R 13A ELECTRIC PRESSURE WASHER 2100 PSI MAX PRESSURE AT INITIAL DISCHARGE PER CSA INTERNAL PRESSURE TESTING 1.8 GPM MAX FLOW WITH NOZZLE OPEN AT MINIMUM PRESSURE OPERATOR’S MANUAL A Division of Snow Joe®, LLC © 2021 by Snow Joe®, LLC All rights reserved. Original instructions. Model SPX2004-RM Form No.
R 13A ELECTRIC PRESSURE WASHER 2100 PSI MAX PRESSURE AT INITIAL DISCHARGE PER CSA INTERNAL PRESSURE TESTING 1.8 GPM MAX FLOW WITH NOZZLE OPEN AT MINIMUM PRESSURE OPERATOR’S MANUAL A Division of Snow Joe®, LLC Model SPX2004-RM Form No. SJ-SPX2004-RM-880E-M-V1 • mCAUTION! – Exercise caution to avoid slipping or falling. Wear protective footwear that will protect your feet and improve your footing on slippery surfaces. IMPORTANT! Safety Instructions • Stay alert – Watch what you are doing.
mWARNING! Risk of injection or injury – Do not direct • In the event of an accident or breakdown, switch off the machine immediately (If contact with detergent occurs, rinse with an abundance of clean water.) discharge stream at persons. mWARNING! High-pressure jets can be dangerous if Electrical Safety subject to misuse. The jet must not be directed at persons, pets, live electrical equipment, or the appliance itself.
mWARNING! To reduce the risk of electrocution, keep 3. Ground fault circuit interrupter (GFCI) protection – This pressure washer is provided with a ground-fault circuit-interrupter (GFCI) built into the plug of the powersupply cord. This device provides additional protection from the risk of electric shock. Should replacement of the plug or cord become necessary, use only identical replacement parts that include GFCI protection. all connections dry and off the ground. Do not touch plug with wet hand. 6.
Product Description Purpose • This high-pressure electric power washer is intended for residential use only. It is designed for light-to-medium duty cleaning jobs on boats, motorcycles, RVs, ATVs, trailers, decks, barbecues, siding, patio furniture, and more. Areas of application • Never use the machine in potentially explosive areas under any circumstances! • The operating temperature must be between 32ºF (0ºC) and 104ºF (40ºC).
Safety Symbols The following table depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the machine before attempting to assemble and operate. Symbols Descriptions Symbols Descriptions READ THE OPERATOR'S MANUAL(S) – Read, understand, and follow all instructions in the user manual(s) before attempting to assemble and operate. WARNING! Electrical shock hazard. SAFETY ALERT – Indicates a precaution, a warning, or a danger.
Know Your Electric Pressure Washer Read the owner’s manual and safety rules carefully before operating the pressure washer. Compare the illustration below to the pressure washer in order to familiarize yourself with the location of the various controls and adjustments. Save this manual for future reference. 1. ON/OFF switch 9. High-pressure hose 16. Trigger gun holder 2. Water inlet (garden hose connection) 10. Rear compartment 17. Quick-Connect spray wand 3. Transport handle 11.
Unpacking Assembly Carton Contents Tools required: Phillips head screwdriver 1. Lay unit on its side. Firmly press the wheel onto the unit body until it locks into place. Repeat on the opposite side (Fig. 1). • Electric pressure washer • Transport handle • Trigger gun • Quick-Connect spray wand Fig.
3. Slide the hose/cord holder into position (Fig. 3). Fig. 6 Fig. 3 Rear compartment Hose/ cord holder Small Phillips head screws 6. Fit the Quick-Connect spray wand into the trigger gun and twist the rotatable end-piece of the wand until the two parts are completely locked (Fig. 7). 4. Slide the trigger gun holder into position (Fig. 4). Fig. 4 Trigger gun Fig. 7 Trigger gun holder Quick-Connect spray wand 7.
8. Connect the other end of the high-pressure hose to the water outlet on the pressure washer (Fig. 9). First, push the high-pressure hose end completely onto the high-pressure water outlet, then screw it on clockwise. Tighten securely. Fig. 9 10. Attach garden hose to water supply (Fig. 11). Fig. 11 (BACK) Connect to water supply High-pressure hose Garden hose mWARNING! The intake water temperature must High-pressure water outlet not exceed 104ºF/40ºC. The water supply must not exceed 0.7 MPa.
12. Check that the electrical supply voltage and frequency (Volt/Hz) correspond to those specified on the pressure washer rating plate. If the power supply is correct, you may now plug the pressure washer into the power outlet (Fig. 13). 3. Turn the water supply tap on completely. 4. Unlock the safety lock, then press the trigger for a few seconds until the water flow is steady. Operating the pressure washer in this manner will allow air to escape and discharge residual pressure in the hose (Fig. 15).
m CAUTION! NEVER change nozzles without locking the safety lock on the trigger handle. mWARNING! High-pressure jets can be dangerous if subject to misuse. The jet must not be directed at persons, pets, live electrical equipment, or the appliance itself. This electric pressure washer is equipped with three (3) Quick-Connect nozzles that easily snap onto the Quick-Connect collar of the spray wand. Using the Adjustable Jet Nozzle mWARNING! High-pressure jets can be dangerous if subject to misuse.
2. Remove the cap. Fill the bottle or mix as recommended by detergent instructions (Fig. 22), and secure the cap back into place. Replace it back on the unit. Using the 90º Angled Nozzle 90 degree angled nozzle directs the water into hard to reach areas (Fig. 20). This nozzle is the ideal for removing dirt from car wheel wells and cleaning and clearing blocked gutters. Fig. 22 Fig. 20 90º nozzle tip Detergent for pressure washer Foam cannon bottle 3.
2. Turn off the water source. Fig. 25 Decrease soap volume 3. Hold the trigger to release water pressure. 4. Disconnect the garden hose from the water inlet on the unit. Increase soap volume 5. Disconnect the high-pressure hose connection on the trigger gun handle. Adjustable cap Rotate spray angle 360º 6. Release the trigger and engage the gun safety lock. mWARNING! Turn off the water supply and squeeze the trigger to depressurize the unit.
mWARNING! Before reusing, completely flush the unit 2. Clean the nozzle with the needle clean-out tool provided (Fig. 29). Remove the spray wand from the gun; remove any dirt from the nozzle hole and rinse. out with clear water. Anti-freeze products can damage paintwork, so you must ensure there is no anti-freeze left in the system before using it again. Fig. 29 Maintenance mCAUTION! Before working on the pressure washer, disconnect the plug from the power supply socket. 1.
Troubleshooting • Disconnect the unit from the electrical power supply before carrying out maintenance on the machine or when checking that its parts are in proper working order. • To avoid unnecessary hassles, consult the following table before contacting customer service with any mechanical issues. Problems Machine refuses to start Possible Cause Possible Solution • Power failure/machine not plugged into a working receptacle. • Check to make sure machine is plugged into a working outlet.
Optional Accessories mWARNING! ALWAYS use only authorized Snow Joe ® + Sun Joe® replacement parts and accessories. NEVER use replacement parts or accessories that are not intended for use with this electric pressure washer. Contact Snow Joe® + Sun Joe® if you are unsure whether it is safe to use a particular replacement part or accessory with your pressure washer. The use of any other attachment or accessory can be dangerous and could cause injury or mechanical damage.
Accessories Item Model 5 Quick-Connect Turbo Nozzle Tip SPX-QCTB4 Quick-Connect 90 Degree Angled Nozzle Tip SPX-QC904 Quick-Connect Jet Nozzle Tip SPX-QCJT4 25.4 fl oz Adjustable Foam Cannon SPX-FC26 6 7 8 Sun Joe’s complete line of premium pressure washer accessories and attachments make it easy to get your dirty work done, and also help you get the most out of your model! SHOP ONLINE now at sunjoe.
SNOW JOE® + SUN JOE® REFURBISHED GOODS WARRANTY GENERAL CONDITIONS: Snow Joe® + Sun Joe® may from time to time change the design of its products. Nothing contained in this warranty shall be construed as obligating Snow Joe® + Sun Joe® to incorporate such design changes into previously manufactured products, nor shall such changes be construed as an admission that previous designs were defective.
sunjoe.
