R 13A ELECTRIC PRESSURE WASHER 2100 PSI MAX PRESSURE AT INITIAL DISCHARGE PER CSA INTERNAL PRESSURE TESTING OPERATOR’S MANUAL A Division of Snow Joe®, LLC © 2022 by Snow Joe®, LLC All rights reserved. Original instructions. 1.8 GPM MAX FLOW WITH NOZZLE OPEN AT MINIMUM PRESSURE Model SPX2005P-RM Form No.
R 13A ELECTRIC PRESSURE WASHER 2100 PSI MAX PRESSURE AT INITIAL DISCHARGE PER CSA INTERNAL PRESSURE TESTING OPERATOR’S MANUAL A Division of Snow Joe®, LLC 1.8 GPM MAX FLOW WITH NOZZLE OPEN AT MINIMUM PRESSURE Model SPX2005P-RM Form No. SJ-SPX2005P-RM-880E-M-V1 • mCAUTION! – Exercise caution to avoid slipping or falling. Wear protective footwear that will protect your feet and improve your footing on slippery surfaces. IMPORTANT! Safety Instructions • Stay alert – Watch what you are doing.
mWARNING! Risk of injection or injury – Do not direct • In the event of an accident or breakdown, switch off the machine immediately (If contact with detergent occurs, rinse with an abundance of clean water.) discharge stream at persons. mWARNING! High-pressure jets can be dangerous if Electrical Safety subject to misuse. The jet must not be directed at persons, pets, live electrical equipment, or the appliance itself.
mWARNING! To reduce the risk of electrocution, keep 3. Ground fault circuit interrupter (GFCI) protection – This pressure washer is provided with a ground-fault circuit-interrupter (GFCI) built into the plug of the powersupply cord. This device provides additional protection from the risk of electric shock. Should replacement of the plug or cord become necessary, use only identical replacement parts that include GFCI protection. all connections dry and off the ground. Do not touch plug with wet hand. 6.
Product Description Purpose • This high-pressure electric power washer is intended for residential use only. It is designed for light-to-medium duty cleaning jobs on boats, motorcycles, RVs, ATVs, trailers, decks, barbecues, siding, patio furniture, and more. Areas of application • Never use the machine in potentially explosive areas under any circumstances! • The operating temperature must be between 32ºF (0ºC) and 104ºF (40ºC).
Safety Symbols The following table depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the machine before attempting to assemble and operate. Symbols Descriptions Symbols Descriptions READ THE OPERATOR'S MANUAL(S) – Read, understand, and follow all instructions in the user manual(s) before attempting to assemble and operate. WARNING! Electrical shock hazard. SAFETY ALERT – Indicates a precaution, a warning, or a danger.
Know Your Electric Pressure Washer Read the owner’s manual and safety rules carefully before operating the pressure washer. Compare the illustration below to the pressure washer in order to familiarize yourself with the location of the various controls and adjustments. Save this manual for future reference. 1. Trigger gun holder 9. Foam cannon (SPX-FC26) 16. Rear compartment 2. ON/OFF switch 10. Wheels (2) 17. 15º Quick-Connect nozzle (yellow) 3. Water inlet (garden hose connection) 11.
Unpacking Assembly Carton Contents Tools required: Phillips head screwdriver 1. Lay unit on its side. Firmly press the wheel onto the unit body until it locks into place. Repeat on the opposite side (Fig. 1). • Electric pressure washer • Transport handle • Trigger gun • Quick-Connect spray wand Fig.
3. Slide the trigger gun holder into position (Fig. 3). Fig. 5 Fig. 3 Insert the tab into the hole Trigger gun holder Rear compartment Fig. 6 4. Slide the hose/cord holder into position (Fig. 4). Fig. 4 Rear compartment Hose/ cord holder Small Phillips head screws 6. Fit the spray wand into the gun and turn the rotatable end-piece of the wand until the two parts are completely locked (Fig. 7). 5. Fit the 4 small tabs on the rear compartment into the holes in the back of the machine.
Fig. 8 (FRONT) Fig. 10 Trigger gun Garden hose (male end) This end to water inlet Water inlet (female coupler) High-pressure hose Garden hose 10. Attach garden hose to water supply (Fig. 11). 8. Connect the other end of the high-pressure hose to the water outlet on the pressure washer (Fig. 9). First, push the high-pressure hose end completely onto the high-pressure water outlet, then screw it on clockwise. Tighten securely. Fig. 9 Fig.
. Make sure the motor switch is pushed to the OFF (0) position before plugging the unit into the power outlet (Fig. 12). Fig. 12 OFF/0 ON/l Operation mIMPORTANT! This pressure washer is equipped with a micro-switch sensitive to water flow. This Total Stop System (TSS) senses water flow in the pump. When the trigger is released, water stops flowing through the pump. The TSS then automatically turns the motor off to protect the pump from overheating, thus saving energy and prolonging pump life. 1.
3. Remove the nozzle by disconnecting it while pulling back the brass Quick-Connect collar. Using Nozzles Before beginning any cleaning task, determine the best nozzle for the job. Each of the nozzles has a different spray pattern. The nozzle patterns are 40˚ (for all-purpose cleaning), 15˚ (for tough jobs), and 0˚ (for spot cleaning or hard-to-reach areas).
3. Disconnect the Quick-Connect spray wand from the trigger gun by twisting counter-clockwise until the 2 locking tabs of the spray wand can be removed from the slot (Fig. 20). 6. Apply detergent from the bottom to the top of the dry surface to be cleaned. NOTE: Wetting the surface first is not recommended as it dilutes the detergent and reduces its cleaning ability. 7. Allow the detergent to remain on the surface for a short time before rinsing. Do not allow the detergent to dry on the surface.
6. To connect the surface cleaner assembly with the trigger gun, firmly push the locking tabs of the surface cleaner extension wand into the slot of the trigger gun and turn the rotatable end-piece of the wand until the two parts are completely locked together (Fig. 27). 2. Flip the surface cleaner over and align the dual-nozzle rotating sprayer with the attachment of the surface cleaner (Fig. 24). Fig. 24 Surface cleaner Fig.
mCAUTION! The use of a pump protector is Fig. 29 recommended to prevent cold weather damage during storage over the winter months. Winterizing + long-term storage Inlet filter If you must store your pressure washer in a location where the temperature falls below 32ºF (0ºC), you can minimize the chance of damage to your machine by utilizing the following procedure: • Disconnect all water connections. • Turn on the machine for a few seconds until the remaining water in the pump exits.
Disposal Recycling the washer • Do not dispose of electrical appliances as unsorted municipal waste. Use separate collection facilities. • Contact your local government agency for information regarding the collection systems available. • If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the groundwater and get into the food chain, damaging your health and well-being.
Troubleshooting • Disconnect the unit from the electrical power supply before carrying out maintenance on the machine or when checking that its parts are in proper working order. • To avoid unnecessary hassles, consult the following table before contacting customer service with any mechanical issues. Problems Machine refuses to start Possible Cause Possible Solution • Power failure/machine not plugged into a working receptacle. • Check to make sure machine is plugged into a working outlet.
Optional Accessories mWARNING! ALWAYS use only authorized Snow Joe ® + Sun Joe® replacement parts and accessories. NEVER use replacement parts or accessories that are not intended for use with this electric pressure washer. Contact Snow Joe® + Sun Joe® if you are unsure whether it is safe to use a particular replacement part or accessory with your pressure washer. The use of any other attachment or accessory can be dangerous and could cause injury or mechanical damage.
Accessories Item Model 5 Dual-Nozzle Rotating Surface Cleaner SPX-PCA10 Sun Joe’s complete line of premium pressure washer accessories and attachments make it easy to get your dirty work done, and also help you get the most out of your model! SHOP ONLINE now at sunjoe.com NOTE: Accessories are subject to change without any obligation on the part of Snow Joe® + Sun Joe® to provide notice of such changes. Accessories can be ordered online at sunjoe.
SNOW JOE® + SUN JOE® REFURBISHED GOODS WARRANTY GENERAL CONDITIONS: Snow Joe® + Sun Joe® may from time to time change the design of its products. Nothing contained in this warranty shall be construed as obligating Snow Joe® + Sun Joe® to incorporate such design changes into previously manufactured products, nor shall such changes be construed as an admission that previous designs were defective.
20
21
22
sunjoe.
