FOSSIL 5-Piece Round Sectional Set Assembly tip: Do not tighten the screws iW fully until each of them is aligned.
FO8LN940 5-Piece Round Sectional Set Assembly tip: Do not tighten the screws fully until each of them is aligned. tom Rena Description | Qty. Al Far Right Back | 1 A2 Far Left Back | 1 B1 Right Middle Back Lat Middle Back Left Side Panel Right Side Panel | 1 D | Base Panel Side Base Side Base Fasteners Fasteners | 4 M6*15 Socket R # M6*15 |Head Cap Screw 16 M6*35 Socket Ss A M635 |Head Cap Screw 12 M650 Socket T ” M6%50 | Head Cap Screw 5 U Flat Washers Nut 5 Step 1:Position in order.
FO8LN940 5-Piece Round Sectional Set Assembly tip: Do not tighten the screws fully until each of them is aligned. Step 2:Attach the Right Side Panel (C2) to the assembly (A1) using an M635 socket head cap screw (S) with a flat washer (U). DO this in two places. Step 3:Attach the Side Base (E1} to the assembly (C2) using an M6*35 socket head cap screw {S) with a flat washer (U). DO this in two places.
FO8LN940 5-Piece Round Sectional Set Assembly tip: Do not tighten the screws fully until each of them is aligned. rem tan Description | Qty. F | = |ShortestLowestBar | 2 G 2nd Shortest 2nd 2 | Lowest Bar H 2nd Longest 2nd Highest Bar | | seem.
FO8LN940 5-Piece Round Sectional Set Assembly tip: Do not tighten the screws fully until each of them is aligned. Step 4:Attach the extender (W) to the daybed. The thicker end of the extender should be close to the base of the daybed. Thread the M6*15 socket head cap screws(R} with a washer(U), the insert of the extender (W) followed by a spacer (X). Connect this to the extra holes on poles (F) and (I) . Do this on both sides. Step 5:Secure pole (1} to the top holes on the outside of the daybed .
FO8LN940 5-Piece Round Sectional Set Assembly tip: Do not tighten the screws fully until each of them is aligned. rom tan Description | Qty. Base Panel Outside Panel Side Panel Inside Panel | 2 M635 Socket S A M6%35 | Head Cap Screw 26 M6*50 Socket T ” M650 | Head Cap Screw| 4 ) 1) Flat Washers Nut 4 Step 1:Connect the two outside panels(M), using the M6*50 Socket Head Cap Screw (T) with Flat Washers (U) and a nut (V) with Flat the Allen key and wrench to tighten. Do this in two places.
FO8LN940 5-Piece Round Sectional Set Assembly tip: Do not tighten the screws fully until each of them is aligned. tem Rene Description Qty. K 5 Top of Base Side Base | 3 M6*35 Socket S » M6%35 (Head Cap Screw 3 M6*50 Socket T ” M6#50 |Head Cap Screw| © U Flat Washers| 15 Vv M6 Nut 6 Y | 4mm Allen Key| 1 Z| S— Wrench | 1 Step 1:Attach the top of base (K) to side base using M635 Socket Head Cap Screw(S) and flat Washers this in three places.
FOBBING 5-Piece Round Sectional Set Assembly tip: Do not tighten the screws fully until each of them is aligned. ! CAUTION In order for the Beauty of sofa appearance, the back cover is designed to be a bit tight which may cause some difficulties in installation.To prevent the cover being ripped, you are recommended to put the cushion onto the setback from both sides slowly while assembling.
