Ultra™ Enterprise™ 6000/5000/4000 Systems Installation Guide The Network Is the Computer™ Sun Microsystems Computer Company 2550 Garcia Avenue Mountain View, CA 94043 USA 415 960-1300 fax 415 969-9131 Part No.
Copyright 1996 Sun Microsystems, Inc. 2550 Garcia Avenue, Mountain View, California 94043-1100 U.S.A. All rights reserved. This product or document is protected by copyright and distributed under licenses restricting its use, copying, distribution, and decompilation. No part of this product or document may be reproduced in any form by any means without prior written authorization of Sun and its licensors, if any. Portions of this product may be derived from the UNIX® system and from the Berkeley 4.
Contents 1. Preparing for Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 1.1 Unpacking the Enterprise 6000/5000 Cabinet Systems . . 1-3 1.2 Shipping and Storing the System . . . . . . . . . . . . . . . . . . . . 1-4 1.3 Preparing the Electrical Circuits . . . . . . . . . . . . . . . . . . . . . 1-5 1.3.1 Enterprise 6000/5000 Cabinet Systems . . . . . . . . . . 1-5 1.3.2 Enterprise 4000 System. . . . . . . . . . . . . . . . . . . . . . . . 1-7 1.
1.9 Using the User Naming Area . . . . . . . . . . . . . . . . . . . . . . . 1-15 2. Cabling the System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 2.1 Preparing the System for Cabling. . . . . . . . . . . . . . . . . . . . 2-1 2.2 Removing and Replacing the Enterprise 6000/5000 Cabinet Rear Screen and Kick Panel . . . . . . . . . . . . . . . . . 2-1 2.3 Connecting the Power Cords . . . . . . . . . . . . . . . . . . . . . . . 2-4 2.3.
3.3.3 Interpreting Status LED Patterns . . . . . . . . . . . . . . . 3-13 3.3.4 Powering Off the System . . . . . . . . . . . . . . . . . . . . . . 3-15 3.4 Failure of Network Communications . . . . . . . . . . . . . . . . 3-16 4. Using the Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 4.1 Operating System Software. . . . . . . . . . . . . . . . . . . . . . . . . 4-1 4.2 Solstice SyMON Software . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 Index . . . .
vi Ultra Enterprise 6000/5000/4000 Systems Installation Guide—November 1996
Figures Figure 1-1 Ultra Enterprise 6000/5000/4000 Systems . . . . . . . . . . . . . . . . 1-2 Figure 1-2 Attaching the Ramps to the Shipping Pallet . . . . . . . . . . . . . . . 1-4 Figure 1-3 NEMA L6-30P Electrical Connector . . . . . . . . . . . . . . . . . . . . . . 1-5 Figure 1-4 IEC 309 Electrical Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6 Figure 1-5 Types of Network Cables Used . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 2-6 Network Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6 Figure 2-7 10/100BASE-T Ethernet Connection . . . . . . . . . . . . . . . . . . . . . 2-7 Figure 2-8 Connecting Twisted Pair Ethernet to N-type Coaxial Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8 Ethernet Cabling Length — Example Using N-type Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tables Table 2-1 Ethernet Cabling Limitations for N-type Coaxial Cable . . . . . 2-9 Table 2-2 Internal SCSI Lengths (Approximate) . . . . . . . . . . . . . . . . . . . . 2-13 Table 3-1 Front Panel LED Status Indicators . . . . . . . . . . . . . . . . . . . . . . . 3-8 Table 3-2 Front Panel LED System Status . . . . . . . . . . . . . . . . . . . . . . . . . .
x Ultra Enterprise 6000/5000/4000 Systems Installation Guide—November 1996
Preface The Ultra™ Enterprise™ 6000/5000/4000 Systems Installation Guide provides installation instructions for factory-configured 16-slot and 8-slot cabinet and standalone server systems. These instructions are for an experienced system administrator with networking knowledge. UNIX Commands This document may not include specific software commands or procedures. Instead, it may name software tasks and refer you to operating system documentation or the handbook that was shipped with your new hardware.
Typographic Conventions The following table describes the typographic changes used in this book. Typeface or Symbol Meaning Example AaBbCc123 The names of commands, files, and directories; on-screen computer output Edit your .login file. Use ls -a to list all files. machine_name% You have mail. AaBbCc123 What you type, contrasted with on-screen computer output AaBbCc123 Command-line placeholder: replace with a real name or value To delete a file, type rm filename.
Related Documents The following documents contain topics that relate to the information in the Ultra Enterprise 6000/5000/4000 Systems Installation Guide.
Germany 01-30-81-61-91 01-30-81-61-92 The Netherlands 06-022-34-45 06-022-34-46 Sweden 020-79-57-26 020-79-57-27 Switzerland 155-19-26 155-19-27 Japan 0120-33-9096 0120-33-9097 World Wide Web: http://www.sun.com/sunexpress/ Sun Welcomes Your Comments Please use the Reader Comment Card that accompanies this document. We are interested in improving our documentation and welcome your comments and suggestions. If a card is not available, you can email or fax your comments to us.
Procedures contained in this document must be performed by qualified service-trained maintenance providers. Note – Before you begin, carefully read each of the procedures in this manual. If you have not performed similar operations on comparable equipment, do not attempt to perform these procedures.
xvi Ultra Enterprise 6000/5000/4000 Systems Installation Guide—November 1996
Preparing for Installation 1 This chapter describes how to prepare your site for these systems: • • • Ultra Enterprise 6000 system — 16-slot cabinet server Ultra Enterprise 5000 system — 8-slot cabinet server Ultra Enterprise 4000 system — 8-slot standalone server See Figure 1-1 on page 1-2 for diagrams of the cabinet and standalone servers. The tasks for installing the systems are: 1. Unpacking the cabinet server — Chapter 1 2. Preparing the site — Chapter 1 3. Preparing the servers — Chapter 1 4.
1 Enterprise 6000/5000 systems — 16-slot and 8-slot servers in data center system cabinets Figure 1-1 1-2 Enterprise 4000 system — 8-slot standalone server Ultra Enterprise 6000/5000/4000 Systems Ultra Enterprise 6000/5000/4000 Systems Installation Guide—November 1996
1 1.1 Unpacking the Enterprise 6000/5000 Cabinet Systems Note – Inspect all shipping cartons for evidence of physical damage. If a shipping carton is damaged, request that the carrier's agent be present when the carton is opened. Keep all contents and packing material for the agent's inspection. If you have a standalone Enterprise 4000 system, or the cabinet is already unpacked, go to Section 1.3, “Preparing the Electrical Circuits.
1 ! Caution – To prevent the cabinet from tipping over, push or pull only on the upper half of the cabinet. Adhesive strip Wheel guide Figure 1-2 Attaching the Ramps to the Shipping Pallet 1.2 Shipping and Storing the System Save the original shipping containers and packing materials in case you need to store or ship your system. If you cannot store the shipping materials, recycle or dispose of the materials properly. Consult your local recycling authority for information.
1 1.3 Preparing the Electrical Circuits In planning where to place your equipment, remember that each of the following items require access (by way of a separate power cord) to a power outlet: • • • Ultra Enterprise 6000/5000/4000 system External peripherals Monitor used for diagnostics 1.3.1 Enterprise 6000/5000 Cabinet Systems The 16-slot and 8-slot system cabinets require a 30A circuit and a detachable cable.
1 Figure 1-4 IEC 309 Electrical Connector Note – If the appropriate mating receptacle is not available in your country, the plug may be removed from the cord. The cord can then be permanently connected to a dedicated branch circuit by a qualified electrician. Check local electrical codes for proper installation requirements. Warning – The system cabinet has a high leakage current to ground. Strictly observe the following instructions to reduce the risk of electric shock.
1 ! Caution – Do not make mechanical or electrical modifications to the server cabinet. Sun Microsystems® is not responsible for the regulatory compliance if the cabinet is modified. 1.3.2 Enterprise 4000 System The 8-slot Enterprise 4000 system uses nominal input voltages of 100-120 VAC or 200-240 VAC. Sun products are designed to work with single-phase power systems having a grounded neutral conductor. To reduce the risk of electrical shock, do not plug Sun products into another type of power source.
1 Set up the network using Sun or third-party components. To obtain the best results, read any applicable manufacturer instructions. Be aware that Sun Microsystems cannot guarantee the performance of any components that are not purchased from Sun.
1 Note – Multiplexer boxes require a transceiver when used with the Ethernet applications described in this manual. Although these transceivers are compatible with Sun equipment, Sun Microsystems does not guarantee the performance of any component that was not purchased from Sun. Many transceivers are compatible with both level-1 and level-2 Ethernet. To operate these transceivers with Sun equipment, set the device for level-2 operation following the manufacturer’s instructions.
1 3 feet access at rear 2 inches, left and right sides Tape/disk EXP Tape/disk EXP Tape/disk EXP System cabinet Tape/disk EXP Tape/disk EXP Tape/disk EXP 4 feet access at front Figure 1-7 Cabinet Server Access Areas — Top View 1.6.2 Surface for the Enterprise 4000 System The Enterprise 4000 system is designed to sit on the floor, on a caster base, or on a desk or table.
1 • Keep power and interface cables clear of foot traffic. Route cables inside walls, under the floor, through the ceiling, or in protective channels. Route interface cables away from motors and other sources of magnetic or radio frequency interference. 1.5 feet access at rear 6 inches* on each side Standalone system * 3 feet on each side if systems or peripherals are placed next to each other, side by side Figure 1-8 1.5 feet access at front Standalone Server Access Areas — Top View 1.
1 ! Caution – To prevent the cabinet from tipping over, push or pull only on the upper half of the cabinet. Figure 1-9 Moving the Server Safely Down the Ramps 1.7.2 Adjusting the Levelling Pads After moving the cabinet to its operating location, adjust the levelling pads. 1. Take off the rear screen by removing the two screws shown in Figure 1-10. Note – If your system cabinet has a hinged rear door, use the sliding door latch to open the door. 2.
1 3. Extend the stabilizer bar fully from the bottom of the cabinet. See Figure 1-11. 4. Screw the two stabilizer bar levelling pads down until they are 1/8- to 1/4-inch (three to six millimeters) above the floor. Make sure both pads are at equal heights above the floor. This clearance allows an extended stabilizer bar to stop the cabinet if it should begin to tilt. Rear screen Levelling pad (1 of 6) Kick panel Figure 1-10 Rear Screen, Levelling Wrench, Kick Panel, and Levelling Pad 5.
1 This completes the first part of the system installation. If you are unable to continue the installation at this time, close the cabinet: 1. Secure the levelling wrench inside the cabinet. 2. Replace the kick panel if the panel was removed. 3. Attach the rear screen. Stabilizer bar Figure 1-11 Stabilizer Bar 1.8 Preparing the Enterprise 4000 System ! Warning – The server weighs more than 150 lbs (68 kg). To prevent personal injury, two people are needed to lift the server safely.
1 • Front panel key (packed in a bag in the accessory box) Follow the graphic instructions on the shipping container to remove the server from the container. Remove the front panel key and the power cord from the shipping container. These are needed to power on the system. 1.9 Using the User Naming Area To display the name of the server, IP address, owner, or other important information on the front of the machine: 1. Remove the top front bezel.
1 1-16 Ultra Enterprise 6000/5000/4000 Systems Installation Guide—November 1996
2 Cabling the System This chapter contains procedures for connecting the power cord to the AC power supply and instructions for cabling the system to the network. 2.1 Preparing the System for Cabling Make sure the server is in an area that allows access to both the front and rear of the chassis. This site should conform to site preparation guidelines and specifications covered in Chapter 1. 2.
2 Standby position Figure 2-1 Keyswitch Standby Position 5. If the rear screen is still in place, remove it. Note – If your system cabinet has a hinged rear door, use the sliding door latch to open the door, and proceed to Step 6 and Step 7. a. Remove two screws near the top of the screen. See Figure 2-2. b. Tilt the screen out and lift it free of the chassis. Set the screen aside. 6. Remove the AC power cord that is coiled inside the server cabinet. Set the power cord aside. 7.
2 AC power sequencer Figure 2-2 Rear screen AC Power Sequencer Power Switch and Rear Screen Replacing the Rear Screen and Kick Panel 1. Tighten the two screws to secure the kick panel to the cabinet. If cables are to be routed under the floor, the cables should be between the bottom panel and the kick panel. See Figure 2-3. 2. Place the bottom of the rear screen on the flanges near the cabinet bottom. 3. Tilt the rear screen against the frame and install two screws to secure the screen in place.
2 Bottom panel Cable Kick panel Figure 2-3 Routing Cables Under the Kick Panel 2.3 Connecting the Power Cords 2.3.1 Connecting the Enterprise 6000/5000 System Power Cord 1. Remove the rear screen and the kick panel. See Section 2.2, “Removing and Replacing the Enterprise 6000/5000 Cabinet Rear Screen and Kick Panel.” 2. Route the AC power cord and external interface cables along the bottom panel of the cabinet and over the edge of the bottom panel. See Figure 2-3.
2 Warning – Risk of electric shock. Do NOT turn on AC power to the unit yet. 4. Continue with Section 2.4 through Section 2.7 for further cabling instructions, and then see Section 2.2 to replace the rear screen and kick panel. 2.3.2 Connecting the Enterprise 4000 System Power Cord 1. Insert the key provided with your system into the front panel key switch. Turn it to the Standby position (fully counterclockwise). See Figure 2-4. Standby Figure 2-4 Key Switch Positions 2.
2 AC connector AC power switch Figure 2-5 ! AC Power Switch and Power Receptacle Caution – Do NOT turn on power to the unit yet. Doing so could cause system damage to occur. 5. Continue with Section 2.4 through Section 2.7 for further cabling instructions. 6. After all the cables are connected, power on the system. 2.4 Connecting the Network Cable to the System The locations specified in the following instructions assume the use of twistedpair 10BASE-T or 100BASE-T Ethernet. 1.
2 2. Connect one end of the network cable into the RJ-45 twisted-pair network port. For 10/100BASE-T Ethernet, the default interface port is the onboard connector on the I/O board in slot 1. See Figure 2-7. Ethernet port Figure 2-7 10/100BASE-T Ethernet Connection 3. Enterprise 6000/5000 systems only: route the cable down along the right mounting rail of the chassis. Use tie wraps to secure the cable to the rail. 2.5 Connecting the System to the Network 1.
2 • If the Ethernet cable lacks N-type connectors at the ends, use a “vampire” tap to connect the cable to the transceiver. See Figure 2-8. To connect the cable to the transceiver, use instructions provided with the vampire tap. • If the Ethernet cable has N-type connectors, connect the Ethernet cable to the transceiver: a. Screw the Ethernet coaxial cable into one of the round screw-on type connectors on the transceiver. Use either one of the transceiver connectors. b.
2 Table 2-1 lists the cabling limitations for Ethernet. Table 2-1 Ethernet Cabling Limitations for N-type Coaxial Cable Cable Segment Length in Meters Allowed contiguous length of cable segments 23.4 70.2 117.0 500.01 2.52 Distance between transceivers (multiples-of) Minimum length of Ethernet coaxial cable segments 23.4 Maximum length of transceiver “drop” cable 50.0 Minimum length of twisted pair cable no minimum Maximum length of twisted pair cable 110 1.
2 Note – Sun equipment conforms to the Ethernet 10/100BASE-T standard, which states that the 10/100BASE-T Link Integrity Test function should always be enabled on both the host and the hub. If you have problems verifying connection between Sun equipment and your hub, verify that your hub also has the link test function enabled. See Section 3.4, “Failure of Network Communications,” and refer to the manual provided with your hub for more information about the Link Integrity Test function. 2.
2 2. Enterprise 6000/5000 systems only: route the terminal cable from the clock board down along the right mounting rail of the cabinet. Use tie wraps to secure the terminal cable to the mounting rail. 3. Connect the terminal power cord into an AC wall outlet. 4. Configure the ASCII terminal as follows: • 9600 bps • 1 stop bit • 8 data bits • Parity off • Full duplex Refer to the instruction manual shipped with the terminal for specific configuration instructions.
2 Notch on fiber cable Fibre card connector er Fib 1 Key notch in module connector er Fib 0 A B Connect cable through Port A (Fiber 0) or Port B (Fiber 1) Figure 2-11 Fiber Cable and Fibre Card Connectors and Ports on the I/O Board 2.8 Connecting External SCSI Devices External SCSI-2 devices connect to your system through the built-in singleended Fast/Wide SCSI-2 port on I/O boards (except for the board in slot 1), or through FSBE/S, DSBE/S, SWIS/S, or DWIS/S SBus cards installed on I/O boards.
2 Table 2-2 Internal SCSI Lengths (Approximate) Location Internal Length Comments Enterprise 6000 slot 1 3.7 meters Includes I/O board traces and cables to SCSI tray Enterprise 5000 slot 1 3.7 meters Includes I/O board traces and cables to SCSI tray Enterprise 4000 slot 1 1.4 meters Includes I/O board traces and cables to SCSI tray SBus I/O board 0.43 meter Includes board traces only Graphics I/O board 0.43 meter Includes board traces only Disk board 0.
2 Fast/wide onboard SCSI-2, 68-pin connector Figure 2-12 Onboard Single-ended SCSI Connector on the I/O Board 2. Enterprise 6000/5000 systems only: route the cable from the I/O board down along the left mounting rail inside the cabinet. Use tie wraps to secure the cable to the left mounting rail. 3. Connect the other end of the SCSI cable to the external SCSI-2 device. 4. Enterprise 6000/5000 systems only: return to Section 2.
Powering the System On and Off 3 This chapter contains information about powering the system on and off, reading boot messages, and interpreting system status by viewing the LEDs. 3.1 Using JumpStart Automatic Installation The Ultra Enterprise 6000/5000/4000 systems can use the JumpStart™ automatic installation feature that is described in installation documents for Solaris software.
3 Note – If JumpStart automatic installation begins unintentionally, interrupt it by pressing “L1-A” (Stop-A) or “Break” (on ttya). Perform a manual installation when you are ready. If JumpStart completes the installation incorrectly, you may need to reinstall Solaris 2.x manually. 3.2 Enterprise 6000/5000 Cabinet Systems 3.2.1 Powering On the System Note – It is advisable to connect an ASCII terminal to the system during installation. See Section 2.
3 On Legend: Diagnostics Standby Standby = OFF; no DC power On = Normal power ON Diagnostics = Normal power ON with full diagnostics Locked = Normal power ON in secure mode Locked Figure 3-1 ! Key Switch Positions Caution – The outlet must be a 200-240 VAC 30A circuit intended solely for use by the server cabinet. The electrical receptacles must be grounded, and the grounding conductors serving these receptacles must be connected to the earth ground at the service equipment.
3 AC power switch Figure 3-2 The AC Power Sequencer Power Switch 3. Turn on power to the terminal (if applicable). 4. Set the system cabinet Local/Remote switch to Local. See Figure 3-3. 5. Turn the AC power sequencer power switch to On. See Figure 3-2. Listen for the sound of AC-powered devices such as disk drives and fans in the disk drive tray(s).
3 Note – The front panel keys for this switch are packed in the accessory box. Local/remote switch Figure 3-3 Local/Remote Switch 6. Turn the key switch to the On position. The system will run firmware diagnostics for about one minute and then boot. You should see and hear several things happen: • The fans in the power supplies begin turning. • The left LED (green) on the front of the cabinet turns on immediately to indicate the DC power supply is functioning. • The middle LED (yellow) begins flashing.
3 • The right LED (green) flashes after firmware completes to denote that the operating system is running. • The terminal screen lights up upon completion of the internal self test. 7. Watch the terminal screen for any firmware error messages. Note – If the middle front panel LED remains lit after the system has booted, firmware has found (and deconfigured) failing hardware in the main cabinet. POST (power-on-self test) tests subassemblies and some interface paths between subassemblies.
3 System reset switch CPU reset switch Figure 3-4 CPU Reset Switch on the Clock Board 3.2.2 Reading Boot Messages Use the boot software messages to verify that all options are installed and recognized by the system. After firmware completes the system self test, a message similar to the following will appear on your screen. The message lists hardware detected in the system. Note – This screen display is an example only.
3 Note – When the system finishes booting for the first time — if there is no appropriate server configuration file on the disk drive — it may be necessary to prevent the JumpStart automatic configuration program from running. See the caution in Section 3.1, “Using JumpStart Automatic Installation.” 3.2.3 Interpreting Status LED Patterns If there is no terminal on the system, basic system status information is available on the front panel LEDs, as shown in Figure 3-5.
3 3.2.4 Powering Off the System Before turning off the system power, you must halt the operating system. See the Preface, “UNIX Commands,” to find references if you need help with the commands for this task or other system administration procedures. Note – Failure to halt the operating system properly can cause the loss of disk drive data. Note – Do not disconnect the terminal while the system is running.
3 3.3 Enterprise 4000 System 3.3.1 Powering On the System Note – It is advisable to connect an ASCII terminal to the system during installation. See Section 2.6, “Connecting an ASCII Terminal,” for terminal settings and connections. Observe the yellow (middle) LED on the front panel. It should go off when boot completes. If it remains on, observe the terminal screen for boot messages produced by the firmware diagnostic program during power-on. To power on the Enterprise 4000 system: 1.
3 Legend: Standby = OFF; no DC power On = Normal power ON Diagnostics = Normal power ON with full diagnostics Locked = Normal power ON in secure mode On Standby Diagnostics Locked AC connector AC power switch Figure 3-6 Key Switch Positions and AC Power Switch • The fans in the power supplies begin turning. • The top front panel LED (green) turns on immediately denoting the power supply is delivering DC power. • The middle front panel LED (yellow) flashes while POST runs for approximately 60 seconds.
3 6. Watch the terminal screen for error messages from the firmware diagnostic program. POST (power-on-self test) tests subassemblies and some interface paths between subassemblies. At the conclusion of testing, firmware automatically attempts to reconfigure the system, omitting any parts of the system that have failed diagnostics. If there are no faults, or if firmware completes a successful reconfiguration in response to detected faults, the system boots.
3 3.3.2 Reading Boot Messages Use the boot software messages to verify that all options are installed and recognized by the system. After firmware completes the system self test, a message similar to the following will appear on your screen. The message lists hardware detected in the system. Note – This screen display is an example only. The actual message displayed on the screen will depend on the software running on your system. 8-slot Ultra Enterprise 5000/4000, Keyboard Present OpenBoot -.
3 DC power (green) Fault (yellow) System running (green) Figure 3-8 System Status LEDs (Standalone Server) Table 3-2 summarizes LED status indications. After boot, check the status of the system by inspecting system status LEDs on the front panel. See Table 3-2 and Figure 3-8. Table 3-2 Front Panel LED System Status LED Position Condition Top LED (green) On — The power supply is delivering DC power. Middle LED (yellow) Flashing — (first 60 seconds of AC power) Self tests are running.
3 3.3.4 Powering Off the System Before turning off the system power, you must halt the operating system. See the Preface, “UNIX Commands,” to find references if you need help with the commands for this task or other system administration procedures. Note – Failure to halt the operating system properly can cause the loss of disk drive data. Note – Do not disconnect the terminal while the system is running.
3 3.4 Failure of Network Communications Description of the Problem The system cannot communicate with a network if the system and the network hub are not set in the same way for the Ethernet link integrity test. This problem particularly applies to 10BASE-T network hubs, where the Ethernet link integrity test is optional. This is not a problem for 100BASE-T networks, where the test is enabled by default.
3 a. Type: ok show-devs b. In the show-devs listing, find the node names. Node names take the general form /sbus@3,0/SUNW,hme@3,8c00000. Solution 1 Use this method while the operating system is running: 1. Become superuser. 2. Type: # eeprom nvramrc=”probe-all install-console banner apply disable-link-pulse device-name “ (Repeat for any additional device names.) # eeprom “use-nvramrc?”=true 3. Reboot the system (when convenient) to make the changes effective.
3 3-18 Ultra Enterprise 6000/5000/4000 Systems Installation Guide—November 1996
Using the Software 4 This chapter contains information about software for your Enterprise 6000/5000/4000 systems. 4.1 Operating System Software Refer to the operating system documentation that came with your system. 4.2 Solstice SyMON Software Solstice™ SyMON™ features a graphical user interface (GUI) display that shows various graphs reflecting system status.
4 4-2 Ultra Enterprise 6000/5000/4000 Systems Installation Guide—November 1996
Index A AC switch, 2-6, 3-2, 3-10 adjust, levelling pads, 1-12 air conditioning needs, 1-7 ASCII terminal cabling and setup, 2-10 removal, 3-9, 3-15 automatic installation, JumpStart, 3-1 B bar, stabilizer, 1-13 boot messages, 3-7, 3-13 clearance, system, 1-10 connecting, power cord, 2-5 cord, power, 1-15 D disk drive tray, use stabilizer bar, 1-13 drive disk, caution improper shutdown, 3-9 moving with power on, 3-3 test, 3-6 tray, safety, 1-13 duplicate addresses, caution, 2-13 C cabling ASCII terminal
floorspace, 1-9 H halting the system, 3-9, 3-15 I network cabling, 2-6 to 2-7 site preparation, 1-7 transceiver, 1-9 notes, cautions, warnings, xiv installation, preparing for, 1-1 P J panel replace kick, 2-1 rear screen, 2-1 POST error messages, 3-2, 3-10 LED interpretation, 3-6 program, 2-10 reconfiguration of system, 3-6, 3-12 restart, 3-6 SBus card, 3-6 power cabling, 2-4 cord, location, 1-15 off the system, 3-9, 3-15 on the system, 3-2 to 3-7 power-on self-test See POST precaution, automatic ins
usage of, 3-12 restart, POST, 3-6 S W warnings, notes, cautions, xiv wrench, leveling, 1-14 SBus card POST, 3-6 test, 3-6 caution, 2-13 SCSI bus, caution, 2-13 cabling, 2-12 server, lifting, 1-14 shipping and storing, 1-4 site preparation air conditioning, 1-7 floorspace, 1-9 network, 1-7 software, using, 4-1 stabilizer bar, 1-13 status LEDs, 3-6, 3-14 switch AC, 2-6, 3-2, 3-10 key, 3-3 local/remote, 3-4 reset, 3-6 system clearance, 1-10 T test drives, 3-6 link test, 2-10 SBus cards, 3-6 tools list, 1-1
Index-4 Ultra Enterprise 6000/5000/4000 Systems Installation Guide—November 1996
Reader Comment Card Your comments and suggestions are important to us. Please let us know what you think about the Ultra Enterprise 6000/5000/4000 Systems Installation Guide, part number 802-3844-11. Yes ❑ No ❑ 1. Were the procedures well documented? Please explain: Yes ❑ No ❑ 2. Were the tasks easy to follow? Please explain: Yes ❑ No ❑ 3. Were the illustrations clear? Please explain: Yes ❑ No ❑ 4. Was the information complete and easy to find? Please explain: 5.
