User's Manual
Table Of Contents
- 1 About this Manual
- 2 Safety Instructions
- 3 Product Introduction
- 4 Installation Flow
- 5 Unpacking and Storage
- 6 Mechanical Installation
- 7 Electrical Connection
- 7.1 Safety Instructions
- 7.2 Port Introduction
- 7.3 Overview
- 7.4 Connecting to the Inverter
- 7.5 Connecting to the Meteo Station
- 7.6 Connecting to the Energy Meter
- 7.7 Wiring of DI Signal
- 7.8 Wiring of DO Signal
- 7.9 Wiring of AI Signal
- 7.10 Wiring of PT Signal
- 7.11 Connecting to the Remote Monitoring Device
- 7.12 Connecting to the AC Power Supply
- 7.13 Connecting to the DC Power Supply
- 7.14 Earthing Connection
- 8 Commissioning
- 9 Web Interface
- 9.1 Running Requirements
- 9.2 Login Steps
- 9.3 Web Main Interface
- 9.4 Operation Procedure
- 9.5 Overview
- 9.6 Device Monitoring
- 9.7 Device Maintenance
- 9.8 History Data
- 9.9 System
- 9.9.1 Running Information
- 9.9.2 System upgrade
- 9.9.3 Log export
- 9.9.4 Rebooting
- 9.9.5 Reset all setting
- 9.9.6 Remote Maintenance
- 9.9.7 Message Export
- 9.9.8 System Time
- 9.9.9 Forwarding Configuration
- 9.9.10 IEC104
- 9.9.11 MODBUS
- 9.9.12 Third-party portal
- 9.9.13 Forward GOOSE Service Configuration
- 9.9.14 Interface
- 9.9.15 MPLC
- 9.9.16 More
- 9.9.17 About
- 10 Grid Dispatching
- 11 Maintenance
- 12 Troubleshooting
- 13 FAQ
- 14 Appendix A: Technical Data
- 15 Appendix B: Related Drawings
- 16 Appendix C: General Information
50
9.6.9 General Parameters
step 1 Click “Device Monitoring” -> “General Parameters” to enter the interface and set
general parameters of the device.
step 2 Select "Read-back", set "Register Address", " Register Number" and "Address Type",
and click [Read-back]. The current value of the device can be read.
step 3 Select "Settings", set "Register Address, "Data Type" and "Set Value".
• Set general parameters for a single device: Click 【Settings】 to complete the
Settings.
• Configure general parameters for multiple devices: Click 【Configure
Synchronization】to synchronize the settings to multiple devices.
-- -- EEnndd
9.6.10 Device Instruction
Click "Device monitoring" -> "Device instruction" to enter the corresponding interface.
On this interface, users can boot/shutdown the device or reset all settings.
Device instruction can be set in two manners: single setting and batch setting. Take the
boot operation as an example for explanation.
9.6.10.1 Single setting
step 1 Select a device, click “boot”, and a dialog box pops up.
step 2 Click “Yes” to start a single device.
-- -- EEnndd
9.6.10.2 Batch setting
step 1 Select a device, click “boot”, and a dialog box pops up.
step 2 Click "Configure synchronization".
step 3 Select the desired devices in the pop-up device list, and click "Save" to achieve batch
setting.
step 4 Click “Confirm” on the pop-up dialog box.
-- -- EEnndd
9.6.11 Device Information
Click "Device Monitoring" -> "Device Information" to view the corresponding information.
Parameter information such as device S/N, device model, and rated active power can
be viewed.
9 Web Interface User Manual