“Bright As Day!”® Power-Port Desk Lamp SI561 Instructions Read and save these instructions. SI561 IM_v2 1106.
Dear Sharper Image Customer, Thank you for your purchase of a Sharper Image product. We appreciate your business very much. Our goal is that you will be completely satisfied with this product’s quality and performance. We offer generous return privileges and excellent warranties on all our products. Since 1977, The Sharper Image has shared the fun of discovering innovative products that make life better and more enjoyable.
IMPORTANT SAFETY INSTRUCTIONS When using electrical appliances, basic safety precautions should always be followed. Read all Instructions Before Using. Lighted lamp is HOT. WARNING - TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, EXPOSURE TO EXCESSIVE UV, RADIATION OR INJURY TO PERSONS: 1. Before replacing the bulb, turn off/unplug and allow the lamp to cool. 2. Lamp becomes HOT quickly! Only touch the switch/plug when turning on the lamp. 3. Do not touch hot lamp-containment barrier. 4.
IMPORTANT SAFETY INSTRUCTIONS 8. Do not operate the lamp with a missing or damaged guard or lamp-containment barrier. 9. When connecting an AC appliance to the built-in AC outlets on the base, refer to the power rating of the connected appliance and do not exceed 5A total power load on one or both outlets combined. 10. Warning: To maintain a good balance and to prevent the lamp from tipping over, keep the lowest section of the adjustable arms at or above a 72-degree angle from horizontal.
Precautions RISK OF FIRE: Failure to read and follow these precautions could result in risk of fire. 1. Do not use with power supply voltage other than 120V AC. 2. Do not use outdoors or in locations with high humidity, such as bathrooms. 3. Do not install above sources of high heat, such as a stove or heater. 4. Do not touch the lamp while it is lit or immediately after turning off the lamp. Maintenance Caution: If any malfunction occurs, do not try to repair the unit yourself.
General Instructions Parts Diagram Adjustment Knobs Lamp Cover Arms Lamp/Bulb (FML27) Base Grounded Power Outlets SI561 IM_v2 1106.
Assembly 1. Remove the plastic packing materials from the light fixture. 2. Remove the foam shipping guard from behind the preinstalled lamp. Note: The lamp socket (containment barrier) pivots out. Be certain to push the lamp and socket back into the fixture. (See Figure A below.) Figure A 3. To adjust the lamp height and angle, loosen the knobs on the fixture arms and move the arms to the desired height and angle, then tighten the knobs to secure the new positions. SI561 IM_v2 1106.
Operation 1. Plug the lamp into a 110-120V three-prong power outlet. 2. Turn the POWER CONTROL KNOB to turn the light on or off. Power Control Knob Grounded Power Outlets USB Port The built-in AC power outlets can be used to connect up to two separate chargers or other AC appliances. Do not exceed 5A total power load on one or both outlets combined. The built-in USB power port can be used to connect, power and charge compatible USB products.
Lamp Replacement 1. The lamp and socket pivot out for easy replacement. Gently pull the lamp out and slide the lamp out of the fixture socket. (See Figure B below.) Figure B 2. Replace with a new lamp. Replacement lamps are available from The Sharper Image (Item No. SI928). Do not use any other lamp with this product. 3. Gently push the lamp and socket back into place. (See Figure C below.) Figure C SI561 IM_v2 1106.
Statement of FCC Compliance — Model SI561 WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Statement of FCC Compliance — Model SI561 • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for assistance.
One-Year Warranty What Is Covered This warranty covers any defects in materials or workmanship, with the exceptions stated below. How Long Coverage Lasts This warranty runs for one year from the date of original purchase. What Is Not Covered This warranty does not cover damage caused by misuse or use other than as intended and described in the product instruction manual, or loss or damage to batteries or removable parts.
