User's Manual
Table Of Contents
- 1 About this Manual
- 2 Safety Instructions
- 3 Product Introduction
- 4 Installation Flow
- 5 Unpacking and Storage
- 6 Mechanical Installation
- 7 Electrical Connection
- 7.1 Safety Instructions
- 7.2 Port Introduction
- 7.3 Overview
- 7.4 Connecting to the Inverter
- 7.5 Connecting to the Meteo Station
- 7.6 Connecting to the Energy Meter
- 7.7 Wiring of DI Signal
- 7.8 Wiring of DO Signal
- 7.9 Wiring of AI Signal
- 7.10 Wiring of PT Signal
- 7.11 Connecting to the Remote Monitoring Device
- 7.12 Connecting to the AC Power Supply
- 7.13 Connecting to the DC Power Supply
- 7.14 Earthing Connection
- 8 Commissioning
- 9 Web Interface
- 9.1 Running Requirements
- 9.2 Login Steps
- 9.3 Web Main Interface
- 9.4 Operation Procedure
- 9.5 Overview
- 9.6 Device Monitoring
- 9.7 Device Maintenance
- 9.8 History Data
- 9.9 System
- 9.9.1 Running Information
- 9.9.2 System upgrade
- 9.9.3 Log export
- 9.9.4 Rebooting
- 9.9.5 Reset all setting
- 9.9.6 Remote Maintenance
- 9.9.7 Message Export
- 9.9.8 System Time
- 9.9.9 Forwarding Configuration
- 9.9.10 IEC104
- 9.9.11 MODBUS
- 9.9.12 Third-party portal
- 9.9.13 Forward GOOSE Service Configuration
- 9.9.14 Interface
- 9.9.15 MPLC
- 9.9.16 More
- 9.9.17 About
- 10 Grid Dispatching
- 11 Maintenance
- 12 Troubleshooting
- 13 FAQ
- 14 Appendix A: Technical Data
- 15 Appendix B: Related Drawings
- 16 Appendix C: General Information
62
9.9.14.2 Ethernet
Perform Ethernet settings on this interface.
step 1 Click "System" -> "Interface" -> "Ethernet" to enter the corresponding interface.
step 2 If auto IP allocation is
, the IP address of port ETH in invalid. Log in to the device
using the virtual IP address.
PPoorrtt
DDeeffaauulltt IIPP
VViirrttuuaall IIPP
ETH 12.12.12.12 14.14.14.14
step 3 If the parameter "Automatically obtain IP settings (DHCP)" is set to
, fill in the
information such as the IP address, subnet mask, and default gateway, and click the
button
to save the operation.
-- -- EEnndd
9.9.14.3 AI
step 1 Click "System" -> "Interface" -> "AI" to enter the corresponding interface.
step 2 Select an input type, set the lower limit and upper limit, and click the button
to save
the operation.
AAII PPoorrtt
IInnppuutt TTyyppee
LLoowweerr SSaammpplliinngg
LLiimmiitt
UUppppeerr SSaammpplliinngg
LLiimmiitt
AI1
Voltage (V)
0 10
AI2
Current (mA)
4 20
AI3
Current (mA)
4 20
AI4
Current (mA)
4 20
step 3 If there is an external IO device connected to the logger, click “External” to set the AI
information of this device.
-- -- EEnndd
9.9.14.4 DI
step 1 Click "System" -> "Interface" -> "DI" to enter the corresponding interface.
step 2 Set the initial status to "NO" or "NC", and click the button
to save the operation.
step 3 If there is an external IO device connected to the logger, click “External” to set the DI
information of this device.
-- -- EEnndd
9.9.14.5 DO
step 1 Click "System"->"Port Parameter"->"DO" to enter the "Built-in" interface.
9 Web Interface User Manual