User Manual

ManualsBrandsSUNELL ManualsNetwork CameraSunell SN-IPV8040EFAR-B Vandal Dome Network Camera

Table Of Contents

NO:101-100-0517-02

Issue:1.2

Vandal Dome Network Camera

Quick Setup Guide

Special Announcement

For more information, please refer to website.

Fully understand this document before using this device, and

strictly observe rules in this document when using this device. If

you install this device in public places, provide the tip "You have

entered the area of electronic surveillance" in an eye-catching

place. Failure to correctly use electrical products may cause fire

and severe injuries.

It alerts you to moderate dangers which, if not

avoided, may cause minor or moderate injuries.

It alerts you to risks. Neglect of these risks may

cause device damage, data loss, device

performance deterioration, or unpredictable results.

It provides additional information.

Ÿ Strictly observe installation requirements when installing the

device. The manufacturer shall not be held responsible for

device damage caused by users' non-conformance to these

requirements.

Ÿ Strictly conform to local electrical safety standards and use

power adapters that are marked with the LPS standard when

installing and using this device. Otherwise, this device may be

damaged.

Ÿ Use accessories delivered with this device. The voltage must

meet input voltage requirements for this device.

Ÿ If this device is installed in places with unsteady voltage, ground

this device to discharge high energy such as electrical surges in

order to prevent the power supply from burning out.

Ÿ When this device is in use, ensure that no water or any liquid

flows into the device. If water or liquid unexpectedly flows into

the device, immediately power off the device and disconnect all

cables (such as power cables and network cables) from this

device.

Ÿ Do not focus strong light (such as lighted bulbs or sunlight) on

Ÿ Avoid heavy loads, intensive shakes, and soaking to prevent

damages during transportation and storage. The warranty does

not cover any device damage that is caused during secondary

packaging and transportation after the original packaging is

taken apart.

Ÿ Protect this device from fall-down and intensive strikes, keep

the device away from magnetic field interference, and do not

install the device in places with shaking surfaces or under

shocks.

Ÿ Clean the device with a soft dry cloth. For stubborn dirt, dip the

cloth into slight neutral cleanser, gently wipe the dirt with the

cloth, and then dry the device.

Ÿ Do not jam the ventilation opening. Follow the installation

instructions provided in this document when installing the

device.

Ÿ Keep the device away from heat sources such as radiators,

electric heaters, or other heat equipment.

Ÿ Keep the device away from moist, dusty, extremely hot or cold

places, or places with strong electric radiation.

Ÿ If the device is installed outdoors, take insect- and moisture-

proof measures to avoid circuit board corrosion that can affect

monitoring.

Ÿ Remove the power plug if the device is idle for a long time.

Ÿ All complete products sold by the manufacturer are delivered

along with nameplates, quick setup guide and accessories after

strict inspection. The manufacturer shall not be held

responsible for counterfeit products.

Ÿ The manufacturer will update this manual according to product

function enhancement or changes and regularly update the

software and hardware described in this manual. Update

information will be added to new versions of this manual without

prior notice.

Ÿ This manual may contain misprints, technology information that

is not accurate enough, or product function and operation

description that is slightly inconsistent with the actual product,

the final interpretation of company is as a standard.

Ÿ This manual is only for reference and does not ensure that the

information is totally consistent with the actual product. For

consistency, see the actual product.

Precautions

Open the package, check the appearance of product for no

obvious damage, and confirm the item list for table 1-1 is

consistent.

Table 1-1 Packing list

2.1 Device Ports

Component

Quantity

Remark

Vandal Dome Network Camera

Quick Setup Guide

T15 Screw driver

T10 Screw driver

Installation location sticker

Stainless self-tapping screw

Plastic anchor

Network access port protective cover

Waterproof rubber seal

Terminal block

Optional

Phillips stainless screw (install on bracket)

NOTE

this device. Otherwise, the service life of the image sensor may

be shortened.

Ÿ If this device is installed in places where thunder and lightning

frequently occur, ground the device nearby to discharge high

energy such as thunder strikes in order to prevent device

damage.

Figure2-2 Multi-head cable 1

Table 2-2 Multi-head cable description

2.2 Camera Dimensions

Figure 2-4 Dimensions of Mimi Dome（Unit:mm）

Different devices may have different dimensions; Please

refer to the actual product.

NOTE

CAUTION

WARNING

CAUTION

Open Package Examination

Device Structure

Large Dome

Mini Dome

Ø110

Ø100

28.8

120°

85.4

120°

Ø4.5

Figure 2-5 Dimensions of Large Dome(Unit:mm）

Len adjustment is only applied for large dome.

Figure 2-1 Lens adjustment

Port Name

Table 2-1 Lens adjustment description

Description

NOTE

Zoom lever

Focusing lever

Zoom lever

Adjust the focus of lens, the default status is lock.

Adjust the lens focal length, the default status is

lock.

Table 2-3 Multi-head cable 2 description

Different devices may have different multi-heads; Please

refer to the actual product.

NOTE

Figure2-3 Multi-head cable 2

3（Some models

may not have）

Reset

Powe r

Network

access port

Connects to a standard Ethernet cable or

PoE . The green light is on, the network

connection is normal; the yellow light

flashes when the data is transmitted.

Some models maybe not have the lights;

Please refer to the actual product.

Support

PoE

supply.

Connects to a 12V direct current (DC)

power supply.

Core

Description

Remark

Reset button

Power supply

(DC 12V)

Long press the button for 5 seconds to

restore the original settings.

Reset

Por t

OUT

Connects to a standard Ethernet

cable or PoE . The green light is on,

the network connection is normal;

the yellow light flashes when the

data is transmitted. Some models

maybe not have the lights; Please

refer to the actual product.

Connects to an external audio

device such as a speaker.

Applied for

camera with

audio

function

Receives an analog audio signal

from devices such as a sound

pickup device.

Long press the reset button for 5

seconds to restore the original

settings.

Connects to a 12V direct current

(DC) power supply.

Alarm output COM

Applied for

alarm

function

Alarm output terminal

Alarm input COM

Alarm input terminal

Network

access port

Support PoE

supply.

Core

Description

Remark

Audio output

Power supply

(DC 12V)

Audio input

port

Reset botton

OUT

Orange

: Alar

m COM0

Yellow: Alarm IN0

Grey

: Alarm OUT1

Purple

: Alarm

COM1

Type1

Some models’ alarm cable

maybe show this type.

Summary of content (2 pages)

PAGE 1
this device. Otherwise, the service life of the image sensor may be shortened. Ÿ If this device is installed in places where thunder and lightning frequently occur, ground the device nearby to discharge high energy such as thunder strikes in order to prevent device damage. CAUTION Ÿ Avoid heavy loads, intensive shakes, and soaking to prevent Ÿ Ÿ Ÿ Ÿ Ÿ Open the package, check the appearance of product for no obvious damage, and confirm the item list for table 1-1 is consistent.
PAGE 2
19.3 40 112.24 10 0.0 137.0° 0° 3. Large dome To avoid moisture influence, install the dome cover at least half an hour after the camera is installed and powered on. The vandal dome camera can be installed in the ceiling , wall , wall bracket or ceiling bracket. This section describes how to install the camera in the ceiling. Installation Steps: Step 1 Use the T screw driver in the accessory package to unscrew the three screws on the dome cover. The camera is opened, as shown in figure 3-1.