Sun StorEdge™ Network FC Switch-8 and Switch-16 Installation and Configuration Guide Sun StorEdge SAN 3.0 Release Sun Microsystems, Inc. 901 San Antonio Road Palo Alto, CA 94303 U.S.A. 650-960-1300 Part No. 816-0830-12 October 2001, Revision A Send comments about this document to: docfeedback@sun.
Copyright 2001 Sun Microsystems, Inc., 901 San Antonio Road, Palo Alto, CA 94303-4900 U.S.A. All rights reserved. This product or document is distributed under licenses restricting its use, copying, distribution, and decompilation. No part of this product or document may be reproduced in any form by any means without prior written authorization of Sun and its licensors, if any. Third-party software, including font technology, is copyrighted and licensed from Sun suppliers.
Declaration of Conformity Compliance Model Number: Product Name: Compliance ID Sun StorEdge network FC switch-16 EMC European Union This equipment complies with the following requirements of the EMC Directive 89/336/EEC: EN55022:1998/CISPR22:1997 EN55024:1998 EN61000-4-2 EN61000-4-3 EN61000-4-4 EN61000-4-5 EN61000-4-6 EN61000-4-8 EN61000-4-11 EN61000-3-2:1995 w/Amendments 1, 2 EN61000-3-3:1995 Class A 4 kV (Direct), 8 kV (Air) 3 V/m 1.0 kV AC Power Lines, 0.
iv Sun StorEdge Network FC Switch-8 and Switch-16 Installation and Configuration Guide • October 2001
Safety Agency Compliance Statements Depending on the type of power switch your device has, one of the following symbols may be used: Off - Removes AC power from the system. Read this section before beginning any procedure. The following text provides safety precautions to follow when installing a Sun Microsystems product. Safety Precautions Standby – The On/Standby switch is in the standby position.
SELV Compliance Safety status of I/O connections comply to SELV requirements. Power Cord Connection Caution – Sun products are designed to work with single-phase power systems having a grounded neutral conductor. To reduce the risk of electric shock, do not plug Sun products into any other type of power system. Contact your facilities manager or a qualified electrician if you are not sure what type of power is supplied to your building. Caution – Not all power cords have the same current ratings.
Laser Compliance Notice Symbole Sun products that use laser technology comply with Class 1 laser requirements. Die Symbole in diesem Handbuch haben folgende Bedeutung: Achtung – Gefahr von Verletzung und Class 1 Laser Product Luokan 1 Laserlaite Klasse 1 Laser Apparat Laser KLasse 1 Geräteschaden. Befolgen Sie die Anweisungen. Achtung – Hohe Temperatur. Nicht berühren, da Verletzungsgefahr durch heiße Oberfläche besteht.
Aufstellung von Sun-Geräten Die folgende Warnung gilt nur für Geräte mit Wartezustand-Netzschalter: Achtung – Um den zuverlässigen Betrieb Ihres Sun-Geräts zu gewährleisten und es vor Überhitzung zu schützen, dürfen die Öffnungen im Gerät nicht blockiert oder verdeckt werden. Sun-Produkte sollten niemals in der Nähe von Heizkörpern oder Heizluftklappen aufgestellt werden. Achtung – Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 Teil 1000 beträgt 70Db(A) oder weniger.
Gehäuseabdeckung Sie müssen die obere Abdeckung Ihres Sun-Systems entfernen, um interne Komponenten wie Karten, Speicherchips oder Massenspeicher hinzuzufügen. Bringen Sie die obere Gehäuseabdeckung wieder an, bevor Sie Ihr System einschalten. ■ Ne jamais introduire d’objets quels qu’ils soient dans une des ouvertures de l’appareil. Vous pourriez vous trouver en présence de hautes tensions dangereuses.
Modification du matériel Ne pas apporter de modification mécanique ou électrique au matériel. Sun Microsystems n’est pas responsable de la conformité réglementaire d’un produit Sun qui a été modifié. Positionnement d’un produit Sun Attention: – pour assurer le bon fonctionnement de votre produit Sun et pour l’empêcher de surchauffer, il convient de ne pas obstruer ni recouvrir les ouvertures prévues dans l’appareil.
Bloc-batterie CD-ROM Attention: – Les unités Sun StorEdge network FC switch-16 contiennent une batterie étanche au plomb (produits énergétiques portatifs n˚TLC02V50). Il existe un risque d’explosion si ce bloc-batterie est manipulé de façon erronée ou mal mis en place. Ne remplacez ce bloc que par un blocbatterie Sun Microsystems du même type. Ne le démontez pas et n’essayez pas de le recharger hors du système.
Precaución – Voltaje peligroso presente. Para reducir el riesgo de descarga y daños para la salud siga las instrucciones. Cumplimiento de la normativa SELV El estado de la seguridad de las conexiones de entrada/ salida cumple los requisitos de la normativa SELV. Conexión del cable de alimentación eléctrica Encendido – Aplica la alimentación de CA al sistema.
La siguiente advertencia se aplica solamente a equipos con un interruptor de encendido que tenga una posición "En espera": Precaución – El interruptor de encendido de este producto funciona exclusivamente como un dispositivo de puesta en espera. El enchufe de la fuente de alimentación está diseñado para ser el elemento primario de desconexión del equipo. El equipo debe instalarse cerca del enchufe de forma que este último pueda ser fácil y rápidamente accesible.
GOST-R Certification Mark Nordic Lithium Battery Cautions Norge ADVARSEL – Litiumbatteri — Eksplosjonsfare.Ved utskifting benyttes kun batteri som anbefalt av apparatfabrikanten. Brukt batteri returneres apparatleverandøren. Sverige VARNING – Explosionsfara vid felaktigt batteribyte. Använd samma batterityp eller en ekvivalent typ som rekommenderas av apparattillverkaren. Kassera använt batteri enligt fabrikantens instruktion. Danmark ADVARSEL! – Litiumbatteri — Eksplosionsfare ved fejlagtig håndtering.
Regulatory Compliance Statements Your Sun product is marked to indicate its compliance class: • • • • Federal Communications Commission (FCC) — USA Industry Canada Equipment Standard for Digital Equipment (ICES-003) — Canada Voluntary Control Council for Interference (VCCI) — Japan Bureau of Standards Metrology and Inspection (BSMI) — Taiwan Please read the appropriate section that corresponds to the marking on your Sun product before attempting to install the product.
ICES-003 Class A Notice - Avis NMB-003, Classe A This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada. ICES-003 Class B Notice - Avis NMB-003, Classe B This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
BSMI Class A Notice The following statement is applicable to products shipped to Taiwan and marked as Class A on the product compliance label.
xviii Sun StorEdge Network FC Switch-8 and Switch-16 Installation and Configuration Guide • October 2001
Contents 1. Introduction 1 New Features, Benefits, and Products New Device Names 2 2 On-Demand Node Creation 3 Fabric Connection of Hosts 3 Cascading of Switches 3 Higher Realized Bandwidth Support of Multiple Protocols 3 4 Support for More, Heterogeneous Storage Devices Support for New Hardware and Software Software Upgrade Only 4 4 Building Blocks for More Complex Topologies 2.
Supported Host Bus Adapters FC Tape 8 8 Software/Drivers 8 Array Storage Rules 8 L180 and L700 FC Tape Libraries FCIP (NFS/NAS and SNDR) Switches Zones 10 10 FC Tape Libraries Ports 10 11 12 12 Guidelines for Configuration Switches 15 15 Zones and Arrays 15 Zones and Storage 15 Configuration Examples 16 Single Host Connected to One Storage Array 16 Single Host Connected to Multiple Storage Arrays Multihost 26 Setting the Loop ID 3.
Attaching the Mounting Rails to the Expansion Cabinet Installing the Mounting Rails for 8-Port Switches Installing the Switch Connecting the Cables 47 50 Sun StorEdge A5200 and T3 Arrays Switch Activation 51 57 Configuring the Switch Ethernet Port 57 Using RARP to Change the IP Address 57 Installing the Sun StorEdge Network FC Switch 3.0 GUI Upgrading the GUI 6.
SL Zones and Name Server Zones 88 Creating On-Demand Device Nodes on Hosts for Fabric Configurations 89 Creating Device Nodes Without the Sun StorEdge Traffic Manager Software Enabled 89 Creating Device Nodes With the Sun StorEdge Traffic Manager Software Enabled 99 9.
Managing Fabric Devices Through Dynamic Reconfiguration Managing IP Networks Over Fibre Channel Networks Managing IP Networks in a SAN Installation Usage 10.
Zoning Error Messages 153 C. Frequently Asked Questions D.
Figures FIGURE 2-1 Single Host Connected to One Sun StorEdge A3500FC Controller Module FIGURE 2-2 Single Host Connected to One Sun StorEdge A5200 Array 17 FIGURE 2-3 Single Host Connected to One Sun StorEdge T3 Partner Pair 18 FIGURE 2-4 Single Host Connected to Multiple Sun StorEdge A3500FC Arrays, All SL Ports 20 FIGURE 2-5 Single Host Connected to Multiple Sun StorEdge A5200 Arrays, All SL Ports 21 FIGURE 2-6 Single Host Connected to Multiple Sun StorEdge A5200 Arrays and a Single FC-Tape Lib
FIGURE 4-1 Attaching the Mounting Rails 43 FIGURE 4-2 Detail of Rail Slots 44 FIGURE 4-3 Attaching the Mounting Rails for a 16-port Switch 45 FIGURE 4-4 Installing Four 8-Port Switches Into the Mounting Rails 47 FIGURE 4-5 Installing the Vent Panel— Two 8-Port Switch Configuration 48 FIGURE 4-6 Installing the Vent Panel—Four 8-Port Switch Configuration 49 FIGURE 4-7 Installing the Vent Panel for a 16-Port Switch FIGURE 4-8 Power Sequencer 51 FIGURE 4-9 The 8-Port Switch Power Connector 53
Preface The Sun StorEdge Network FC Switch-8 and Switch-16 Installation and Configuration Guide describes how to set up the Sun StorEdge™ Network FC Switch-8 and Switch -16 hardware and configure it to the network. It provides information and pointers to additional documentation you may need for configuring, troubleshooting, and using the switch. The book is intended for technical users who have experience with storage systems.
Typographic Conventions TABLE P-1 Typeface Meaning Examples AaBbCc123 The names of commands, files, and directories; on-screen computer output Edit your .login file. Use ls -a to list all files. % You have mail. AaBbCc123 What you type, when contrasted with on-screen computer output % su Password: AaBbCc123 Book titles, new words or terms, words to be emphasized Read Chapter 6 in the User’s Guide. These are called class options. You must be superuser to do this.
Related Documentation Product Application Title Part Number SANbox Installer/User’s information SANbox-16STD Fibre Channel Switch Installer’s/User’s Manual 875-3141-10 Installer/User’s information SANbox-8 Fibre Channel Switch Installer’s/User’s Manual 875-3142-10 Installer/User’s Information SANbox 8/16 Switch Management User’s Manual 875-3060-10 Installer/User’s Information SANbox 8/16 Switch Management User’s Manual 875-3143-10 Latest Information Sun StorEdge Network FC Switch-8 and Swi
Product Application Title Part Number Storage Cabinet Rackmount information Online Rackmount Placement Matrix 805-4748-xx Software RAID software RAID Manager 6.22 User's Guide 806-0478-10 manpage cfgadm utility cfgadm_fp 1. Check for the latest updates at http://sunsolve.sun.com. Accessing Sun Documentation Online A broad selection of Sun system documentation is located at: http://www.sun.
CHAPTER 1 Introduction This guide provides instructions for installing and configuring Sun StorEdge Network FC Switch-8 and Switch-16, Sun StorEdge SAN 3.0 release, hardware and software components. Hardware components include Fibre Channel switches, Fibre Channel host adapters, and storage devices and enclosures.
Fabrics and name services, configuring and changing zones on switches, converting to long device names used by Fabrics and Sun StorEdge Traffic Manager, and using on-demand device creation. New Features, Benefits, and Products This version of the Sun StorEdge SAN Product provides new features and benefits.
/devices/pci@f,4000/pci@4/SUNW,qlc@4/fp@0,0/ssd@w50020f200000225,0. Old symbolic device name: /dev/dsk/c4t3d0s2 New symbolic designation: /dev/dsk/c4t50020f200000225d0s2. On-Demand Node Creation The number of storage devices that can be attached to a host can grow to the thousands with the advent of SANs with native Fabric connectivity. Probing all these devices at boot time and creating device nodes can increase the boot time greatly.
Support of Multiple Protocols The StorEdge Network product supports both SCSI (FCP) and IP(FCIP) over the Fibre Channel. This allows both storage and networking applications to work on the SAN and minimizes the need for multiple networks. FCIP can be used in any supported topology and can be used for traditional IP applications and IP file access at the same time. Simultaneous SCSI and IP traffic in the same switch zone is not currently supported.
CHAPTER 2 Configurations This chapter contains information and instructions for configuring your Sun StorEdge Network FC Switch-8 or Switch-16 with one or more hosts and storage.
In a cascaded configuration, two switches are connected together via InterSwitchLinks (ISL). A hard zone and a nameserver zone span both switches. All hosts connected to these zones must be on one switch, and all storage must be on the other. Cascaded switches are supported only for long distance, and long wave GBICS are required between switches. Note – Only long wave Gigabit Interface Converters (LW GBIC) and cables are supported for connecting the cascading switches.
Supported Configurations To support a high-availability environment, use these configurations to ensure switch redundancy. See the example diagrams in this chapter for more information on the supported configurations.
Arrays ■ Sun StorEdge A5200 array ■ Sun StorEdge T3 array ■ Sun StorEdge T3+ array ■ Sun StorEdge A3500FC array Supported Host Bus Adapters ■ PCI Single Fibre Channel Network Adapter ■ PCI Dual Fibre Channel Network Adapter+ ■ CPCI Dual Fibre Channel Network Adapter FC Tape ■ Sun StorEdge L180 Tape Library with STK 9840 tape drives ■ Sun StorEdge L700 FC Tape Library with STK 9840 tape drives Software/Drivers For the most recent patches, go to http://sunsolve.Sun.COM/.
Sun StorEdge A5000 and A5100 arrays are not supported.
The Sun StorEdge T3 array and the Sun StorEdge T3+ array can be part of the same SL zone or nameserver zone. TABLE 2-4 Sun StorEdge A3500FC array 1 Feature Supported Cascading No Zone Type SL zone only Maximum number of arrays per SL zone 4 Maximum initiators per SL zone 2 1. The Sun StorEdge A3500 FC array is not supported on hosts that have Sun StorEdge Traffic Manager enabled or that have Fabric-connected host ports.
■ Sun StorEdge Network FC Switch-8 ■ Sun StorEdge Network FC Switch-16 Note – Make sure the switch chassis ID is not 0. You can change the chassis ID in the Switch Faceplate Display window. After changing the chassis ID, click the Apply button. For more information on the chassis ID, refer to the SANbox-8/16 Switch Management User’s Manual for Sun StorEdge Network FC switch 3.0. FC Tape Libraries You can configure either the Sun StorEdge L180 or L700 Tape Library with a switch.
Ports TABLE 2-6 Switch Port Types Port Type Supported SL-Ports Private loop (Sun StorEdge A5200 array, Sun StorEdge A3500FC array, Sun StorEdge T3 array, L180 or L700 FC-Tape device) TL-Ports Translated loop (Sun StorEdge T3 array) F-Ports Point-to-Point Fabric (HBA) T-Ports Trunk ports for switch cascading (ISLs) configured initially in Fabric port mode Zones Zoning allows the user to divide the switch ports into zones for more efficient and secure communication among functionally grouped nodes
nameserver zones are possible within one hard zone. Overlapping nameserver zones are not supported. In a hard zone containing F_Ports and TL_Ports, nameserver zones must be created if you need more than one zone. SL Zones SL zones on the switch allow the division of the Fabric into zones that define the ports that can communicate with each other. A particular port may be placed in only one SL zone (no overlapping SL zones).
■ Maximum cascading distance is ten kilometers ■ In cascaded configurations, hosts cannot be connected to both switches in a single zone with storage connected, and storage cannot be connected to both switches in a single zone. In other words, a switch zone can have remote storage only or local storage only, but cannot mix the two. ■ Switch-to-switch connection is supported for distance only ■ Only LW GBICS are supported between switches ■ Cascading is supported for nameserver zones only.
Guidelines for Configuration Switches For high-availability applications, configure two sets of switches in parallel. Zones and Arrays See TABLE 2-7 for more information on Zones and TABLE 2-8 for more information on zones, arrays and initiators. ■ Sun StorEdge T3 arrays support SL zones and nameserver zones (or zones in which a host has made a point-to-point Fabric connection to a switch and the Sun StorEdge T3 array is attached to a TL-port). ■ Do not mix different arrays in the same zone.
TABLE 2-8 Arrays, Zones, and Initiators Array Maximum Arrays/Zone Maximum Initiators/Zone Sun StorEdge A3500FCarray 4 2 Sun StorEdge A5200 array 3 2 initiators per loop, or a maximum of four per array Sun StorEdge T3 array 8 Sun StorEdge T3WG or 4 Sun StorEdge T3ES 2 for a single array, 4 for a partner pair Configuration Examples Single Host Connected to One Storage Array FIGURE 2-1 shows one host connected through fiber-optic cables to one Sun StorEdge A3500FC controller module.
Sun StorEdge A3500FC Arrays Host Switches Controller A Host adapter SL Host adapter SL FC-AL ports Controller B SCSI x 5 FC-AL ports Fiber-optic cables Drive tray x 5 Single Host Connected to One Sun StorEdge A3500FC Controller Module FIGURE 2-1 Switches Host Sun StorEdge A5200 array SL SL IBA IBB SL SL Fiber-optic cables FIGURE 2-2 Single Host Connected to One Sun StorEdge A5200 Array Chapter 2 Configurations 17
Switches Host Sun StorEdge T3 partner pair F TL F TL Host Adapter Host Adapter Fiber-optic cables FIGURE 2-3 Single Host Connected to One Sun StorEdge T3 Partner Pair Single Host Connected to Multiple Storage Arrays FIGURE 2-4 shows one host connected through fiber-optic cables to Sun StorEdge A3500FC controller modules. You can connect controller modules in the same or separate cabinets. FIGURE 2-5 shows one host connected to multiple Sun StorEdge A5200 arrays.
Caution – Make sure that the controller module of the array is split between two switches. For example, connect controller A to switch 1 and controller B to switch 2.
Sun StorEdge A3500FC Array Controller A FC-AL port Controller B FC-AL port SCSI x 5 Drive tray x 5 Sun StorEdge A3500FC Array Host Switches Host Adapter SCSI x 5 Host Adapter Drive tray x 5 Sun StorEdge A3500FC Array SCSI x 5 Drive tray x 5 FIGURE 2-4 20 Single Host Connected to Multiple Sun StorEdge A3500FC Arrays, All SL Ports Sun StorEdge Network FC Switch-8 and Switch-16 Installation and Configuration Guide • October 2001
Sun StorEdge A5200 arrays IBA Switches IBB SL Host SL SL SL Host Adapter IBA IBB Host Adapter SL SL SL SL IBA IBB FIGURE 2-5 Single Host Connected to Multiple Sun StorEdge A5200 Arrays, All SL Ports Chapter 2 Configurations 21
Sun StorEdge A5200 arrays IBA Switch 0 Host Host Adapter 1 2 3 4 5 6 7 8 IBB IBA IBB Host Adapter 1 2 3 4 5 6 7 8 IBA Switch 1 Switch 0 SL Zone 1 = Ports 1,2,3,4,6 Ports = All SL SL Zone 2 = Ports 5,7,8 Ports = All SL IBB FC Tape library Switch 1 SL Zone 1’ = Ports 1,2,3,4,6 Ports = All SL SL Zone 2’ = Ports 5,7,8 Ports = All SL FIGURE 2-6 22 Single Host Connected to Multiple Sun StorEdge A5200 Arrays and a Single FC-Tape Library Sun StorEdge Network FC Switch-8 and Switch-16 Inst
Sun StorEdge T3 partner pairs Host Host Adapter Switches F TL TL TL TL F TL TL TL TL Host Adapter FIGURE 2-7 Single Host Connected to Multiple Sun StorEdge T3 Partner Pairs Chapter 2 Configurations 23
Sun StorEdge T3 partner pairs Switch 0 Host Host Adapter 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Sun StorEdge A3500 FC array Controller A FC-AL Port Controller A FC-AL Port Host Adapter 1 2 3 4 5 6 7 8 9 11 10 12 13 14 15 16 SCSI x5 Controller A FC-AL Port Controller A FC-AL Port SCSI x5 Switch 1 Hard zone 1 = Ports 1-8 Hard zone 2= Ports 9-16 Switch 0 Nameserver Zone 1 = Ports 1,2,4 Ports: 1 = F Ports: 2 = TL Ports: 4 = TL Segmented loop zone 1 = Ports 14,15,16 Ports =
Zone 1 1 3 Zone 1 Host 2 5 4 6 7 8 9 10 1 2 11 12 3 4 13 14 5 6 15 16 7 8 Switch 2 Host Adapter IBA Switch 0 Host Adapter IBB Host Adapter Zone 1’ IBA Host Adapter Switches 0,2 and Switches 1,3 Nameserver Zone 1,1’ Switch 0,1 Ports: 1 = F Ports: 2 = T Switch 2,3 Ports: 1= T Ports: 2 = TL Ports: 4 = TL 1 2 3 4 5 7 6 1 2 8 3 5 4 6 7 8 9 11 10 12 13 14 15 16 Switch 1 Switch 0 and Switch 1 Segmented Loop Zone 1, Segmented Loop Zone 1’ Ports = 3,4,6 All Ports
Multihost FIGURE 2-10 shows an example of a multihost configuration: two hosts connected through fiber-optic cables, using switches, to two Sun StorEdge A3500FC controller modules. FIGURE 2-10 shows two hosts connect to a maximum of four Sun StorEdge A3500 FC arrays. FIGURE 2-11 shows two hosts connected to three Sun StorEdge A5200 arrays. FIGURE 2-12 shows two hosts connected to four Sun StorEdge T3 partner pairs.
Sun StorEdge A3500 FC Arrays Controller A FC-AL Port Controller B FC-AL Port SCSI x 5 Host Switches Drive Tray x 5 Host Adapter A Controller A Host Adapter FC-AL Port Controller B FC-AL Port SCSI x 5 Host Adapter B Host Adapter Drive Tray x 5 Controller A FC-AL Port Controller B FC-AL Port SCSI x 5 Drive Tray x 5 FIGURE 2-10 Two Hosts Connected to a Maximum of Four Sun StorEdge A3500FC Arrays All Ports SL Chapter 2 Configurations 27
Note – You can attach different storage types to the same switch so long as the storage devices are on different zones. Each controller that is connected to a switch must have a unique loop ID. Whenever you add a second controller to a switch, make sure that the loop ID of the controller being connected is different from the loop ID of any other controller currently connected to the same switch. Refer to “Setting the Loop ID” on page 32 for instructions on setting the loop ID of a controller.
Sun StorEdge T3 partner pairs Host Switches F Host Adapter Host Adapter F TL TL TL TL Host Host Adapter F Host Adapter F FIGURE 2-12 TL TL TL TL Two Hosts Connected to Four Sun StorEdge T3 Partner Pairs Chapter 2 Configurations 29
Note – You must enable Sun StorEdge Traffic Manager software or use Veritas VxDMP 3.2 for failover across multiple hosts to work. Set the mp_support on the Sun StorEdge T3 to mpxio.
Sun Enterprise E220 Host A 1 2 Host Adapter 3 4 Host Adapter 5 6 7 8 9 10 11 12 13 14 15 16 Host Adapter Host Adapter 1 2 3 4 5 6 7 8 Sun StorEdge A5200 Array Tape library Switch 0 Sun Enterprise E3000 Host A 1 2 3 4 5 6 7 8 9 11 10 13 14 15 16 Host Adapter Host Adapter Host Adapter Host Adapter Nameserver zone and SL zone cannot be in the same zone.
Note – You must enable Sun StorEdge Traffic Manager software or use Veritas VxDMP 3.2 for failover across multiple hosts to function. The mp_support on the Sun StorEdge T3 should be set to mpxio. Setting the Loop ID Setting the loop ID of the Sun StorEdge A3500 FC array is different from the procedure for the Sun StorEdge A5200 array and for the Sun StorEdge T3 array.
▼ To Verify the Loop ID of the Sun StorEdge A5200 and T3 Arrays ● Make sure that each array on a single loop has a unique target ID. If two Sun StorEdge T3 arrays have the same target ID on the same FC-AL loop, the software does not recognize their presence. Refer to the Sun StorEdge T3 documentation for information on verifying the loop ID. Refer to the Sun StorEdge A5200 documentation on verifying the loop ID for the Sun StorEdge A5200 array.
Controller B Controller B 8 4 2 1 ID Dec AL PA 0 15 16 1 2 Controller A ID Dec AL PA EF 0 EF 1 E8 1 E8 2 E4 2 E4 3 E2 3 E2 4 E1 4 E1 5 E0 5 E0 6 DC 6 DC 7 DA 7 DA 8 D9 8 D9 9 D6 9 D6 10 D5 10 D5 11 D4 11 D4 12 D3 12 D3 13 D2 13 D2 14 D1 14 D1 15 CE 15 CE FIGURE 2-15 34 Controller A 8 4 2 1 8 4 2 1 8 4 2 1 Sun StorEdge A3500 FC-AL ID Settings Sun StorEdge Network FC Switch-8 and Switch-16 Installation and Configuration Guide • Octo
CHAPTER 3 Installation Overview This chapter contains an overview of the tasks required for installing new Sun StorEdge Network FC Switch-8 and Switch-16 hardware and software. It also provides an overview of the tasks required to update the software for previously installed Sun StorEdge Network FC Switch-8 and Switch-16 SAN switches. To install the software for a Sun StorEdge Network FC Switch-8 and Switch-16 Version 3.0 switch, refer to the instructions in Chapter 6 in this guide.
Software Components and Patches For the most recent updates to TABLE 3-1, refer to the Sun StorEdge Network FC Switch8 and Switch-16 Release Notes.
TABLE 3-1 Minimum Software Component Versions and Patches (Continued) Non-Bundled Software Minimum Version Sun StorEdge T3 18Gb disk Firmware Minimum Patch 109115-09 VERITAS Volume Manager™ 3.2 VERITAS File System 3.4 Instant Image™ 3.0 fast Write Cache™ 3.0 SNDR 3.0 AP 2.3.1 StorTools™ 4.1 Sun StorEdge Network Storage Agent™ 2.1 VERITAS NetBackup™ 3.4 Solstice Backup™ 6.0 Sun Enterprise 3x00/4x00/5x00/6x00 Flash prom 3.2.
3. Install the GBICs. See the Sun Switch Management Installer's/User's Manual for the 8-port switch, or the SANbox Segmented Loop Switch User's Manual for instructions. 4. Install the vent panel. See "Installing the Vent Panel" on page 47. 5. Connect the cables and power cords. See Chapter 2 for configuration information. See also "Connecting the Cables" on page 50. 6. Configure the switch for the network. See Chapter 5 for information on configuring the switch to the network. 7. Install the SANSurfer 3.
PatchPro Expert PatchPro Expert analyzes the system configuration and currently installed patches with the latest patch revisions available on the http://sunsolve.Sun.Com. If new patch revisions are available on http://sunsolve.Sun.Com, it generates a list and allows you to download the patches. It also generates a list to indicate the order in which patches should be installed.
d. Under switches and HBAs, select the HBAs in your SAN. You do not need to select the switches under this block because the switch GUI/ firmware was captured when you selected the Network FC Switch, Version 3.0. 7. When your selections are complete, select Generate Patch List. An ordered list of the patches required for your selections displays. You can choose which patches to download, or you can download them all in one tar file.
CHAPTER 4 Hardware Installation This chapter describes how to mount the switch in an expansion cabinet, install the vent panel, and connect the switch to your disk arrays.
Attaching the Mounting Rails to the Expansion Cabinet The 8-port switch comes with a set of mounting rails that holds two switches. The 16-port switch comes with individual rails for each switch. This section describes how to attach the mounting rails to an expansion cabinet for two-switch and four-switch configurations.
Back L R Stopper screws FIGURE 4-1 Attaching the Mounting Rails 3. Working from the front of the cabinet, install the mounting rails by sliding the keyhole slot in the rail onto the screw. The rails for left and right are identical, but reversed, for the two sides. The large hole is oriented near the back for both rails. Use the slot marked L for the left rail. Use the slot marked R for the right rail.
L R FIGURE 4-2 Detail of Rail Slots 4. Install three 10-32 screws on each rail. 5. Tighten the fourth screw. ▼ To Attach Mounting Rails for Four 8- Port Switches 1. Mount the first two switches. See “To Attach Mounting Rails for Two 8-port Switches” on page 42. 2. Before you install the rails into the cabinet, loosely start two stopper screws into each rail (see FIGURE 4-2). 3. Working from the back of the cabinet, loosely start two screws for the mounting rails into the cabinet (see FIGURE 4-2).
▼ To Attach Mounting Rails for Two 16-Port Switches Each 16-port switch comes with two identical mounting rails. There is no difference between the left rail and the right rail. 1. Before you install the rails into the cabinet, loosely start two stopper screws into each rail (see FIGURE 4-3). 2. Working from the rear of the cabinet, loosely start two screws into the cabinet for each mounting rail, one at each end (see FIGURE 4-3).
4. Insert the remaining screws through the mounting rail into the cabinet rail. Do not tighten any of the screws until you have them all loosely started. 5. Tighten all the screws when all four screws in each bracket are in place. The order of tightening does not matter. Installing the Switch ▼ To Install the 8-port or 16-port Switch into the Cabinet 1. From the front of the cabinet, slide the first switch into the lowest of the mounting rails.
FIGURE 4-4 Installing Four 8-Port Switches Into the Mounting Rails Installing the Vent Panel This section describes how to install the vent panel on the switches in your configuration. “To Install the Vent Panel on Two 8-Port Switches” on page 47 “To Install the Vent Panels on Four 8-Port Switches” on page 48 “To Install the Vent Panel on a 16-Port Switch” on page 49 ▼ To Install the Vent Panel on Two 8-Port Switches 1. Mount the 1-U filler panel at the very top. Tighten the captive screws.
2. Mount the 1-U filler panel above the vent panel and below the existing 2-U filler panel. 3. Tighten the captive screws. 1-U filler panel 3- U Vent panel FIGURE 4-5 ▼ Installing the Vent Panel— Two 8-Port Switch Configuration To Install the Vent Panels on Four 8-Port Switches 1. Mount each of the two vent panels over the front of a set of two switches. No filler panel is necessary. 2. Tighten the captive screws.
FIGURE 4-6 ▼ Installing the Vent Panel—Four 8-Port Switch Configuration To Install the Vent Panel on a 16-Port Switch Each 16-port switch comes with its own vent panel. 1. Mount a vent panel over the front of each switch. No filler panel is necessary. 2. Tighten the captive screws.
FIGURE 4-7 Installing the Vent Panel for a 16-Port Switch Connecting the Cables Some storage cabinets may have shorter and fewer power cords. In these cases, you must use the Y cable, provided with your switch, to increase the number of power connections and provide adequate power cord length. Install the Y cables only in the J8 or J12 connections of the power sequencer.
Sun StorEdge A5200 and T3 Arrays ▼ To Connect the Cables to a Sun StorEdge T3 Array 1. Power off the system. For instructions about powering off the Sun StorEdge T3 Array, refer to the documentation that came with the array. 2. Unplug the power cord from both fan trays and from the J12 connections on both sequencers. See FIGURE 4-8 for the J12 location. J8 J12 FIGURE 4-8 Power Sequencer 3.
▼ To Connect the Cables to a Sun StorEdge A5200 Array If the existing power cords are too short, replace them with the Y cable. 1. Power off the system. For instructions about powering off the Sun StorEdge A5200 Array, refer to the documentation that came with the array. 2. Remove the lower vented side panel from the right side. 3. Working from the back, push the lowest Sun StorEdge A5200 array about eight inches toward the front of the cabinet. This provides access to the cables. 4.
1. Working from the back, connect the power cord(s). FIGURE 4-9 shows the 8-port switch power connector. FIGURE 4-10 shows the 16-port switch power connector. FIGURE 4-11 shows the power connections for two or four switches. Allow the power cord to dangle temporarily.
Switch 1 Power cords Switch 2 Switch 3 Switch 4 FIGURE 4-11 Power Connection for Two or Four Switches 2. Install the GBIC. See the “Removal and Replacement Procedures” chapter of the SANbox 8/16 Segmented Loop Switch User’s Manual for instructions on installing a GBIC. 3. Use a tie wrap to secure the Fibre Channel cables, as shown in FIGURE 4-12 and FIGURE 4-13.
Power Fibre channel cables Tie wrap FIGURE 4-12 Extension power cord Cable Routing for the 8-Port Switch Fibre FibreChannel Channelcables cables Fibre channel cables m icr FIGURE 4-13 os ys te m s Cable Routing for the 16-Port Switch Note – Connections to storage arrays are not shown in these figures.
▼ To Connect the Cables to a Sun StorEdge L180 or L700 FC Tape Library 1. Refer to the installation documentation that came with your tape library for instructions on cabling. 2. Comply with the rules for configuring an FC Tape Library with a Sun StorEdge FC Network Switch. See “FC Tape Libraries” on page 11.
CHAPTER 5 Switch Activation This chapter contains the procedures for bringing the new Sun StorEdge FC Switch 3.0 software onto the network. For more details about the switch, refer to Switch Management User’s Manual. “Configuring the Switch Ethernet Port” on page 57 “Installing the Sun StorEdge Network FC Switch 3.0 GUI” on page 61 “Setting the Stage Type” on page 66 Configuring the Switch Ethernet Port The IP address of the switch is set to the default value of 10.0.0.1.
You will need the following information to change the IP address: IP address _______________________ Contact the person who maintains your network for this information. MAC address _____________________ See FIGURE 5-1 and FIGURE 5-2 for the location of the MAC Address. Switch name ______________________ This is the assigned name of the switch you are installing.
4. Back up the affected management station configuration files: # cp -p /etc/nsswitch.conf /etc/nsswitch.conf.SAV # cp -p /etc/hosts /etc/hosts.SAV 5. On a host connected to the same subnet as the switch, edit the /etc/ethers file by adding the MAC address and switch name. For example: 8:0:20:7d:93:7e switch-name In this example: ■ 8:0:20:7d:93:7e is the MAC address ■ switch-name is the name of the switch you are installing. 6. Edit the /etc/hosts file with the IP address and switch name.
9. If RARP is not running, start the RARP daemon in the Solaris software environment by typing: # /usr/sbin/in.rarpd -ad The IP address will now automatically download to the switch after you install the switch and power on the system. Note – RARP might not work properly if you have connected the ethernet port of the FC switch to an Ethernet switch; this is due to the long time it might take for the Ethernet switch to transmit the RARP.
Installing the Sun StorEdge Network FC Switch 3.0 GUI The Sun StorEdge FC Switch 3.0 GUI application is supported on the JDK™ 1.3.02 . Refer to the CD documentation, 804-7880-10, packaged with the system, for installing the JDK. ▼ To View the SANsurfer Application Version 1. Open the Help menu in the SANsurfer Graphical User Interface (GUI). 2. Select About SANsurfer. The SANsurfer application version number displays in the window. Upgrading the GUI If the Sun StorEdge FC Switch 2.0 (Version 2.07.
▼ To Remove the 2.0 GUI 1. In the root directory, type: # pkgrm SUNWsmgr The following message displays: The following package is currently installed. SUNWsmgr SANsurfer, Qlogic Fibre Channel Administration (i86pc, sparc) 2.07 Do you want to remove this package? 2. Type: # y [Yes] The following message is displayed. ## Removing installed package instance ## Verifying package dependencies. ## Processing package information.
▼ To Install the 3.0 GUI Patch If you have the 2.0 or 2.1 GUI already installed and you have the patch for the 3.0 GUI, you can upgrade the GUI with the 3.0 patch. 1. If you want to preserve your current user administration and Fabric configurations, copy the current user administration file (app.dat) and Fabric information file (default.fab) to another file. 2.
b. Enter the switch IP address in the Fabric window of the GUI. It may take a few seconds for the switch icon to become gray. You can click the Refresh button. c. After the switch icon becomes gray, click the Sun logo. Note – If the icon remains red, it is likely that the IP address is wrong, or that the switch cannot be accessed from that subnet, or the switch lacks power or an ethernet connection. ▼ To Verify and Load the Switch Firmware You must have the correct firmware revision for the 3.
5. Double-click the switch icon. The Topology View screen is erased, and the Switch FacePlate Display screen displays. 6. Make a note of the firmware revision level. The revision level appears on the second line of the text in the upper right corner of the Switch FacePlate Display screen. ▼ To Load the Firmware Revision 1. Locate the file containing the new firmware on the management station. The default location is /usr/opt/SUNWsmgr/flash. 2. Choose Special>Update Flash.
Setting the Stage Type After installing the GUI, you can leave the stage type to SL zoning (segmented loop) or change it to FLS-IO Transfer (IOT) mode. SL zones enable you to divide the SL ports into multiple zones that define which ports will communicate with each other. Communications occur only between ports in the defined SL zone. The default state type is SL zoning. IOT mode allows F-port, T-port, and TL-port configuration. Only switches in IOT mode can be cascaded together.
CHAPTER 6 Installing a New SAN This chapter contains the following topics that describe how to install a new SAN system: ■ ■ ■ ■ “Required Software Components” on page 67 “Downloading Patches and Packages” on page 69 “Verifying Successful Patch Downloads” on page 69 “Installing the Software” on page 70 Required Software Components The following software components might be required for your particular SAN system. Refer to the documentation for each individual product to insure proper installation.
■ Solstice DiskSuite Solstice DiskSuite is an unbundled software product that is delivered with Solaris software. Solstice DiskSuite provides host-based storage management, such as mirroring and striping of disks, which provides greater reliability and volume size. Solstice DiskSuite 4.2.1 also implements RAID 5. ■ VERITAS Volume Manager VERITAS Volume Manager is a separately installed software product that provides host-based storage management, such a disk labeling, mirroring, striping, and RAID 5.
Downloading Patches and Packages You can download the required software components from the following web sites listed in TABLE 6-1. TABLE 6-1 Software Download Sites Software Downloading Web Site packages and documentation http://www.sun.com/storage/san/ patches http://sunsolve.sun.com Note – You can also get all the patches and packages for your configuration from the SunSolve web site. If you use PatchPro to generate a patch list, a README.txt file with the installation order is included.
Note – The direcotry /usr/ucb has another version of the sum utility. Use /usr/ 5bin/sum. CODE EXAMPLE 6-2 Example of GNU md5sum Utility % md5sum 108982-09.zip 1297fcd385f618c726489c6c7f57c900 108982-09.zip Download the GNU md5sum utility from http://www.sunfreeware.com or from http://sunsolve.sun.com/md5/md5.tar.z. 2. Compare the checksum value that is displayed to the patch checksum value given at the Checksum File link http://sunsolve.Sun.
TABLE 6-2 Software Installation Sequence (Continued) Patch or Package Software 108984-081 /kernel/drv/qlc driver patch 109529-06 luxadm, liba5k and libg_fc patch 111412-05 Sun StorEdge Traffic Manager patch 111413-04 luxadm/liba5k and libg_fc patch 111095-05 fcp/fp/fctl/usoc drivers patch 111096-03 fcip driver patch 111097-04 qlc driver patch 111267-021 /kernel/fs/specfs patch 111846-01 cfgadm plug-in library patch SUNWvtsst Sun StorTools package SUNWrasag Network Storage Agent pack
4. Install cfgadm plug-in library packages SUNWcfpl and SUNWcfplx. # pkgadd -d pkg-location SUNWcfpl # pkgadd -d pkg-location SUNWcfplx 5. Install the SAN Foundation Kit SUNWsan patch 111847-xx. If you installed the Sun SAN release 3.0, do not install this patch. a. To find out if this patch has been installed, type: # showrev -p | grep 111847 If the patch has been installed the system returns: Patch: 111847-01 Obsoletes: Requires: Incompaticles: Packages: SUNWsan b.
8. Install luxadm/libg_fc/liba5k patch 109529-xx. Patch 109529-06 may have been included with your operationg system. Use the showrev command to see it it has been included. # patchadd patch-location/109529-06 9. Install Network Storage Traffic Manager patch 111412-xx. # patchadd patch-location/111412-04 10. Install luxadm/libg_fc/liba5k patch 111413-xx. 11. Install fcp/fp/fctl/usoc drivers patch 111095-xx. # patchadd patch-location/111095-05 12. Install fcip driver patch 111096-03.
16. Update MANPATH to access cfgadm_fp(1M) man page. For sh or ksh, type: # MANPATH=/opt/SUNWsan/man:$MANPATH;export MANPATH For csh, type: % setenv MANPATH /opt/SUNWsan/man:$MANPATH 17. Install StorTools package SUNWvtsst. If you plan to used your system as a SAN Management host, install Step 17, Step 18, and Step 19. # pkgadd -d pkg-location SUNWvtsst 18. Install Network Storage Agent package SUNWrasag. # pkgadd -d pkg-location SUNWrasag 19.
■ ■ ■ ■ name server zones additional initiators per zone host fabric connectivity cascaded switch configurations Chapter 6 Installing a New SAN 75
76 Sun StorEdge Network FC Switch-8 and Switch-16 Installation and Configuration Guide • October 2001
CHAPTER 7 Upgrading the SAN This chapter contains the following topics regarding how to upgrade your SAN system to the latest version: ■ ■ ■ “Downloading Patches and Packages” on page 77 “Verifying Upgrade Compliance” on page 77 “To Upgrade Software” on page 78 Downloading Patches and Packages See TABLE 6-1 on page 69 for all the locations of patches and packages for download. Download all patches and packages to the host prior to beginning the upgrade procedure.
▼ To Upgrade Software If you have multiple hosts on your SAN, you can upgrade them simultaneously or one at a time without affecting your SAN environment. Hosts that are not being upgraded will not be affected during the upgrade. You can upgrade the host software one host at a time or several hosts in parallel. Caution – Your system will be unavailable to users and the SAN during the upgrade procedure. The order in which the SAN components should be upgraded is as follows: 1.
pkg_name is the name of the package you need to obtain the information on. # pkginfo -l pkg_name 1. Upgrade your SUNWsan package to StorEdge SAN 3.0. Before you start, check your system to see if it has been installed, and if it is already up to date. Use the pkginfo command to see if it has been installed. # pkginfo SUNWsan The system returns: system SUNWsan SAN Foundation Kit The output indicates that the SUNWsan package has already been installed.
cfgadm Plug-in Library Packages 1. Install cfgadm plug-in library packages SUNWcfpl and SUNWcfplx. # pkgadd -d pkg-location SUNWcfpl # pkgadd -d pkg-location SUNWcfplx pkgadd -d pkg-location SUNWcfplx Software Installation 1. Follow Step 6 through Step 16 on page 72 and page 74 of Chapter 6. SAN Management Software If this system is being used as a SAN Management host, follow the steps in this section. If the system is not being used as a SAN Management host, go to “Switch Firmware” on page 83.
1. Upgrade StorTools package SUNWvtsst. Check your SAN Management host to find the version of the StorToolsTM installed. # pkginfo -l SUNWvtsst The system returns: PKGINST: SUNWvtsst NAME: StorTools Diagnostic Package CATEGORY: Diagnostics ARCH: sparc VERSION: 4.1 BASEDIR: /opt VENDOR: Sun Microsystems Computer Corporation DESC: StorTools Diagnostic Package PSTAMP: Built by buildst@diag240.Central.Sun.
Network Storage Agent 1. Upgrade the Network Storage Agent package, SUNWrasag. Check the version of the NetworkStorage Agent on your SAN Management host. # pkginfo -l SUNWrasag The system returns: PKGINST: SUNWrasag NAME: Network Storage Agent CATEGORY: system ARCH: sparc VERSION: 2.
Sun StorEdge Network FC Switch Manager 1. Upgrade Sun StorEdge Network FC Switch Manager package, SUNWsmgr. SANsurfer Switch Manager SAN release 3.0 can manage both 2.0 and 3.0 versions of the Sun StorEdge FC Network switch. Earlier versions of SANsurfer Switch Manager are not supported and may cause improper switch operation when used for managing SAN 3.0, Sun StorEdgeTM Network FC Switch.
a. Stop Network Storage Agent Monitoring on all hosts connected to this switch. This insures that unnecessary events and notifications are not generated, when the switch is reset after the firmware upgrade. b. Use the newly installed SANsurfer Switch Manager to upgrade the switch firmware. Refer to the switch documentation for this upgrade procedure. Upload the appropriate switch firmware to the switch and reset it upon completion. c.
CHAPTER 8 Configuring the SAN This chapter contains the following topics regarding how to configure your SAN system. For more detailed information on managing multiple switches and managing switch zones, see the SANbox 8/16 Switch Management User’s Manual.
▼ To Save a Switch IP Configuration to Disk 1. In the Fabric window, type the switch IP address in the IP Address field. 2. Click File and select Save As. a. Type the Fabric name of the switch. b. Click OK. The Fabric is saved to disk. ▼ To Save a Subsequent Switch IP Configuration to Disk 1. Click the gray Sun icon to highlight the Fabric fields. 2. Click Delete. The current Fabric field line disappears. 3. Select the IP Address field and type the new switch IP address. 4.
▼ To Delete a Switch Configuration 1. Click File. 2. Click Delete Fabrics File. 3. Select the Fabric you want to delete. 4. Click OK. The Fabric is deleted. Managing Cascaded Switches A cascaded configuration is managed through the Ethernet connection to one of the switches. For redundancy, connect the Ethernet of both switches. Switch management is done through the Ethernet and Inter Switch Links (ISL) which provides connection to the second switch.
Managing Switch Zones With the exception of the following clarifications regarding compatibility with the Sun StorEdge FC Network switch-8 and switch-16 rules, refer to pages 2-60 to 2-70 of the SANbox-8/16 Switch Management User’s Manual for instructions about managing switch zones.
Creating On-Demand Device Nodes on Hosts for Fabric Configurations In SL zones, hosts and storage devices connect in private loop topology, and devices are available by default when devices are added to an SL zone. With the Sun StorEdge Traffic Manager software enabled, the Solaris host configures the devices as Sun StorEdge Traffic Manager devices.
■ ■ “To Configure All Fabric Devices on a Fabric-Connected Host Port” on page 95 “To Unconfigure All Fabric Devices on a Fabric-Connected Host Port” on page 97 ▼ To Discover Fabric Devices Visible on a Host Fibre channel host ports c0 and c1, and the devices attached to them, provide an example of discovering Fabric devices. This procedure also shows the device configuration information that can be displayed with the cfgadm(1M) command.
Note – The cfgadm -l commands displays information about fibre channel host ports. Use the cfgadm -al command to also display information about fibre channel devices. The lines that include a port World Wide Name in the attachment point ID field associated with c0 represent a Fabric device. Use the cfgadm configure and unconfigure commands to manage those devices be made available on Solaris host.
4. Verify that the selected Fabric device is configured.
CODE EXAMPLE 8-1 (Continued) Maximum prefetch: 0x0 Device Type: Disk device Path(s): /dev/rdsk/c0t50020F2300006077d1s2 /devices/pci@1f,2000/pci@1/SUNW,qlc@4/fp@0,0/ ssd@w50020f2300006077,1:c,raw DEVICE PROPERTIES for disk: 50020f2300006077 Status(Port B): O.K. Vendor: SUN Product ID: T300 WWN(Node): 50020f2000006077 WWN(Port B): 50020f2300006077 Revision: 0117 Serial Num: Unsupported Unformatted capacity: 558448.
▼ To Unconfigure a Fabric Device This procedure describes how to unconfigure a Fabric device that is attached to the Fabric-connected host port c0. 1. Become superuser. 2. Identify the device to be unconfigured. Only the devices on a Fabric-connected host port can be unconfigured.
4. Verify that the selected Fabric device is unconfigured.
Note – Stop all device activity to each Fabric device on the selected port and unmount any filesystems on each Fabric device. If the device is under any volume manager’s control, see the documentation for your volume manager for maintaining the Fabric device. # cfgadm -c configure c0 Note – This operation repeats the configuration operation of an individual device for all the devices on c0, and may be time consuming if the number of devices on c0 is large. 4. Verify that all devices on c0 are configured.
▼ To Unconfigure All Fabric Devices on a Fabric-Connected Host Port This procedure describes how to unconfigure all configured Fabric devices that are attached to a Fabric-connected host port. 1. Become superuser. 2. Identify the Fabric devices to be unconfigured. Only the devices on a Fabric-connected host port can be unconfigured.
4. Verify that all the devices on c0 are unconfigured.
Creating Device Nodes With the Sun StorEdge Traffic Manager Software Enabled This section describes how to perform Fabric device configuration steps on a host that has the Sun StorEdge Traffic Manager software enabled. For details on enabling Sun StorEdge Traffic Manager software, refer to “Managing Sun StorEdge Traffic Manager with a Volume Manager” on page 117. The devices that are attached to Fabric-connected HBA port are not configured by default.
2. Display information about the attachment points on the system. # cfgadm -l Ap_Id c0 c1 c2 Type Receptacle fc-fabric connected fc-private connected fc-fabric connected Occupant Condition unconfigured unknown configured unknown unconfigured unknown An attachment point id (Ap_Id) on a Fabric-connected host port is a path to a Sun StorEdge Traffic Manager device. In this example, c0 and c2 represent Fabricconnected host ports and c1 represents a private, loop-connected host port.
In the previous example, host ports c0 and c2 are connected to the two ports of a Sun StorEdge T3 enterprise array, which has two port WWNs associated with it: attachment point IDs 50020f2300006077 and 50020f2300006107. ▼ To Configure a Fabric-Connected Device as a Sun StorEdge Traffic Manager Device This example uses Fabric-connected host ports c0 and c2 to configure Fabric devices as Sun StorEdge Traffic Manager devices on a host that has the Sun StorEdge Traffic Manager software enabled.
3. Configure Fabric devices and create Sun StorEdge Traffic Manager devices. # cfgadm -c configure c0::50020f2300006077 c2::50020f2300006107 4. Verify that the selected devices are configured.
CODE EXAMPLE 8-3 (Continued) Vendor: SUN Product ID: T300 WWN(Node): 50020f2000006077 WWN(Port A): 50020f2300006077 WWN(Port B): 50020f2300006107 Revision: 0117 Serial Num: Unsupported Unformatted capacity: 558448.
CODE EXAMPLE 8-3 (Continued) /devices/scsi_vhci/ssd@g60020f20000061073ac8b4c50004ed3a:c,raw Controller /devices/pci@1f,2000/pci@1/SUNW,qlc@4/fp@0,0 Device Address 50020f2300006107,0 Class primary State ONLINE Controller /devices/pci@1f,2000/pci@1/SUNW,qlc@5/fp@0,0 Device Address 50020f2300006077,0 Class secondary State STANDBY Note – The luxadm (1M) output on 50020f2300006107 will show the same information as the previous display.
Only the devices on a Fabric-connected host port can be unconfigured through the cfgadm unconfigure command.
CODE EXAMPLE 8-4 # cfgadm -al Ap_Id Type Receptacle Occupant Condition c0 fc-fabric connected configured unknown c0::50020f2300006077 disk connected unconfigured unknown c0::50020f23000063a9 disk connected configured unknown c1 fc-private connected configured unknown c1::220203708b69c32b disk connected configured unknown c1::220203708ba7d832 disk connected configured unknown c1::220203708b8d45f2 disk connected configured unknown c1::220203708b9b20b2 disk connected configured unknown c2 fc-fabric connected
An attachment point id (Ap_Id) on a Fabric-connected host port is a path to a Sun StorEdge Traffic Manager device. Only the devices on a Fabric-connected host port can be unconfigured through the cfgadm unconfigure command.
4. Verify that the selected device is unconfigured.
CODE EXAMPLE 8-6 (Continued) Maximum prefetch: 0x0 Device Type: Disk device Path(s): /dev/rdsk/c6t60020F20000061073AC8B52D000B74A3d0s2 /devices/scsi_vhci/ssd@g60020f20000061073ac8b52d000b74a3:c,raw Controller /devices/pci@1f,2000/pci@1/SUNW,qlc@5/fp@0,0 Device Address 50020f2300006077,1 Class primary State ONLINE DEVICE PROPERTIES for disk: 50020f2300006077 Status(Port B): O.K.
1. Become superuser. 2. Identify a Fabric-connected host port to be configured.
CODE EXAMPLE 8-7 (Continued) Device Address Class State 50020f2300006077,1 primary ONLINE DEVICE PROPERTIES for disk: 50020f2300006077 Status(Port B): O.K. Vendor: SUN Product ID: T300 WWN(Node): 50020f2000006077 WWN(Port B): 50020f2300006077 Revision: 0117 Serial Num: Unsupported Unformatted capacity: 558448.
4. Verify that all devices on c2 are configured.
CODE EXAMPLE 8-8 (Continued) Controller Device Address Class State Controller Device Address Class State /devices/pci@1f,2000/pci@1/SUNW,qlc@4/fp@0,0 50020f2300006107,1 secondary STANDBY /devices/pci@1f,2000/pci@1/SUNW,qlc@5/fp@0,0 50020f2300006077,1 primary ONLINE DEVICE PROPERTIES for disk: 50020f2300006077 Status(Port A): O.K. Status(Port B): O.K.
▼ To Unconfigure All Fabric-Connected Devices on Sun StorEdge Traffic Manager Enabled Ports Note – Whether Sun StorEdge Traffic Manager is enabled or not, the unconfigure operation for Fabric devices is identical, but the result of the operation is different. When Sun StorEdge Traffic Manager is enabled, Solaris removes Sun StorEdge Traffic Manager related path or device node information. An attachment point id (Ap_Id) on a Fabric-connected host port is a path to a Sun StorEdge Traffic Manager device.
Note – This operation repeats the unconfigure command of an individual device for all the all devices on c2, and it can be time consuming if the number of devices on c2 is large 4. Verify that all of the devices on c2 are unconfigured.
116 Sun StorEdge Network FC Switch-8 and Switch-16 Installation and Configuration Guide • October 2001
CHAPTER 9 Managing the SAN This chapter explains how to manage the SAN system. For information about managing device-node creation on SANs, see “Creating On-Demand Device Nodes on Hosts for Fabric Configurations” on page 89. The scope of this chapter is limited to the operations required from the perspective of the Solaris operating environment. It does not cover other aspects such as device availability and devicespecific management.
Managing Without a Volume Manager You can use the Sun StorEdge Traffic Manager software to manage multiple paths to a device. 1. Install the drivers. 2. Enable the Sun StorEdge Traffic Manager software system-wide by setting the mpxio-disable field in the /kernel/drv/scsi_vhci.conf file to “no”. Additional explanation of this file is provided in the Sun StorEdge Traffic Manager Installation and Configuration Guide. 3.
Managing Switch Zones For the following topics, see the SANBox-8/16 Switch Management User’s Manual: Sun StorEdge Network FC Switch 3.
▼ To Rezone a Sun StorEdge A5200 Array from Host A 1. Stop all disk activity to the StorEdge A5200 array. 2. Unmount any file systems currently using disks in Sun StorEdge A5200 array. 3. Deport any VM disk groups. 4. Run luxadm remove command to remove the Sun StorEdge A5200 array from host A. The system is now ready for rezoning. You can reassign the Sun StorEdge A5200 array from Host A to Host B. ▼ To Rezone a Sun StorEdge A5200 Array to Host B 1.
Rezoning and Reassigning Sun StorEdge A3500FC LUNs from Host A to Host B Rezoning to remove a storage device from host A and add it to host B causes host A to loose all access to the storage device. To rezone a Sun StorEdge A3500FC array from one host to another host, perform the following two procedures: ■ ■ ▼ “To Rezone a Sun StorEdge A3500FC Array From Host A” on page 121 “To Rezone a Sun StorEdge A3500FC Array to Host B” on page 121 To Rezone a Sun StorEdge A3500FC Array From Host A 1.
b. Run the following commands: # /etc/init.d/rdacctrl stop # /etc/init.d/rdacctrl config # /etc/init.d/rdacctrl start 2. Import any Volume Manager disk groups. 3. Mount any Volume Manager volumes in the /etc/vfstab file. You may need to run the fsck command. Rezoning and Reassigning Sun StorEdge T3 Arrays from Host A to Host B Rezoning to remove a storage device from host A and add it to host B causes host A to loose all access to the storage device.
▼ To Rezone a Sun StorEdge T3 Array to Host B 1. If necessary, configure all paths to the Sun StorEdge T3 array using the cfgadm c configure command. This will create device nodes. Perform this step if the Sun StorEdge T3 array is connected in a name server zone and is accessed by a host port connected to a switch F-port. For additional information, refer to “Creating On-Demand Device Nodes on Hosts for Fabric Configurations” on page 89 of Chapter 8 2. Import any Volume Manager disk groups. 3.
Adding a Sun StorEdge T3 Workgroup or Enterprise Array The following applies to when the Sun StorEdge T3 array is connected as a Fabric device (an array to a switch TL_port and a host port to a switch F_port). If Sun StorEdge Traffic Manager is enabled, refer to “To Configure a Fabric-Connected Device as a Sun StorEdge Traffic Manager Device” on page 101. If Sun StorEdge Traffic Manager is not enabled, refer to “To Configure a Fabric Device” on page 91.
■ “Removing a FC-Tape Drive” on page 126 Removing a Sun StorEdge A5200 Array Use the luxadm remove_device command to hot remove a disk drive, enclosure, or chain of enclosures. This command interactively guides you through the hot removal of one or more devices.
6. Click remove. For additional information, see the Sun StorEdge RAID Manager 6.22 User’s Guide.
If the same Fabric devices are intact during DR operations and need to be reconfigured on the host, reconfigure them through an on-demand node creation after you add the system component and it is available to the host. ■ ■ If Sun StorEdge Traffic Manager is enabled, refer to “To Configure a FabricConnected Device as a Sun StorEdge Traffic Manager Device” on page 101. If Sun StorEdge Traffic Manager is not enabled, refer to “To Configure a Fabric Device” on page 91.
Managing IP Networks in a SAN This section contains the following topics: ■ ■ ■ ■ “Installation” on page 128 “Configuration” on page 131 “Invocation” on page 131 “Usage” on page 132 Installation The FCIP depends on the instance of fp. If multiple HBAs are present, plumb manually after identifying the fp instance on which IP should be plumbed. The following two procedures determine fp instances.
3. Manually plumb fp instances. Use the ifconfig interface plumb command. # ifconfig fcip0 plumb If no error message is displayed, manual plumbing has succeeded. Repeat this step for the other fp instances identified in Step 2. ▼ To Determine an FP Instance for a Known HBA Port Physical Device Path 1. Determine the HBA PCI adapter slot and the I/O board PCI slot. You will need this information to perform the calculation in Step 2.
CODE EXAMPLE 9-1 PCI Single Fibre Channel Network Adapter Device Path “/pci@b,2000/SUNW,qlc@2/fp@0,0” 7 “fp” TABLE 9-1 PCI Single Fibre Channel Network Adapter /etc/path_to_inst Device Path Entry Entry Item Entry Value Physical Name “pci@b,2000/SUNW,qlc@2/fp@0.0” Instance Number 7 Driver Binding Name “fp” 3. Manually plumb the fp instance. Use the ifconfig interface plumb command In this example, interface would be fcip7..
Configuration Each network interface should have an /etc/hostname.interface file defining the name of the IP address associated with it. For example, an FCIP network interface fcip0 will have a file named /etc/hostname.fcip0. 1. Manually create a /etc/hostname.interface file with a text editor so it contains a single line that identifies the host name or interface IP address. 2. Use a text editor to make any additional entries to the /etc/inet/hosts file.
▼ To Start a Network Interface Manually 1. Use the ifconfig command with the appropriate interface. For example, to enable an FCIP interface associated with fp instance 0 and an IP address of 192.9.201.10, you would use the following command: # ifconfig fcip0 plumb 192.9.201.10 netmask 255.255.255.0 The ifconfig command is described in more detail in the ifconfig (1M)manpage. Ask your network administrator for an appropriate IP address and netmask information. 2.
CHAPTER 10 Troubleshooting Tools and Resources This chapter contains information and procedures for correcting faults in initial configuration and subsequent faults. Additional information and resources are available at http://www.sun.com/service/support/sunsolve/index.html. The website contains information on software versions and provides necessary patches for customers.
■ SANsurfer Webgui.log (found in $HOME/.Webgui) Component Based Resources: ■ Raid Manager 6.
Network Storage Agent can help in patch and firmware maintenance and to display a topology view of the entire SAN. You can use Stortools to capture a snapshot of the system configuration, as well as to assist in component and system-wide testing and verification. See TABLE 6-1 for download URLs for StorTools and Network Storage Agent packages and documentation. Common Problems General Tips For Troubleshooting In all cases: ■ Verify that all patches and firmware are the most recent ones available.
Corrective Measures ■ Using the SANsurfer GUI, verify that the zoning is correct. ■ Using the SANsurfer GUI, check that the port configuration is correct.
Corrective Measures ■ Check that the /kernel/drv/scsi_vhci.conf configuration is correct. ■ Make sure mpxio-disable=no is set. ■ Check /var/adm/messages for errors. ■ For Sun StorEdge T3 Array installations, make sure the sys mp_support setting is set to mpxio. If the problem persists, contact your Sun Service representative. Problem Failing a path (to secondary or to primary) does not succeed using Sun StorEdge Traffic Manager.
CODE EXAMPLE 10-1 Output for Sun StorEdge T3 Array # luxadm display /dev/rdsk/ c6t60020F20000003C53B4AE50C0005A95Dd0s2 DEVICE PROPERTIES for disk: /dev/rdsk/ c6t60020F20000003C53B4AE50C0005A95Dd0s2 Status(Port A): O.K. Status(Port B): O.K. Vendor: SUN Product ID: T300 WWN(Node): 50020f20000003d5 WWN(Port A): 50020f23000003d5 WWN(Port B): 50020f23000003c5 Revision: 0117 Serial Num: Unsupported Unformatted capacity: 68294.
CODE EXAMPLE 10-2 Output for Sun StorEdge A5200 Array: # luxadm display /dev/rdsk/c6t200000203719F802d0s2 DEVICE PROPERTIES for disk: /dev/rdsk/c6t200000203719F802d0s2 Status(Port A): O.K. Status(Port B): O.K. Vendor: SEAGATE Product ID: ST39103FCSUN9.0G WWN(Node): 200000203719f802 WWN(Port A): 210000203719f802 WWN(Port B): 220000203719f802 Revision: 034A Serial Num: LS4705570000 Unformatted capacity: 8637.
path and that the path is not available for a failover operation. Both paths of a dual connected Sun StorEdge A5200 array are ONLINE. Only one path of a Sun StorEdge T3 array is ONLINE; the other path is STANDBY. ■ Check that the cfgadm listing to verify Ap_Ids, representing Fabric-connected Sun StorEdge T3 Array paths, are configured and in the normal condition. ■ Check /var/adm/messages or Network Storage Agent for any related errors ■ Check the SANsurfer GUI for error counters.
■ If necessary, set Force Prom Mode to force the switch to IP address 10.0.0.1. Connect to the switch in this mode and reset the desired IP address. Set back to normal mode and reset the switch. Try reconnecting. (See the switch hardware manuals listed in “Related Documentation” on page xxix, for more details). If the problem persists, contact your Sun Service representative.
142 Sun StorEdge Network FC Switch-8 and Switch-16 Installation and Configuration Guide • October 2001
APPENDIX A Software Architecture This appendix contains a block diagram of the software architecture for the Sun StorEdge Network FC Switch-8 and Switch-16, version 3.0 software update. See FIGURE A-1 on the next page.
SUN SERVERS (Solaris 8 4/01) User Level SAN/Storage Mgmt Software (Component Manager, cfgadm, luxadm) Standard Applications (format, cfgadm, mount, mkfs,…) Diag/Monitoring Software (StorTools, NWSAgent) (libg_fc, liba5k, switchAPI,…) Kernel Level Layered Storage Drivers (RDAC, SDS,…) SCSI Target Drivers (ssd, st…) TCP/IP Streams Stack & Modules DLPI Solaris SCSA Framework TCP/IP Kernel Modules/ and Drivers for Out of Band Interfaces (Out of Band) StorEdge Traffic Manager FCP FCIP FP/FCTL (Fibre
APPENDIX B Error Messages cfgadm Error Messages TABLE B-1 cfgadm Utility Messages Error Message Corrective Action cfgfadm: Insufficient condition An Ap_Id provided for the configure operation is not in a normal condition. Refer to cfgadm_fp(1M) for related information on host port and Fabric device conditions. cfgadm: Configuration operation not supported An Ap_Id provided for the configure operation does not have a Fabric related topology.
Error Message Corrective Action cfgadm: Library error: Failed to get Fabric device list The operation to get Fibre Channel device list on a host port failed. Check the condition field of the host port from the cfgadm listing and diagnose the Fiber connection of the host port. cfgadm: Library error: failed to create device node: errno text The configure operation failed on the device node with error specified in errno text.
Faceplate Display Error Messages TABLE B-3 Faceplate Display Messages Error Message Corrective Action Fabric ID must be < 16 and chassis ID must be < 64. Both must be >= 0. Correct these values and APPLY again. Correct values and apply again. (NOTE: The Fabric ID is fixed; only the chassis ID needs to be verified.) Chassis ID cannot conflict with an existing chassis in the Fabric. Correct these values and APPLY again.
Fabric has more than one Switch: Configuration operation cannot be applied. Default configuration cannot be restored on a switch in a cascaded Fabric: remove all inter-switch links or set links offline, then retry. Switch has reported communications errors. Your changes will most likely not take effect. Try anyway? Verify network connection1 to Fabric and retry. You cannot transition an existing T-Port to an SL or TL Port.
Help Error Messages TABLE B-4 Help Messages Error Message Corrective Action Could not find help.txt file in archive. Java Archive may be corrupt. The SUNWsmgr package was not installed correctly, or has become corrupted: re-install the SUNWsmgr package. Application Error Messages TABLE B-5 Application Messages Error Message Corrective Action User Login Failed. Enter correct login ID and password and retry.
Network Configuration Error Messages TABLE B-6 Network Configuration Messages Error Message Corrective Action Invalid gateway address entered. Changes not applied. Enter a valid gateway address and apply again. Port Display Error Messages TABLE B-7 Port Display Messages Error Message Corrective Action Reset Failed! Verify network connection1 to Fabric and retry. Invalid testing argument entered. Test cancelled. An incorrect value was entered. Retry the test with correct values.
Topology Display Error Messages TABLE B-8 Topology Display Messages Error Message Corrective Action Source IP switch cannot be deleted. SANsurfer does not allow the user to delete the switch with the network connection; only the cascaded switch may be deleted. The GUI has detected a loss in Ethernet connectivity to the sourceIP switch in the Fabric. Check your Ethernet connections. Click OK to return to FABRIC list window. Verify network connection1 to Fabric.
1. Verify network connection to Fabric: Check that the correct IP address for the Fabric is entered in the Fabric Display. If the address is incorrect, then enter the correct IP address for the network switch in the Fabric. Verify that the gateway address is correctly configured on the workstation. If the gateway is incorrect, then configure the correct gateway. Verify that the Fabric is accessible through the network. For example, ping the switch and verify that responses are not being dropped.
User Administration Error Messages TABLE B-9 User Administration Messages Error Message Corrective Action Can't delete LAST SUPER USER. Do not try to delete the last superuser Duplicate user names are not allowed. Enter a unique user name and retry. Invalid value entered! Verify that all values entered are valid and retry. Invalid value entered! Enter a date newer than 01/01/1970. Enter a date later than 01/01/1970 and retry.
Attempt to clear zones on switch […] failed. REFRESH and try again. Verify network connection1 to Fabric and Fibre Channel links to switch, then retry. Zoning file operation failed! Verify network connection1 to Fabric and Fibre Channel links to switch, then retry. The file specified was either an invalid file or the file was not found. Verify that file exists and is a valid file, then retry. A switch has failed to respond during the zoning operation. Zoning operation failed.
APPENDIX C Frequently Asked Questions This chapter contains answers to questions encountered when configuring the SAN. After installing all required software I connected T3 to a switch TL port and a host to a switch F port. But the Sun StorEdge T3 array is not available from the Solaris host. The Fabric devices must be configured through on-demand node creation to be available on the Solaris host.
Follow the instructions displayed. ii. Type: # pkgadd -d Follow the instructions displayed. Note – If patches have been installed on top of the SUNWsmgr package, you must reinstall those patches. What do I do if the Fabric Icon is not present in the Fabric Window? The Fabric Icon is not present when the GUI is installed for the first time. Verify that the default.fab file is not empty and that the user is assigned to a nonempty Fabric file in the Admin window.
Note – The Default Switch is shipped with Switch IP address: 10.0.0.1 Mask: 255.0.0.0 Gateway: 0.0.0.0 Contact your system administrator regarding the correct Gateway and Mask address. In most standard networks, only the last byte of the IP address is used for the sub network. In that case, your Mask would be 255.255.255.0. What do I do if the Fabric icon is red in the Fabric window? If the icon remains red after the IP address is entered, verify that the following conditions exist: a.
How do I verify the Switch Ethernet Connection through SANsurfer? The window shows the active Ethernet connection on the Fabric Management Switch. If the application loses its ability to communicate with the Ethernet connection, it displays the Ethernet connection in Red. Select the Ethernet connection. The Ethernet Connection turns Blue when selected and the Ethernet information displays at the left side of the window. Double-click the Ethernet Connection to go to the Network Configuration window.
Note – If the restore file used on the current Fabric is not the information that was created from this Fabric, the IP information that is restored to this Fabric will be that of switches used to create the archive file in use in another Fabric. Using an archive file from another Fabric might result in duplicate IP information. Note that a replacement switch must be an exact replacement of the switch being removed.
Refer to Section 2-23, “Performing an Archive/Restore of a Fabric.” How do I identify Duplicate Chassis IDs in a Fabric? If a Chassis ID of a switch has the same value as another switch in the Fabric, only one of the two switches appears in the Topology window and the Logged-in LED on the connection port(s) between the switches blinks rapidly. What do I do if a Port is in an unknown mode: Press the Refresh button. Refer to Section 2-48, second NOTE.
What do I do if a Port is not appearing in the Zoning Window? Criteria for Displaying a Port The application polls each switch to determine the ports that have a device attached to them. If a port is configured and has a GBIC installed, it is shown as inactive unless the device responds to contact made with it. Port modes are determined at the time the zoning window is entered.
7. Click the Apply button to save the changes. The new Fabric contains four zones for this zone type. When the two Fabrics are connected, the result contains zone 1 from both Fabrics combined in zone 1, zone 2 contains the ports defined for the original Fabric A, zone 3 contains the original ports defined for zone 3 of Fabric B, and zone 4 contains the ports defined in the original zone 2 of Fabric B. After installing the HBA in F-Port mode on port-1, the devices on TL ports cannot be seen.
APPENDIX D Sample Installation Session CODE EXAMPLE D-1 contains output from an installation session using minimum patch levels available at the time of publication. CODE EXAMPLE D-1 # pkgadd -d /download SUNWsan Processing package instance from SAN Foundation Kit (sparc) 1.0 Copyright 2001 Sun Microsystems, Inc. All rights reserved. Using as the package base directory. ## Processing package information. ## Processing system information.
CODE EXAMPLE D-1 permission during the process of installing this package. Do you want to continue with the installation of [y,n,?] y Installing SAN Foundation Kit as ## Installing part 1 of 1. /opt/SUNWsan/bin/san_recover /opt/SUNWsan/man/sman1m/luxadm.1m /opt/SUNWsan/man/sman7d/scsi_vhci.
CODE EXAMPLE D-1 Patch packages installed: SUNWcsu SUNWcsxu SUNWfcp SUNWfcpx SUNWfctl SUNWfctlx SUNWhea SUNWusoc SUNWusocx # patchadd /download/108984-08 Checking installed patches... Verifying sufficient filesystem capacity (dry run method)... Installing patch packages... Patch number 108984-08 has been successfully installed. See /var/sadm/patch/108984-08/log for details Patch packages installed: SUNWcsr SUNWcsu SUNWcsxu SUNWhea SUNWqlc SUNWqlcx # patchadd /download/111412-04 Checking installed patches..
CODE EXAMPLE D-1 SUNWcsxu SUNWhea SUNWmdi SUNWmdix # patchadd /download/111095-05 Checking installed patches... Executing prepatch script... Verifying sufficient filesystem capacity (dry run method)... Installing patch packages... Patch number 111095-05 has been successfully installed. See /var/sadm/patch/111095-05/log for details Executing postpatch script...
CODE EXAMPLE D-1 SUNWcsxu SUNWfcip SUNWfcipx SUNWhea # patchadd /download/111097-04 Checking installed patches... Executing prepatch script... Verifying sufficient filesystem capacity (dry run method)... Installing patch packages... Patch number 111097-04 has been successfully installed. See /var/sadm/patch/111097-04/log for details Executing postpatch script... Patch packages installed: SUNWcsr SUNWcsu SUNWcsxu SUNWhea SUNWqlc SUNWqlcx # patchadd /download/109529-06 Checking installed patches...
CODE EXAMPLE D-1 Patch number 111413-03 has been successfully installed. See /var/sadm/patch/111413-03/log for details Executing postpatch script... Patch packages installed: SUNWluxop SUNWluxox # pkgadd -d /download SUNWcfpl Processing package instance from fp cfgadm plug-in library (sparc) 11.8.0,REV=2001.07.14.21.42 Copyright 2001 Sun Microsystems, Inc. All rights reserved. ## Processing package information. ## Processing system information.
CODE EXAMPLE D-1 ## ## ## ## ## ## Processing package information. Processing system information. Verifying package dependencies. Verifying disk space requirements. Checking for conflicts with packages already installed. Checking for setuid/setgid programs. Installing fp cfgadm plug-in library (64-bit) as ## Installing part 1 of 1. Installation of was successful. # patchadd /download/111846-01 Checking installed patches... Verifying sufficient filesystem capacity (dry run method).
CODE EXAMPLE D-1 Verifying sufficient filesystem capacity (dry run method)... Installing patch packages... Patch number 110614-02 has been successfully installed. See /var/sadm/patch/110614-02/log for details Patch packages installed: SUNWses SUNWsesx # pkgadd -d /download SUNWvtsst Processing package instance from StorTools Diagnostic Package Prototype (sparc) 4.1 Using as the package base directory. ## Processing package information. ## Processing system information.
CODE EXAMPLE D-1 /opt/SUNWvtsst/bin/.version /opt/SUNWvtsst/bin/a3500fctest /opt/SUNWvtsst/bin/a5ksestest /opt/SUNWvtsst/bin/a5ktest /opt/SUNWvtsst/bin/afb_checksum.data /opt/SUNWvtsst/bin/afb_texture.
CODE EXAMPLE D-1 /opt/SUNWvtsst/bin/modules/is_hba_qlc /opt/SUNWvtsst/bin/modules/is_hba_socal /opt/SUNWvtsst/bin/modules/is_hub_config /opt/SUNWvtsst/bin/modules/is_switched /opt/SUNWvtsst/bin/modules/is_tape_fc /opt/SUNWvtsst/bin/modules/isolate_a5k_by_scsi /opt/SUNWvtsst/bin/modules/lbf_loop_test /opt/SUNWvtsst/bin/modules/lw_insert_dev_eport_fiber /opt/SUNWvtsst/bin/modules/lw_insert_dev_eport_loopback /opt/SUNWvtsst/bin/modules/lw_insert_dev_fiber /opt/SUNWvtsst/bin/modules/lw_insert_dport_fiber /opt/
CODE EXAMPLE D-1 /opt/SUNWvtsst/bin/modules/lw_restore_dev_gbic /opt/SUNWvtsst/bin/modules/lw_restore_dev_mia /opt/SUNWvtsst/bin/modules/lw_restore_device /opt/SUNWvtsst/bin/modules/lw_restore_dport_fiber /opt/SUNWvtsst/bin/modules/lw_restore_dport_gbic /opt/SUNWvtsst/bin/modules/lw_restore_hba_eport_fiber /opt/SUNWvtsst/bin/modules/lw_restore_hba_eport_gbic /opt/SUNWvtsst/bin/modules/lw_restore_hba_fiber /opt/SUNWvtsst/bin/modules/lw_restore_hba_gbic /opt/SUNWvtsst/bin/modules/lw_restore_iport_fiber /opt/
CODE EXAMPLE D-1 /opt/SUNWvtsst/bin/pm/perf.arm.pm /opt/SUNWvtsst/bin/pm/perf.gray.pm /opt/SUNWvtsst/bin/pm/perf.pm /opt/SUNWvtsst/bin/pm/reset.arm.pm /opt/SUNWvtsst/bin/pm/reset.gray.pm /opt/SUNWvtsst/bin/pm/reset.pm /opt/SUNWvtsst/bin/pm/start.arm.pm /opt/SUNWvtsst/bin/pm/start.gray.pm /opt/SUNWvtsst/bin/pm/start.pm /opt/SUNWvtsst/bin/pm/stop.arm.pm /opt/SUNWvtsst/bin/pm/stop.gray.pm /opt/SUNWvtsst/bin/pm/stop.pm /opt/SUNWvtsst/bin/qlctest /opt/SUNWvtsst/bin/socaltest /opt/SUNWvtsst/bin/sparcv9/.
CODE EXAMPLE D-1 /opt/SUNWvtsst/bin/sparcv9/modules/hba_ready /opt/SUNWvtsst/bin/sparcv9/modules/ifp_core /opt/SUNWvtsst/bin/sparcv9/modules/iport_ready /opt/SUNWvtsst/bin/sparcv9/modules/is_a5k_device_installed /opt/SUNWvtsst/bin/sparcv9/modules/is_a5k_device_online /opt/SUNWvtsst/bin/sparcv9/modules/is_dev_daisy_chained /opt/SUNWvtsst/bin/sparcv9/modules/is_disk_a3500fc /opt/SUNWvtsst/bin/sparcv9/modules/is_disk_a5k /opt/SUNWvtsst/bin/sparcv9/modules/is_disk_fc /opt/SUNWvtsst/bin/sparcv9/modules/is_disk_
CODE EXAMPLE D-1 /opt/SUNWvtsst/bin/sparcv9/modules/lw_replace_dev_gbic /opt/SUNWvtsst/bin/sparcv9/modules/lw_replace_dev_mia /opt/SUNWvtsst/bin/sparcv9/modules/lw_replace_device /opt/SUNWvtsst/bin/sparcv9/modules/lw_replace_dport_fiber /opt/SUNWvtsst/bin/sparcv9/modules/lw_replace_dport_gbic /opt/SUNWvtsst/bin/sparcv9/modules/lw_replace_hba_eport_fiber /opt/SUNWvtsst/bin/sparcv9/modules/lw_replace_hba_eport_gbic /opt/SUNWvtsst/bin/sparcv9/modules/lw_replace_hba_gbic /opt/SUNWvtsst/bin/sparcv9/modules/lw_r
CODE EXAMPLE D-1 /opt/SUNWvtsst/bin/sparcv9/stexpert.td /opt/SUNWvtsst/bin/sparcv9/sunlink /opt/SUNWvtsst/bin/sparcv9/switchtest /opt/SUNWvtsst/bin/sparcv9/t3test /opt/SUNWvtsst/bin/sparcv9/take_snapshot /opt/SUNWvtsst/bin/sparcv9/vts_cmd /opt/SUNWvtsst/bin/sparcv9/vtsinfo.a /opt/SUNWvtsst/bin/sparcv9/vtsinfo.so /opt/SUNWvtsst/bin/sparcv9/vtsk /opt/SUNWvtsst/bin/stdiscover /opt/SUNWvtsst/bin/stexpert /opt/SUNWvtsst/bin/stexpert.rb /opt/SUNWvtsst/bin/stexpert.
CODE EXAMPLE D-1 /opt/SUNWvtsst/lib/locale/C/LC_MESSAGES/qlctest.msg /opt/SUNWvtsst/lib/locale/C/LC_MESSAGES/socaltest.msg /opt/SUNWvtsst/lib/locale/C/LC_MESSAGES/stexpert.cat /opt/SUNWvtsst/lib/locale/C/LC_MESSAGES/sunlink.msg /opt/SUNWvtsst/lib/locale/C/LC_MESSAGES/switchtest.msg /opt/SUNWvtsst/lib/locale/C/LC_MESSAGES/t3test.msg /opt/SUNWvtsst/lib/locale/C/LC_MESSAGES/vtsk.msg /opt/SUNWvtsst/lib/locale/C/LC_MESSAGES/vtstty.help /opt/SUNWvtsst/lib/locale/C/LC_MESSAGES/vtstty.
CODE EXAMPLE D-1 # pkgadd -d /download SUNWrasag Processing package instance from Network Storage Agent (sparc) 2.1r1 The selected base directory must exist before installation is attempted. Do you want this directory created now [y,n,?,q] y Using as the package base directory. ## Processing package information. ## Processing system information. ## Verifying disk space requirements. ## Checking for conflicts with packages already installed.
CODE EXAMPLE D-1 /opt/SUNWrasag/System/Storage_1.1.mof /opt/SUNWrasag/System/System1.0.tar.
CODE EXAMPLE D-1 /opt/SUNWrasag/bin/myread /opt/SUNWrasag/bin/pcicomp /opt/SUNWrasag/bin/pcidump /opt/SUNWrasag/bin/perf /opt/SUNWrasag/bin/prototype /opt/SUNWrasag/bin/ptopo /opt/SUNWrasag/bin/ras_install /opt/SUNWrasag/bin/rasagent /opt/SUNWrasag/bin/rasagent.sh /opt/SUNWrasag/bin/rashstart /opt/SUNWrasag/bin/rashttp /opt/SUNWrasag/bin/rasstat /opt/SUNWrasag/bin/rawdump /opt/SUNWrasag/bin/readToc /opt/SUNWrasag/bin/readmess /opt/SUNWrasag/bin/reset /opt/SUNWrasag/bin/rgrep /opt/SUNWrasag/bin/saf.
CODE EXAMPLE D-1 /opt/SUNWrasag/bin/writeNetConnect /opt/SUNWrasag/discman/bin/discman /opt/SUNWrasag/discman/bin/sparcv9/discman /opt/SUNWrasag/discman/bin/sparcv9/stdiscover /opt/SUNWrasag/discman/bin/stdiscover /opt/SUNWrasag/discman/discman.cat /opt/SUNWrasag/discman/lib/libfcald.so /opt/SUNWrasag/discman/lib/libsanbox.so /opt/SUNWrasag/discman/lib/sparcv9/libfcald.so /opt/SUNWrasag/discman/lib/sparcv9/libsanbox.so /opt/SUNWrasag/docs/InstallInstruct.pdf /opt/SUNWrasag/docs/ReleaseNotes.
CODE EXAMPLE D-1 /opt/SUNWrasag/htdocs/a5000.gif /opt/SUNWrasag/htdocs/arrow1.gif /opt/SUNWrasag/htdocs/arrow2.gif /opt/SUNWrasag/htdocs/bg.gif /opt/SUNWrasag/htdocs/buttons.js /opt/SUNWrasag/htdocs/device_registration.html /opt/SUNWrasag/htdocs/discover.html /opt/SUNWrasag/htdocs/doc.html /opt/SUNWrasag/htdocs/dot_blue.gif /opt/SUNWrasag/htdocs/dot_clear.gif /opt/SUNWrasag/htdocs/empty.html /opt/SUNWrasag/htdocs/empty2.html /opt/SUNWrasag/htdocs/fc_readwrite.html /opt/SUNWrasag/htdocs/fcutil.
CODE EXAMPLE D-1 /opt/SUNWrasag/htdocs/gif/space.gif /opt/SUNWrasag/htdocs/gifTopo/bclick.gif /opt/SUNWrasag/htdocs/gifTopo/bg0.gif /opt/SUNWrasag/htdocs/gifTopo/bout.gif /opt/SUNWrasag/htdocs/gifTopo/bover.gif /opt/SUNWrasag/htdocs/gifTopo/dot_blue.gif /opt/SUNWrasag/htdocs/gifTopo/dot_clear.gif /opt/SUNWrasag/htdocs/gifTopo/item.gif /opt/SUNWrasag/htdocs/gifTopo/item0.gif /opt/SUNWrasag/htdocs/gifTopo/item1.gif /opt/SUNWrasag/htdocs/gifTopo/line.gif /opt/SUNWrasag/htdocs/gifTopo/menu_root.
CODE EXAMPLE D-1 /opt/SUNWrasag/htdocs/san.html1 /opt/SUNWrasag/htdocs/san.html2 /opt/SUNWrasag/htdocs/sanF.html /opt/SUNWrasag/htdocs/sanWelcome.html /opt/SUNWrasag/htdocs/san_discover.html /opt/SUNWrasag/htdocs/san_health.html /opt/SUNWrasag/htdocs/san_health_pass.html /opt/SUNWrasag/htdocs/san_help.html /opt/SUNWrasag/htdocs/san_merge.html /opt/SUNWrasag/htdocs/san_utilities_login.html /opt/SUNWrasag/htdocs/san_verify.html /opt/SUNWrasag/htdocs/save /opt/SUNWrasag/htdocs/sched.
CODE EXAMPLE D-1 /opt/SUNWrasag/htdocs/topo_gifs/t300.gif /opt/SUNWrasag/htdocs/utilities.html /opt/SUNWrasag/htdocs/welcome.html /opt/SUNWrasag/install/install_end /opt/SUNWrasag/install/install_intro /opt/SUNWrasag/install/install_master /opt/SUNWrasag/install/install_slave /opt/SUNWrasag/install/postinstall /opt/SUNWrasag/install/preremove /opt/SUNWrasag/lib/Agent.pm /opt/SUNWrasag/lib/Agent/A3500FCAgent.pm /opt/SUNWrasag/lib/Agent/A5KAgent.pm /opt/SUNWrasag/lib/Agent/BROCADEAgent.
CODE EXAMPLE D-1 /opt/SUNWrasag/lib/Date/Format.pm /opt/SUNWrasag/lib/Date/Language.pm /opt/SUNWrasag/lib/Date/Parse.pm /opt/SUNWrasag/lib/Debug.pm /opt/SUNWrasag/lib/DeviceId.pm /opt/SUNWrasag/lib/Event.pm /opt/SUNWrasag/lib/Events.pm /opt/SUNWrasag/lib/FC.pm /opt/SUNWrasag/lib/FCConfig/Python.pm /opt/SUNWrasag/lib/FCRules.pm /opt/SUNWrasag/lib/FCRules/Rule1.pm /opt/SUNWrasag/lib/FCRules/Rule2.pm /opt/SUNWrasag/lib/FCRules/Rule3.pm /opt/SUNWrasag/lib/FCRules/Rule4.pm /opt/SUNWrasag/lib/FCRules/Rule6.
CODE EXAMPLE D-1 /opt/SUNWrasag/lib/GUI/A5KUtil.pm /opt/SUNWrasag/lib/GUI/Cache.pm /opt/SUNWrasag/lib/GUI/Config.pm /opt/SUNWrasag/lib/GUI/Devices.pm /opt/SUNWrasag/lib/GUI/Errlog.pm /opt/SUNWrasag/lib/GUI/EventLog.pm /opt/SUNWrasag/lib/GUI/Graph.pm /opt/SUNWrasag/lib/GUI/Hosts.pm /opt/SUNWrasag/lib/GUI/Instr.pm /opt/SUNWrasag/lib/GUI/InstrReport.pm.old /opt/SUNWrasag/lib/GUI/MessageLog.pm /opt/SUNWrasag/lib/GUI/Notifs.pm /opt/SUNWrasag/lib/GUI/Providers.pm /opt/SUNWrasag/lib/GUI/RUNAgent.
CODE EXAMPLE D-1 /opt/SUNWrasag/lib/HTTP/Daemon.pm /opt/SUNWrasag/lib/HTTP/Date.pm /opt/SUNWrasag/lib/HTTP/Headers.pm /opt/SUNWrasag/lib/HTTP/Headers/Auth.pm /opt/SUNWrasag/lib/HTTP/Headers/ETag.pm /opt/SUNWrasag/lib/HTTP/Headers/Util.pm /opt/SUNWrasag/lib/HTTP/Message.pm /opt/SUNWrasag/lib/HTTP/Negotiate.pm /opt/SUNWrasag/lib/HTTP/Request.pm /opt/SUNWrasag/lib/HTTP/Request/Common.pm /opt/SUNWrasag/lib/HTTP/Response.pm /opt/SUNWrasag/lib/HTTP/Status.pm /opt/SUNWrasag/lib/Health.
CODE EXAMPLE D-1 /opt/SUNWrasag/lib/LWP/Protocol/data.pm /opt/SUNWrasag/lib/LWP/Protocol/file.pm /opt/SUNWrasag/lib/LWP/Protocol/ftp.pm /opt/SUNWrasag/lib/LWP/Protocol/gopher.pm /opt/SUNWrasag/lib/LWP/Protocol/http.pm /opt/SUNWrasag/lib/LWP/Protocol/https.pm /opt/SUNWrasag/lib/LWP/Protocol/mailto.pm /opt/SUNWrasag/lib/LWP/Protocol/nntp.pm /opt/SUNWrasag/lib/LWP/RobotUA.pm /opt/SUNWrasag/lib/LWP/Simple.pm /opt/SUNWrasag/lib/LWP/UserAgent.pm /opt/SUNWrasag/lib/LWP/media.types /opt/SUNWrasag/lib/ListSort.
CODE EXAMPLE D-1 /opt/SUNWrasag/lib/NWS/Host.pm /opt/SUNWrasag/lib/NWS/SAN.pm /opt/SUNWrasag/lib/NWS/SCH_Events.pm /opt/SUNWrasag/lib/NWS/SCH_Storage.pm /opt/SUNWrasag/lib/NWS/Schema.pm /opt/SUNWrasag/lib/NWS/Schema1.pm /opt/SUNWrasag/lib/NWS/Switch.pm /opt/SUNWrasag/lib/NWS/T3.pm /opt/SUNWrasag/lib/NWS/key.xml /opt/SUNWrasag/lib/Net/Config.pm /opt/SUNWrasag/lib/Net/Domain.pm /opt/SUNWrasag/lib/Net/Ping.pm /opt/SUNWrasag/lib/Net/SNMP.pm /opt/SUNWrasag/lib/Net/Telnet.pm /opt/SUNWrasag/lib/Net/hostent.
CODE EXAMPLE D-1 /opt/SUNWrasag/lib/Provider/NetConnectProvider.pm /opt/SUNWrasag/lib/RASAgentSNMPTrap.pm /opt/SUNWrasag/lib/Report.pm /opt/SUNWrasag/lib/ReportContent.pm /opt/SUNWrasag/lib/Rules.pm /opt/SUNWrasag/lib/SNMP_Session.pm /opt/SUNWrasag/lib/Scheduler.pm /opt/SUNWrasag/lib/SelectSaver.pm /opt/SUNWrasag/lib/Serialize.pm /opt/SUNWrasag/lib/Shuttle.pm /opt/SUNWrasag/lib/Socket.pm /opt/SUNWrasag/lib/Socket.pm0 /opt/SUNWrasag/lib/Solaris/Procfs.pm /opt/SUNWrasag/lib/Solaris/Procfs/Filesystem.
CODE EXAMPLE D-1 /opt/SUNWrasag/lib/URI/_userpass.pm /opt/SUNWrasag/lib/URI/data.pm /opt/SUNWrasag/lib/URI/file.pm /opt/SUNWrasag/lib/URI/file/Base.pm /opt/SUNWrasag/lib/URI/file/FAT.pm /opt/SUNWrasag/lib/URI/file/Mac.pm /opt/SUNWrasag/lib/URI/file/OS2.pm /opt/SUNWrasag/lib/URI/file/Unix.pm /opt/SUNWrasag/lib/URI/file/Win32.pm /opt/SUNWrasag/lib/URI/ftp.pm /opt/SUNWrasag/lib/URI/gopher.pm /opt/SUNWrasag/lib/URI/http.pm /opt/SUNWrasag/lib/URI/https.pm /opt/SUNWrasag/lib/URI/ldap.
CODE EXAMPLE D-1 /opt/SUNWrasag/lib/auto/Filter/Util/Exec/Exec.so /opt/SUNWrasag/lib/auto/Filter/decrypt/decrypt.bs /opt/SUNWrasag/lib/auto/Filter/decrypt/decrypt.so /opt/SUNWrasag/lib/auto/Filter/tee/tee.bs /opt/SUNWrasag/lib/auto/Filter/tee/tee.so /opt/SUNWrasag/lib/auto/GDBM_File/.packlist /opt/SUNWrasag/lib/auto/GDBM_File/GDBM_File.bs /opt/SUNWrasag/lib/auto/GDBM_File/GDBM_File.so /opt/SUNWrasag/lib/auto/GDBM_File/autosplit.ix /opt/SUNWrasag/lib/auto/IO/IO.bs /opt/SUNWrasag/lib/auto/IO/IO.
CODE EXAMPLE D-1 /opt/SUNWrasag/lib/date.sh /opt/SUNWrasag/lib/myMenu.js /opt/SUNWrasag/lib/newhtml.pl /opt/SUNWrasag/lib/ras_telnet.pl /opt/SUNWrasag/lib/read_config.pl /opt/SUNWrasag/lib/sdt.pl /opt/SUNWrasag/lib/string.pl /opt/SUNWrasag/lib/subroutines.pm /opt/SUNWrasag/lib/template.pod /opt/SUNWrasag/lib/template_pod.pl /opt/SUNWrasag/lib/test_events.pl /opt/SUNWrasag/man/man1m/checkcron.1m /opt/SUNWrasag/man/man1m/clearcache.1m /opt/SUNWrasag/man/man1m/disk_inquiry.
CODE EXAMPLE D-1 /opt/SUNWrasag/snmp/mibs/v2_2FA.mib /opt/SUNWrasag/snmp/mibs/v2_2FE.mib /opt/SUNWrasag/snmp/mibs/v2_2SW.txt /opt/SUNWrasag/tmp/Catalog.pm /opt/SUNWrasag/tmp/ConfigFile.pm /opt/SUNWrasag/tmp/Graph.pm /opt/SUNWrasag/tmp/T3Agent.pm /opt/SUNWrasag/tmp/TO.pm /opt/SUNWrasag/tmp/TOPOAgent.pm /opt/SUNWrasag/tmp/WWNINFO [ verifying class ] ## Executing postinstall script. libsnmp-0.4.2.0.2.so Using ‘/usr/bin/perl’ version 5.
CODE EXAMPLE D-1 permission during the process of installing this package. Do you want to continue with the installation of [y,n,?] y Installing SANsurfer, QLogic Fibre Channel Administration as ## Installing part 1 of 1. /usr/opt/SUNWsmgr/app.dat /usr/opt/SUNWsmgr/bin/Sun.jar /usr/opt/SUNWsmgr/bin/esm_smgr /usr/opt/SUNWsmgr/default.fab /usr/opt/SUNWsmgr/flash/m08030462.fls /usr/opt/SUNWsmgr/flash/m16030462.fls /usr/opt/SUNWsmgr/jre/COPYRIGHT /usr/opt/SUNWsmgr/jre/ControlPanel.
CODE EXAMPLE D-1 /usr/opt/SUNWsmgr/jre/lib/font.properties /usr/opt/SUNWsmgr/jre/lib/font.properties.5.5.1 /usr/opt/SUNWsmgr/jre/lib/font.properties.ISO8859_13 /usr/opt/SUNWsmgr/jre/lib/font.properties.ISO8859_13.5.7 /usr/opt/SUNWsmgr/jre/lib/font.properties.ISO8859_15_FDIS /usr/opt/SUNWsmgr/jre/lib/font.properties.ISO8859_2 /usr/opt/SUNWsmgr/jre/lib/font.properties.ISO8859_4 /usr/opt/SUNWsmgr/jre/lib/font.properties.ISO8859_5 /usr/opt/SUNWsmgr/jre/lib/font.properties.
CODE EXAMPLE D-1 /usr/opt/SUNWsmgr/jre/lib/fonts/LucidaSansOblique.ttf /usr/opt/SUNWsmgr/jre/lib/fonts/LucidaSansRegular.ttf /usr/opt/SUNWsmgr/jre/lib/fonts/LucidaTypewriterBold.ttf /usr/opt/SUNWsmgr/jre/lib/fonts/LucidaTypewriterBoldOblique.ttf /usr/opt/SUNWsmgr/jre/lib/fonts/LucidaTypewriterOblique.ttf /usr/opt/SUNWsmgr/jre/lib/fonts/LucidaTypewriterRegular.ttf /usr/opt/SUNWsmgr/jre/lib/fonts/fonts.dir /usr/opt/SUNWsmgr/jre/lib/i18n.jar /usr/opt/SUNWsmgr/jre/lib/images/cursors/cursors.
CODE EXAMPLE D-1 /usr/opt/SUNWsmgr/jre/lib/sparc/libjdgaSUNWafb.so /usr/opt/SUNWsmgr/jre/lib/sparc/libjdgaSUNWcg6.so /usr/opt/SUNWsmgr/jre/lib/sparc/libjdgaSUNWffb.so /usr/opt/SUNWsmgr/jre/lib/sparc/libjdgaSUNWm64.so /usr/opt/SUNWsmgr/jre/lib/sparc/libjpeg.so /usr/opt/SUNWsmgr/jre/lib/sparc/libjsound.so /usr/opt/SUNWsmgr/jre/lib/sparc/libjvm.so /usr/opt/SUNWsmgr/jre/lib/sparc/libmlib_image.so /usr/opt/SUNWsmgr/jre/lib/sparc/libmlib_image_v.so /usr/opt/SUNWsmgr/jre/lib/sparc/libmon_Axil-210.
CODE EXAMPLE D-1 /usr/opt/SUNWsmgr/jre/lib/sparc/libmon_SUNW,SPARCserver-2000.so /usr/opt/SUNWsmgr/jre/lib/sparc/libmon_SUNW,SPARCstation10,SX.so /usr/opt/SUNWsmgr/jre/lib/sparc/libmon_SUNW,SPARCstation-10.so /usr/opt/SUNWsmgr/jre/lib/sparc/libmon_SUNW,SPARCstation-20.so /usr/opt/SUNWsmgr/jre/lib/sparc/libmon_SUNW,SPARCstation-4.so /usr/opt/SUNWsmgr/jre/lib/sparc/libmon_SUNW,SPARCstation-5.
CODE EXAMPLE D-1 /usr/opt/SUNWsmgr/jre/lib/sparc/libmon_Tadpole_S3000XT.so /usr/opt/SUNWsmgr/jre/lib/sparc/libmon_Tadpole_S3GS.so /usr/opt/SUNWsmgr/jre/lib/sparc/libmon_Tadpole_S3GX.so /usr/opt/SUNWsmgr/jre/lib/sparc/libmon_Tadpole_S3LC.so /usr/opt/SUNWsmgr/jre/lib/sparc/libmon_Tadpole_S3TS.so /usr/opt/SUNWsmgr/jre/lib/sparc/libmon_Tadpole_S3TX.so /usr/opt/SUNWsmgr/jre/lib/sparc/libmon_Tadpole_S3XP.
CODE EXAMPLE D-1 /usr/opt/SUNWsmgr/bin/esm_smgr Installation of was successful. # patchadd /download/110696-03 Checking installed patches... Verifying sufficient filesystem capacity (dry run method)... Installing patch packages... Patch number 110696-03 has been successfully installed.
204 Sun StorEdge Network FC Switch-8 and Switch-16 Installation and Configuration Guide • October 2001
Glossary This glossary contains a definitions for terms used in this guide. Terms AL_PA FL_Port F_Port Arbitrated Loop Physical Address; 8-bit value used to identify a device. On a Fibre Channel switch, a port that supports Arbitrated Loop devices. On a Fibre Channel switch, a port that supports an N_Port. A Fibre Channel port in a point-to-point or Fabric connection. N_Port NL_Port G_Port SL_Port T_Port TL_Port A Fibre Channel port in a point-to-point or Fabric connection.
Zoning Zoning allows the user to divide the Fabric ports into zones for more efficient and secure communication among functionally grouped nodes. There are several types of zones and a port may be defined in any. No port can be in all zone types simultaneously. Hard Zones Hard Zones allow the division of the Fabric (one or more Switch chassis) into as many as 16 Fabric-wide zones that define the ports that can communicate with each other.
