Installation Guide

ManualsBrandsSun-Mar ManualsBathMobile Electric Waterless Self Contained Composting Toilet for Mobile Applications in Bone

MOBILE Toilet Installation

- 6 –

Anchoring the

Mobile

“S” Shaped

Bracket

‘L’ Shaped

Brackets

The mobile should be anchored if the unit will be installed in a vehicle that will move. There

are three anchoring brackets supplied with the unit which should be used to securely

anchor the toilet.

The ‘S’ shaped mounting bracket -

The ‘S’ shaped mounting bracket, (pictured below) is for attaching the top of the toilet to

the wall. (see diagram below)

1. Locate the ‘S’ Bracket (shown above), 2 nuts, 2 washers and

2 bolts.

2. Locate the two dimples (guides where to drill holes) that are just

left of centre, near the top of the unit.

3. Place the ‘S’ Bracket over the dimples to make sure the holes line

up. Using an electric drill with the drill bit(provided), drill a hole

through each of the 2 dimples on the top of the unit.

4. Place the ‘S’ bracket over the holes so that the top end of the

bracket is above the top of the unit (as shown in diagram left).

Once the bracket is in place, insert a bolt through each hole so that it is visible through the

vent hole in the top of the unit (see diagram below). Run a thin bead of silicone around the

stainless steel washer (provided) and place over the protruding bolt, on the inside of the

unit. Place a stainless steel nut over each protruding bolt and tighten.

Fastening the bracket to the wall:

1. Place the MOBILE against the wall where it will be mounted.

2. With a pencil, mark the location of the holes in the mounting

bracket.

3. Drill a small hole in each of the pencil markings to accept

anchoring screws. Use a #8 x 1” screw to anchor the

unit to the wall. Once installed, the vent pipe will hide the

bracket.

The ‘L’ bracket, (pictured left) is for attaching the toilet to the floor. (see diagram below)

1. Locate the ‘L’ Bracket in the desired location.

2. Remove the finishing drawer. Using the holes in the ‘L’ bracket as a guide, mark the

location of the two holes with a pencil. Use a drill with the drill bit (provided) to create

small holes in the side of the MOBILE tank being careful not to drill downward toward

the heating element.

3. Make sure the drilled holes line up with the holes in the

‘L’ bracket..

4. Place a small bead of silicone over the hole between

the ‘L’ bracket and the Mobile tank. Dip the bolt into

silicone and insert the bolt into the hole in the bracket

and through the corresponding hole in the Mobile tank.

5. Place a small amount of silicone into the centre of the

nut and fasten over the bolt to fasten the bracket.

Important: Ensure all bolts used for brackets are

sealed with silicone to prevent leakage.

Summary of content (2 pages)

PAGE 1
MOBILE Toilet Installation Anchoring the Mobile “S” Shaped Bracket The mobile should be anchored if the unit will be installed in a vehicle that will move. There are three anchoring brackets supplied with the unit which should be used to securely anchor the toilet. The ‘S’ shaped mounting bracket The ‘S’ shaped mounting bracket, (pictured below) is for attaching the top of the toilet to the wall. (see diagram below) 1. Locate the ‘S’ Bracket (shown above), 2 nuts, 2 washers and 2 bolts. 2.
PAGE 2
Space Required and other Installation Considerations 1. Compost is removed from the finishing drawer. Ensure that there is at least 15” in front of the MOBILE Toilet so that the drawer may be removed from the unit. 2. Install the unit in a location where the safety drain can be connected. This drain exits from the back of the unit and must slope downward at all points. 3. Install in a location where the vent pipe can be attached as per the instructions listed on page #9. 4.