Sunbeam Tower Fan with Remote Control Instruction Booklet FA7450 99cm Tower Fan Please read these instructions carefully and retain for future reference.
Contents Sunbeams Safety Precautions 1 Safety Precautions For Your Tower Fan 2 Locating Your Tower Fan 3 Features of Your Tower Fan 4 Assembling Your Tower Fan 5 Remote Control 6 Using Your Tower Fan 7 Troubleshooting Guide 11 Care And Cleaning 11 Important instructions – retain for future use.
Sunbeam’s Safety Precautions • • • • • • • • • Sunbeam is very safety conscious when designing and manufacturing consumer products, but it is essential that the product user also exercise care when using an electrical appliance. Listed below are important precautions for the safe use of an electrical appliance. Read carefully and save all the instructions provided with an appliance. Always turn the power off at the power outlet before you insert or remove a plug.
Safety Precautions For Your Tower Fan • Do not use outdoors. • Do not run the cord of the fan under carpeting. Do not cover the cord with throw rugs, runners or other floor coverings. Arrange the cord away from traffic areas so that it will not be tripped over. • Do not use this fan in the immediate surrounds of a bath, shower, laundry area or swimming pool. • Be sure the fan is placed on a dry, even surface. Do not use on soft surfaces, such as beds, where opening may become blocked.
Locating Your Tower Fan 1. Always locate your fan on a level surface. 2. Your tower fan should be located in a dry, cool, well ventilated location. Keep your fan away from heat sources, corrosive gases and avoid direct sunlight. 3. Do not attempt to move your tower fan whilst it is operating. If your fan needs to be moved, please ensure that it is turned off and you use the carry handle on top of the fan.
Features Of Your Sunbeam Tower Fan Carry handle Convenient carry handle allows you to easily carry your fan from room to room. Control Panel Simply press the on/off button to turn the unit on. Use the other buttons to select wind mode, timer, speed and oscillation functions. Indication Panel The indication panel allows you to quickly see which functions have been selected on your tower fan.
Assembling Your Tower Fan 1. Locate the two halves of the base. 2. Remove the two butterfly screws from underneath the tower section of the fan and set aside. 3. Feed the power cord between the two halves of the base. See Figure 1. 6. Feed the power cord through the two guides on the bottom of the base; the cord will then come out through the outer rim. 7. Insert the 4 silicon feet provided into the holes under the base. 8. Stand the fan upright, it is now ready for use. See Figure 3.
Remote Control Remote control Operates within 8 metres of the Tower Fan. Fan speed button Choose from 3 speed settings, low medium or high. Wind Mode You have a choice of 2 Nature or Sleep airflow types. When used in nature mode, the fan speed is randomly adjusted, giving the feeling of a natural breeze. When set to Sleep Mode the fan speed decreases after 30 minutes from high to medium, then medium to low. When used with the timer, will ultimately switch the unit off. Using the remote control 1.
Using Your Tower Fan Switching the fan on 1. Place the fan on a level surface. 2. Insert the plug into a 230/240V power outlet and turn the power on. 3. Press the power button on/off. 4. Press the fan speed button to select low, medium or high depending on your preference. Switching the fan off • To switch the fan off, simply press the power button on/off . • If you will not be using the fan for a length of time, it is advisable to turn the power off at the wall socket and unplug the power cord.
Using Your Tower Fan (continued) Using the oscillation function The 70 degree oscillation function can be used on any setting. 1. Turn the unit on and select any fan speed. 2. Press the ‘OSC’ button on the tower or the remote. The fan will begin to oscillate from side to side. To stop the fan from oscillating, simply press the ‘OSC’ button once again. 8 Using the preset timer To set the Timer to turn off 1. Press the on/off button. 2.
Using Your Tower Fan (continued) To set the Timer to turn on 1. With the fan off, but on at the power outlet (Standby mode) continuously press the Preset/Timer button first to select the desired time. 2. You can also select the wind speed, wind mode and oscillation options once the preset time has been selected.
Using Your Tower Fan (continued) WIND MODES Nature mode Nature mode provides an extra level of comfort by simulating the natural rise and fall of the wind over time. You can use this mode on any fan speed setting. To use Nature mode: 1. Choose a fan speed. 2. Press the button on either the tower or the remote until the light illuminates. The fan will now vary its speed every few seconds between the chosen fan speed, each lower fan speed, and off.
Troubleshooting Guide If your tower fan fails to operate check the following: • Make sure the electrical outlet or circuit breaker is working. • Check for obstructions around the air intake grill. If your remote control fails to operate check the following: • Ensure that you point the remote towards the front of the fan. • Check that the batteries are not worn. Replace if necessary. Care and Cleaning Ensure that your fan is switched off and disconnected from the power outlet before cleaning.
Notes
2 Year Replacement Guarantee In the unlikely event that this appliance develops any malfunction within 2 years of purchase (3 months commercial use) due to faulty materials or manufacture, we will replace it for you free of charge. Should you experience any difficulties with your appliance, please phone our customer service line for advice on 1300 881 861 in Australia, or 0800 786 232 in New Zealand. Alternatively, you can send a written claim to Sunbeam at the address listed below.
Need help with your appliance? Contact our customer service team or visit our website for information and tips on getting the most from your appliance. In Australia Visit www.sunbeam.com.au Or call 1300 881 861 In New Zealand Visit www.sunbeam.co.nz Or call 0800 786 232 is a registered trademark. Made in China. Due to minor changes in design or otherwise, the product may differ from the one shown in this leaflet. © Copyright. Sunbeam Corporation Limited 2008.
