User's Manual
Table Of Contents
- 1 About this Manual
- 2 Safety Instructions
- 3 Product Introduction
- 4 Installation Flow
- 5 Unpacking and Storage
- 6 Mechanical Installation
- 7 Electrical Connection
- 7.1 Safety Instructions
- 7.2 Port Introduction
- 7.3 Overview
- 7.4 Connecting to the Inverter
- 7.5 Connecting to the Meteo Station
- 7.6 Connecting to the Energy Meter
- 7.7 Wiring of DI Signal
- 7.8 Wiring of DO Signal
- 7.9 Wiring of AI Signal
- 7.10 Wiring of PT Signal
- 7.11 Connecting to the Remote Monitoring Device
- 7.12 Connecting to the AC Power Supply
- 7.13 Connecting to the DC Power Supply
- 7.14 Earthing Connection
- 8 Commissioning
- 9 Web Interface
- 9.1 Running Requirements
- 9.2 Login Steps
- 9.3 Web Main Interface
- 9.4 Operation Procedure
- 9.5 Overview
- 9.6 Device Monitoring
- 9.7 Device Maintenance
- 9.8 History Data
- 9.9 System
- 9.9.1 Running Information
- 9.9.2 System upgrade
- 9.9.3 Log export
- 9.9.4 Rebooting
- 9.9.5 Reset all setting
- 9.9.6 Remote Maintenance
- 9.9.7 Message Export
- 9.9.8 System Time
- 9.9.9 Forwarding Configuration
- 9.9.10 IEC104
- 9.9.11 MODBUS
- 9.9.12 Third-party portal
- 9.9.13 Forward GOOSE Service Configuration
- 9.9.14 Interface
- 9.9.15 MPLC
- 9.9.16 More
- 9.9.17 About
- 10 Grid Dispatching
- 11 Maintenance
- 12 Troubleshooting
- 13 FAQ
- 14 Appendix A: Technical Data
- 15 Appendix B: Related Drawings
- 16 Appendix C: General Information
46
After logging into the Web, first configure the serial ports of the Logger4000, to ensure
that the Logger4000 can normally communicate with upstream devices. Refer to the
chapter"9.9.14 Interface".
step 2 Calibrate the system time.
Check whether the current system time is correct, and perform manual time
synchronization or automatic time synchronization when necessary. Refer to the
chapter"9.9.8 System Time".
step 3 Automatically search the device.
Devices that can be automatically searched, such as SUNGROW string inverter, can be
added via the auto search function with addresses allocated automatically. Refer to the
chapter "9.7.1 Device List".
step 4 Add the device. Refer to the chapter
"9.7.1 Device List".
step 5 Configure forwarding service.
After all devices have been added, configure the forwarding service of the Logger4000,
to ensure that the Logger4000 can forward the data to upstream devices. Refer to the
chapter"9.9.9 Forwarding Configuration", "9.9.10 IEC104", "9.9.11 MODBUS", "9.9.12
Third-party portal","9.9.13 Forward GOOSE Service Configuration".
-- -- EEnndd
9.5 Overview
9.5.1 General Information
Click "Overview" -> "General information" to enter the corresponding interface.
SShhoorrttccuutt MMeennuu
• Device setup
Support of auto search and add device functions. Click the menu to add, delete,
modify, and view the device or perform auto search operation to search the device
to which address will be automatically allocated. Refer to the chapter "9.7.1 Device
List".
• Network management
Set Ethernet parameters. Refer to the chapter "9.9.14 Interface".
9 Web Interface User Manual