Replacement Part List

11
5. Move all four wheels to the desired cutting height by
pulling back on the rod axle and setting it to the correct
position. Make sure all four wheels are at the same cutting
height position.
NOTE: Set the mower to the highest cutting height when
mowing on uneven ground or in tall weeds.
6. Place the lawn mower back on to its wheels and reattach
the grass bag.
7. Reconnect the power supply to the mower and resume
normal use.
Maintenance + Care
mWARNING! Before cleaning, repairing or inspecting the
mower, disconnect the power supply to the unit and verify that
all moving parts have come to a complete stop.
General
• Always keep the mower clean and free of grass, dirt or
other debris.
• Keep the handles dry, clean and free of oil and grease.
• After each cutting session, remove acccumulated grass
clippings and debris using either a dry cloth or handbrush.
You may also clean the equipment with a damp cloth and
some soft, non-abrasive soap. Do not use cleaning agents
or harsh solvents as they may damage the equipment's
plastic components. Make sure that no water penetrates
the equipment's interior as intake of water can destroy the
switch/plug mechanism and the electric motor.
• Do not clean the lawn mower with running water,
particularly with high-pressure water.
• Check all nuts, bolts and screws for proper tightness
before each use.
• Frequently inspect the grass bag assembly for signs of
wear and replace immediately with a genuine Snow Joe
®
+ Sun Joe
®
part if damage is found.
• Replace excessively worn or damaged parts immediately.
• To maximize your mower's longevity, all screwed parts,
including the wheels and axles, should be cleaned and
lubricated. There are no parts inside the equipment which
require additional maintenance or lubrication.
Blade Maintenance
IMPORTANT: The mower blade is sharp and can cause severe
personal injury if handled incorrectly. Wrap the blade or wear
protective gloves, and use extra caution when handling.
The steel blade is designed to provide a ne cut in long or
tough grass. Deterioration in the quality of cut indicates blade
wear or damage. Follow these steps to determine if the blade
needs to be resharpened or replaced:
1. Disconnect the electrical supply to the mower.
2. Turn the mower on its side to expose the underside of the
blade housing.
3. Check the blade.
a. If the blade is blunt or has minor wear, then resharpen.
Contact an authorized Snow Joe
®
+ Sun Joe
®
service
center.
b. If the blade shows signs of major wear or damage (i.e.:
gouged, bent), replace. Please call Snow Joe
®
+
Sun Joe
®
customer service for assistance at
1-866-SNOWJOE (1-866-766-9563).
mWARNING! An excessively vibrating mower indicates
that the blade is not properly balanced or has become
deformed from striking an object. In this case, the blade must
be repaired or replaced. Please follow the proper maintenance
procedures for blade care or call the Snow Joe
®
+ Sun Joe
®
customer service center for assistance at 1-866-SNOWJOE
(1-866-766-9563).
Blade Replacement
IMPORTANT: Only use original replacement parts specied for
this mower.
You can purchase a replacement blade (Model MJ401E-11)
and other genuine replacement parts by visiting us online at
snowjoe.com or calling our toll-free customer service helpline
at 1-866-SNOWJOE (1-866-766-9563). The use of parts that
do not meet the original equipment specications may lead to
improper performance of the lawn mower, may compromise
operator safety and will void the manufacturer's warranty.
1. Disconnect the electrical supply to the mower.
2. Turn the mower on its side to expose the underside of the
blade housing.
3. Use a cloth to grip the blade or wear heavy-duty gloves.
4. Using the spanner provided, remove the bolt and
the washer securing the blade by turning the bolt
counterclockwise, then carefully remove the blade
(Fig. 14).
Fig. 14
Blade
Spanner