big Top Roof 21. Put the Big Roof Panel 22.
Always disassemble the gazebo completely. A partially disassembled gazebo is not stable enough to resist wind and bad weather, and therefore can be damaged and/or cause damage. Do not use bleach, acid or other abrasive cleaners on the roof or frame parts. Steel components of garden accessories and furniture are treated with rust-inhibiting paint. However, due to the nature of steel, surface oxidation (rusting) will occur if this protective coating is scratched. This is a natural process.
